694427e4ba
Converted commander to use px4_posix calls
...
Signed-off-by: Mark Charlebois <charlebm@gmail.com >
2015-04-20 11:37:50 -07:00
bba26c3430
Linux: enabled commander module
...
The commander module now compiles for Linux.
state_machine_helper_linux.cpp iterates over the virtual devices vs
all devices under /dev as per NuttX when disabling publishing.
Signed-off-by: Mark Charlebois <charlebm@gmail.com >
2015-04-20 11:37:50 -07:00
8ebf9755e4
commander: Fix battery config
2015-03-28 13:54:05 -07:00
49b3906b78
commander: Fix status checks for leds and adjust stack size based on actual use
2015-03-15 14:33:22 +01:00
dc522f217f
Commander: Fix GPS loss not handled properly
2015-02-11 16:42:01 +01:00
807cf7bd16
Commander: Implement calibration routines for multi-sensor setups
2015-02-09 22:56:23 +01:00
2d124852c1
propagate uorb contants change through all modules/drivers
2015-01-28 16:31:41 +01:00
c95de36d3a
commander: Add missing parameter definition
2014-07-20 19:42:31 +02:00
264fe884a2
Fixed load voltage calculation
2014-07-20 16:28:44 +02:00
3935540c7d
Set full voltage correctly to ensure percentage range fits. Force all users to new value by param renaming. Since this will tend to show batteries as more drained than before, this is a change in a safe direction and will not trigger unnoticed discharges.
2014-07-20 16:23:43 +02:00
3a0fc36c67
Consider the throttle load for battery voltage calculation
2014-07-19 14:12:33 +02:00
afc8908d38
commander: More docs-only changes in headers.
2014-07-13 11:45:32 +02:00
b1f223b468
commander: Default all leds to off
2014-06-24 22:22:56 +02:00
e5508a1aa0
Add Gumstix AeroCore device
...
Based on the work of Andrew Smith [1], add board configuration and device
drivers to support the Gumstix AeroCore (previously Aerodroid) board [2]. The
AeroCore is an autopilot board based on a STM32F427 similar to the FMUv2.
[1] https://github.com/smithandrewc/Firmware
[2] https://store.gumstix.com/index.php/products/585/
Signed-off-by: Ash Charles <ashcharles@gmail.com >
2014-05-13 09:41:41 -07:00
349809f535
sensors, commander: code style fixed
2014-05-11 13:36:51 +02:00
1dfa2f100e
commander: Stop mixing board support and high level code - just accept that non-mandatory leds may or may not be there
2014-04-30 15:33:47 +02:00
0ead560059
commander: tunes cleanup and fixes
2014-02-11 18:24:20 +01:00
855944fb2e
commander: beeps and blinks cleanup
2014-02-11 16:35:05 +01:00
6631ecf04a
commander: reset blink_msg_end when blink message completed to set normal LED status immediately
2014-02-11 16:35:05 +01:00
c1d1d67534
Improved RC calibration behaviour, fully supported setting trim offsets
2014-02-01 13:22:52 +01:00
714f5ea634
Track raw battery voltage and filtered battery voltage separately. Estimate remaining battery as min(voltage_estimate, discharged_estimate). Battery voltage LPF time increased.
2013-11-11 22:02:55 +04:00
6b085e8ced
Use discharged current to estimate remaining battery charge if capacity is known
2013-11-08 21:30:10 +04:00
2362041dc1
commander: state indication changed, 3 green blinks = succsess, 3 white blinks = neutral, 3 red blinks = reject
2013-09-19 19:58:41 +02:00
1a641b791d
tone_alarm: more device paths replaced with #define
2013-09-16 07:21:16 +02:00
efca6f2cb1
Remove unused tones and save about 6K flash space
...
- Comment out unused tones
- Create symbolic tone numbers rather than hardcoded
2013-08-30 20:12:35 -04:00
451adf2aa0
Added part of RGBLED stuff to commander
2013-08-16 18:05:59 +02:00
d75c3c4e73
Try to open RGBLEDs in commander (WIP)
2013-08-15 17:48:28 +02:00
02d4480e8e
commander rewrite almost completed, WIP
2013-07-31 20:58:27 +04:00
68ab69de01
moved commander to C++, preparation for better gyro scale calibration respecting the current attitude for more accurate results
2013-07-20 13:47:51 +02:00
Mark Charlebois
Lorenz Meier
Johan Jansen
Thomas Gubler
Ash Charles
Anton Babushkin
Randy Mackay
Jean Cyr
Julian Oes