If the PX4FMUv2 board does not have the v5 uploader, it's not possible
to check the silicon revision to make sure it's safe to upload the
firmware which is more than 1 MB. However, if the user is sure the
silicon revision is not affected by this errata, he can upload the
firmware using px4_uploader.py with --force argument. This commit adds
`force-upload` make target to do it more convenient way.
Signed-off-by: Andrei Korigodski <akorigod@gmail.com>
to disable automatic evaluation of /dev/ttyS* expression in cygwin.
On linux verbatim seems to be default anyways. At least it doesn't get
evaluated on linux.
These hard coded paths assume all Nuttx targets are ARMv7-M targets. Updating them to use ${CONFIG_ARCH} and ${CONFIG_ARCH_FAMILY} instead allows for the architecture defined by the incoming Nuttx defconfig to be correctly targeted.
Flight tested: ekf2 w/ mag and compass by @nathantsoi: https://logs.px4.io/plot_app?log=79b81031-cf1e-41f0-890b-d6cd7d559766
NOTE: external I2C devices need a pullup. I have tested with a 3.3v 2.2k pullup.
Working:
- mpu6000, bench tested and verified via nsh
- fmu
- all 6 ch output bench tested w/ pwm and oneshot via nsh
- ppm input bench tested
- dsm input bench tested
- bmp280, bench tested and verified via nsh
- hmc5883, bench tested and verified via nsh, but requires an external i2c pullup
- gps on uart6
- startuplog, nsh, mavlink on uart4, but params are not sent for some reason. RSSI pin is TX, MOTOR 5 is RX (normal mode, 57600 baud)
- rgbled over i2c, bench tested and workingp
- sbus via the shared sbus/ppm pin (which includes an inverter to the mcu SBUS in pin), remove the solder bridge or jumper to the ppm pin before use
Not yet implemented:
- ADC
- OSD: passthrough video is untested, use at your own risk until a basic driver is implemented.
In the Cygwin environment the native Windows serial COM# ports get mapped
to /dev/ttyS# for POSIX compatibility. While # is one number lower inside
the environment than the COM port number because it's 0 indexed instead
of 1.
I added the necessary handling to all the dependent parts I found which
allows uploading to /dev/ttyS# when the cygwin platform is detected.
Now the usual "make px4fmu-v4 upload" and
"./Tools/upload.sh build/px4fmu-v4_default/px4fmu-v4_default.px4" work.
This change fragments MAVLink packets more efficiently and therefore increases the net throughput. This in turn makes the connection significantly more stable and the Crazyflie experience overall more usable.
In the stm32f7 the configuration variable for SD card with DMA changed from CONFIG_STM32_SDIO_DMA to CONFIG_STM32F7_SDMMC_DMA
the maximum clock speed of 16MHz can now be achieved.
* Cygwin: repaired NuttX build after 1f63d85869
all the NuttX specific WINTOOL define handling was skiped in cmake Make.defs generation
The Nuttx build is makfile based and needs its cygwin treatment
Additionally the ${PX4_SOURCE_DIR}/src/include which was added through cmake needs path conversion
The two root causes for the special handling are:
- ARM GCC for Windows doesn't support cygwin paths passed as an argument
so they need to be either relative or converted via cypath tool
- Symbolic links are totally different under Windows and because NuttX uses them extensively
it has special handling scripts that need to be fed with the correct defines
* Cygwin: NuttX include paths all converted in Make.defs.in
differentiate between WINTOOL define (MSYS & cygwin) and cygwin using uname command:
- MSYS needs symbolic link handling for ARM GCC but no path conversion
- Cygwin needs both
This is a temporary workaround for equal expressions in chip/sam_xdmac.c
and can be reverted once fixed properly in NuttX. Needed for the GCC 7
upgrade in #8551.
Daniel Agar
PX4 Jenkins
korigod
David Sidrane
MaEtUgR
Beat Küng
Joshua Whitehead
DanielePettenuzzo
nathan
barzanisar
Lorenz Meier
Jan Okle
Simone Guscetti