* Creating a base for grf lidar
* Serial Drive is working, need to work out distance publish
* WIP Getting Range Data in cm
* Working Rand Distance Values for GRF 250 and GRF500
* Review Changes
* Compiler fixes
* Update to date
* small update
* Fix typo and remover unused libs
* removing unused enum
* Update to the Documentation
* Fiving scaling issue
* update to the logic
* [Feature] Adding I2C driver for the GRF250 and GRF500 models (#26425)
* Adding the GRF I2C driver
* I2C Driver Working
* Removing a lot of unnecessary code
* fixing names
* Changing the i2c Driver to be in the lightware laser
* remove the old driver
* formatting fix
* Adding Ligthware GRF to documentation
* Update to the Documentation
* Ensuring sample_perf ends
* Updating Docs
* uavcannode: implement hardpoint commands (#26334)
* implement cannode hardpoint commands
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
* Update src/drivers/uavcannode/Subscribers/HardpointCommand.hpp
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* Update src/drivers/uavcannode/Subscribers/HardpointCommand.hpp
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* add hardpoint sub to ark cannode, simplify handling of hardpoint broadcast
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
---------
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* voxl_esc: Limit frequency of UART passthru writes to 20Hz
* voxl2_io: Added UART passthru
* docs: update link for px4 ros2 interface lib python api docs
* estimator_interface: remove unused getter
* gnss_checks: always run strict checks on ground
With the goal to never take off if the GNSS solution is not fullfilling the configured requirements still not stopping to use it in case it degrades mid air.
* ekf2 unit-tests: adapt to strict GNSS checks on ground
* escCheck: rework online check to properly report offline ESCs
previous to this
09d79b221f
set `esc_online_flags` e.g. for UAVCAN ESCs which specific one is online and that then got compared to a mask where the first `esc_count` bits were set.
So if only ESC 5 is mapped and online you get the message "ESC 156 offline" because `esc_online_flags = 0b1000` gets compared to `online_bitmask = 0b1` based on `esc_count = 1` and the motor index is `esc[0].actuator_function = 0` wrapped using `0 - actuator_motors_s::ACTUATOR_FUNCTION_MOTOR1 + 1 = 156`.
* FailureDetector: consistent timestamp naming
* FailureDetector: rework motor status check
* FailureDetector: implement upper and lower current limit with offset
* Update src/modules/commander/failure_detector/FailureDetector.cpp
Prevent Buffer overflow
* Update Format
* Subedit
* Shrink and rename image
* Apply suggestion from @hamishwillee
Sounds good
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* Apply suggestion from @hamishwillee
More universal approach
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* Update to the Documentation
* FailureDetector: rework motor status check
* FailureDetector: implement upper and lower current limit with offset
* Subedit
* docs: update parameter reference metadata
* Remove pregenerated files - that should all be tidied up next time this runs
* remover GRF parameters
* Documentation updates
* Fixing Merge Conflicts
* remove @
* Undo Changes to parameter_reference
* remove the code that will be autogen-ed
* Update the Camake File
---------
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
Co-authored-by: Andrew Brahim <35986980+dirksavage88@users.noreply.github.com>
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
Co-authored-by: Eric Katzfey <eric.katzfey@modalai.com>
Co-authored-by: Beat Küng <beat-kueng@gmx.net>
Co-authored-by: Matthias Grob <maetugr@gmail.com>
Co-authored-by: Marco Hauswirth <marco.hauswirth@auterion.com>
Co-authored-by: Nick <145654544+ttechnick@users.noreply.github.com>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Co-authored-by: Ramon Roche <mrpollo@gmail.com>
* Add new INS driver sbgECom
Implement sbgECom messages handling to provide IMU sensors, GNSS and EKF data to the autopilot
Be able to parametrize the serial port, baudrate and the communicating mode
Clone sbgECom library only if sbgecom support is enabled and apply a patch
Be able to send SBG Systems INS settings in several ways when starting sbgecom driver
* Fix sensor airspeed simulator units
* Fix HIGHRES_IMU pressure unit
* Allow HIGHRES_IMU to support 4 IMUs
* sbgECom: Add documentation
* Use submodule instead of fetching sbgECom using CMake
* Remove patch strategy
* Fix dates
* Remove patch file
* Update SBG dev type ID
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
---------
Co-authored-by: Samuel Toledano <samuel.toledano@sbg-systems.com>
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* Add vitepress tree
* Update existing workflows so they dont trigger on changes in the docs path
* Add nojekyll, package.json, LICENCE etc
* Add crowdin docs upload/download scripts
* Add docs flaw checker workflows
* Used docs prefix for docs workflows
* Crowdin obvious fixes
* ci: docs move to self hosted runner
runs on a beefy server for faster builds
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* ci: don't run build action for docs or ci changes
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* ci: update runners
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* Add docs/en
* Add docs assets and scripts
* Fix up editlinks to point to PX4 sources
* Download just the translations that are supported
* Add translation sources for zh, uk, ko
* Update latest tranlsation and uorb graphs
* update vitepress to latest
---------
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
Co-authored-by: Ramon Roche <mrpollo@gmail.com>
Peter C.
Hamish Willee
Aaron1356
Patrik Dominik Pordi
Eric Katzfey
patrikpordi
JoelJ18
Samuel Toledano
DATAGNSS
Seungbin Lee