boards: add new board X-MAV AP-H743r1 (#25967)

Author: @TompsonTan

.vscode/cmake-variants.yaml

@@ -531,3 +531,13 @@ CONFIG:
       buildType: MinSizeRel
       settings:
         CONFIG: svehicle_e2_default
+    x-mav_ap-h743r1_bootloader:
+      short: x-mav_ap-h743r1-boot
+      buildType: MinSizeRel
+      settings:
+        CONFIG: x-mav_ap-h743r1_bootloader
+    x-mav_ap-h743r1_default:
+      short: x-mav_ap-h743r1
+      buildType: MinSizeRel
+      settings:
+        CONFIG: x-mav_ap-h743r1_default

boards/x-mav/ap-h743r1/CMakeLists.txt

@@ -0,0 +1,34 @@
+############################################################################
+#
+#   Copyright (c) 2025 PX4 Development Team. All rights reserved.
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name PX4 nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+add_subdirectory(pwm_voltage)

boards/x-mav/ap-h743r1/bootloader.px4board

@@ -0,0 +1,4 @@
+CONFIG_BOARD_TOOLCHAIN="arm-none-eabi"
+CONFIG_BOARD_ARCHITECTURE="cortex-m7"
+CONFIG_BOARD_ROMFSROOT=""
+CONFIG_ARCH_CHIP_STM32H7=y

boards/x-mav/ap-h743r1/default.px4board

@@ -0,0 +1,92 @@
+CONFIG_BOARD_TOOLCHAIN="arm-none-eabi"
+CONFIG_BOARD_ARCHITECTURE="cortex-m7"
+CONFIG_BOARD_SERIAL_GPS1="/dev/ttyS0"
+CONFIG_BOARD_SERIAL_GPS2="/dev/ttyS1"
+CONFIG_BOARD_SERIAL_TEL1="/dev/ttyS2"
+CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS3"
+CONFIG_BOARD_SERIAL_TEL3="/dev/ttyS5"
+CONFIG_BOARD_SERIAL_TEL4="/dev/ttyS6"
+CONFIG_DRIVERS_ADC_BOARD_ADC=y
+CONFIG_DRIVERS_BAROMETER_DPS310=y
+CONFIG_DRIVERS_BAROMETER_GOERTEK_SPL06=y
+CONFIG_DRIVERS_CAMERA_CAPTURE=y
+CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_DRIVERS_CDCACM_AUTOSTART=y
+CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
+CONFIG_DRIVERS_DISTANCE_SENSOR_TF02PRO=y
+CONFIG_DRIVERS_DISTANCE_SENSOR_TFMINI=y
+CONFIG_DRIVERS_DSHOT=y
+CONFIG_DRIVERS_GPS=y
+CONFIG_DRIVERS_IMU_BOSCH_BMI270=y
+CONFIG_DRIVERS_IMU_INVENSENSE_ICM42688P=y
+CONFIG_DRIVERS_MAGNETOMETER_ISENTEK_IST8310=y
+CONFIG_DRIVERS_MAGNETOMETER_QMC5883L=y
+CONFIG_COMMON_OPTICAL_FLOW=y
+CONFIG_COMMON_OSD=y
+CONFIG_DRIVERS_PWM_OUT=y
+CONFIG_DRIVERS_PX4IO=y
+CONFIG_COMMON_RC=y
+CONFIG_COMMON_TELEMETRY=y
+CONFIG_DRIVERS_TONE_ALARM=y
+CONFIG_DRIVERS_UAVCAN=y
+CONFIG_BOARD_UAVCAN_TIMER_OVERRIDE=4
+CONFIG_MODULES_BATTERY_STATUS=y
+CONFIG_MODULES_CAMERA_FEEDBACK=y
+CONFIG_MODULES_COMMANDER=y
+CONFIG_MODULES_CONTROL_ALLOCATOR=y
+CONFIG_MODULES_DATAMAN=y
+CONFIG_MODULES_EKF2=y
+CONFIG_MODULES_EVENTS=y
+CONFIG_MODULES_FLIGHT_MODE_MANAGER=y
+CONFIG_MODULES_FW_ATT_CONTROL=y
+CONFIG_MODULES_FW_AUTOTUNE_ATTITUDE_CONTROL=y
+CONFIG_MODULES_FW_LATERAL_LONGITUDINAL_CONTROL=y
+CONFIG_MODULES_FW_MODE_MANAGER=y
+CONFIG_MODULES_FW_RATE_CONTROL=y
+CONFIG_MODULES_GIMBAL=y
+CONFIG_MODULES_GYRO_CALIBRATION=y
+CONFIG_MODULES_GYRO_FFT=y
+CONFIG_MODULES_LAND_DETECTOR=y
+CONFIG_MODULES_LANDING_TARGET_ESTIMATOR=y
+CONFIG_MODULES_LOAD_MON=y
+CONFIG_MODULES_LOCAL_POSITION_ESTIMATOR=y
+CONFIG_MODULES_LOGGER=y
+CONFIG_MODULES_MAG_BIAS_ESTIMATOR=y
+CONFIG_MODULES_MANUAL_CONTROL=y
+CONFIG_MODULES_MAVLINK=y
+CONFIG_MODULES_MC_ATT_CONTROL=y
+CONFIG_MODULES_MC_AUTOTUNE_ATTITUDE_CONTROL=y
+CONFIG_MODULES_MC_HOVER_THRUST_ESTIMATOR=y
+CONFIG_MODULES_MC_POS_CONTROL=y
+CONFIG_MODULES_MC_RATE_CONTROL=y
+CONFIG_MODULES_NAVIGATOR=y
+CONFIG_MODULES_RC_UPDATE=y
+CONFIG_MODULES_SENSORS=y
+CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
+CONFIG_MODULES_VTOL_ATT_CONTROL=y
+CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
+CONFIG_SYSTEMCMDS_BL_UPDATE=y
+CONFIG_SYSTEMCMDS_DMESG=y
+CONFIG_SYSTEMCMDS_DUMPFILE=y
+CONFIG_SYSTEMCMDS_GPIO=y
+CONFIG_SYSTEMCMDS_HARDFAULT_LOG=y
+CONFIG_SYSTEMCMDS_I2CDETECT=y
+CONFIG_SYSTEMCMDS_LED_CONTROL=y
+CONFIG_SYSTEMCMDS_MFT=y
+CONFIG_SYSTEMCMDS_MTD=y
+CONFIG_SYSTEMCMDS_NSHTERM=y
+CONFIG_SYSTEMCMDS_PARAM=y
+CONFIG_SYSTEMCMDS_PERF=y
+CONFIG_SYSTEMCMDS_REBOOT=y
+CONFIG_SYSTEMCMDS_SD_BENCH=y
+CONFIG_SYSTEMCMDS_SD_STRESS=y
+CONFIG_SYSTEMCMDS_SYSTEM_TIME=y
+CONFIG_SYSTEMCMDS_TOP=y
+CONFIG_SYSTEMCMDS_TOPIC_LISTENER=y
+CONFIG_SYSTEMCMDS_TUNE_CONTROL=y
+CONFIG_SYSTEMCMDS_UORB=y
+CONFIG_SYSTEMCMDS_USB_CONNECTED=y
+CONFIG_SYSTEMCMDS_VER=y
+CONFIG_SYSTEMCMDS_WORK_QUEUE=y
+CONFIG_EXAMPLES_FAKE_GPS=y
+CONFIG_ARCH_CHIP_STM32H7=y

boards/x-mav/ap-h743r1/firmware.prototype

@@ -0,0 +1,13 @@
+{
+    "board_id": 1203,
+    "magic": "PX4FWv1",
+    "description": "Firmware for the AP-H743r1 board",
+    "image": "",
+    "build_time": 0,
+    "summary": "AP-H743r1",
+    "version": "0.1",
+    "image_size": 0,
+    "image_maxsize": 1966080,
+    "git_identity": "",
+    "board_revision": 0
+}

boards/x-mav/ap-h743r1/init/rc.board_defaults

@@ -0,0 +1,29 @@
+#!/bin/sh
+#
+# board specific defaults
+#------------------------------------------------------------------------------
+param set-default BAT1_A_PER_V 17
+param set-default BAT1_N_CELLS 4
+param set-default BAT1_V_CHARGED 4.2
+param set-default BAT1_V_DIV 10.1
+param set-default BAT1_V_EMPTY 3.2
+
+param set-default SYS_HAS_MAG 1
+param set-default PWM_MAIN_TIM0 -4
+param set-default RC_INPUT_PROTO -1
+
+param set-default IMU_GYRO_RATEMAX 2000
+param set-default SYS_AUTOSTART 4001
+param set-default MC_PITCHRATE_K 0.4
+param set-default MC_ROLLRATE_K 0.35
+param set-default MC_YAWRATE_K 1.2
+param set-default MC_YAWRATE_MAX 360
+param set-default MAV_TYPE 2
+param set-default CA_AIRFRAME 0
+param set-default CA_ROTOR_COUNT 4
+param set-default CBRK_SUPPLY_CHK 894281
+
+param set-default USB_MAV_MODE 5
+
+# pwm voltage 3.3V/5V switch
+pwm_voltage_apply start

boards/x-mav/ap-h743r1/init/rc.board_extras

@@ -0,0 +1,4 @@
+#!/bin/sh
+#
+# board specific extras init
+#------------------------------------------------------------------------------

boards/x-mav/ap-h743r1/init/rc.board_sensors

@@ -0,0 +1,26 @@
+#!/bin/sh
+#
+# board specific sensors init
+#------------------------------------------------------------------------------
+
+board_adc start
+
+# IMU
+if ! icm42688p -s -b 1 -R 4 start
+then
+	bmi270 -s -b 1 -R 4 start
+fi
+
+if ! icm42688p -s -b 4 -R 4 start
+then
+	bmi270 -s -b 4 -R 4 start
+fi
+
+# baro
+if ! dps310 -I start -a 0x76
+then
+	spl06 -I  start -a 0x76
+fi
+
+# internal mag
+ist8310 -I -R 6 start

boards/x-mav/ap-h743r1/nuttx-config/Kconfig

@@ -0,0 +1,17 @@
+#
+# For a description of the syntax of this configuration file,
+# see misc/tools/kconfig-language.txt.
+#
+config BOARD_HAS_PROBES
+	bool "Board provides GPIO or other Hardware for signaling to timing analyze."
+	default y
+	---help---
+		This board provides GPIO FMU-CH1-5, CAP1-6 as PROBE_1-11 to provide timing signals from selected drivers.
+
+config BOARD_USE_PROBES
+	bool "Enable the use the board provided FMU-CH1-5, CAP1-6 as PROBE_1-11"
+	default n
+	depends on BOARD_HAS_PROBES
+
+	---help---
+		Select to use GPIO FMU-CH1-5, CAP1-6  to provide timing signals from selected drivers.

boards/x-mav/ap-h743r1/nuttx-config/bootloader/defconfig

@@ -0,0 +1,90 @@
+#
+# This file is autogenerated: PLEASE DO NOT EDIT IT.
+#
+# You can use "make menuconfig" to make any modifications to the installed .config file.
+# You can then do "make savedefconfig" to generate a new defconfig file that includes your
+# modifications.
+#
+# CONFIG_DEV_CONSOLE is not set
+# CONFIG_DISABLE_PSEUDOFS_OPERATIONS is not set
+# CONFIG_SPI_EXCHANGE is not set
+# CONFIG_STM32H7_SYSCFG is not set
+CONFIG_ARCH="arm"
+CONFIG_ARCH_BOARD_CUSTOM=y
+CONFIG_ARCH_BOARD_CUSTOM_DIR="../../../../boards/x-mav/ap-h743r1/nuttx-config"
+CONFIG_ARCH_BOARD_CUSTOM_DIR_RELPATH=y
+CONFIG_ARCH_BOARD_CUSTOM_NAME="px4"
+CONFIG_ARCH_CHIP="stm32h7"
+CONFIG_ARCH_CHIP_STM32H743VI=y
+CONFIG_ARCH_CHIP_STM32H7=y
+CONFIG_ARCH_INTERRUPTSTACK=768
+CONFIG_ARMV7M_BASEPRI_WAR=y
+CONFIG_ARMV7M_ICACHE=y
+CONFIG_ARMV7M_MEMCPY=y
+CONFIG_ARMV7M_USEBASEPRI=y
+CONFIG_BOARDCTL=y
+CONFIG_BOARDCTL_RESET=y
+CONFIG_BOARD_ASSERT_RESET_VALUE=0
+CONFIG_BOARD_INITTHREAD_PRIORITY=254
+CONFIG_BOARD_LATE_INITIALIZE=y
+CONFIG_BOARD_LOOPSPERMSEC=95150
+CONFIG_BOARD_RESET_ON_ASSERT=2
+CONFIG_CDCACM=y
+CONFIG_CDCACM_IFLOWCONTROL=y
+CONFIG_CDCACM_PRODUCTID=0x0036
+CONFIG_CDCACM_PRODUCTSTR="X-MAV AP-H743r1 Bootloader"
+CONFIG_CDCACM_RXBUFSIZE=600
+CONFIG_CDCACM_TXBUFSIZE=12000
+CONFIG_CDCACM_VENDORID=0x1B8C
+CONFIG_CDCACM_VENDORSTR="X-MAV"
+CONFIG_DEBUG_FULLOPT=y
+CONFIG_DEBUG_SYMBOLS=y
+CONFIG_DEBUG_TCBINFO=y
+CONFIG_DEFAULT_SMALL=y
+CONFIG_EXPERIMENTAL=y
+CONFIG_FDCLONE_DISABLE=y
+CONFIG_FDCLONE_STDIO=y
+CONFIG_HAVE_CXX=y
+CONFIG_HAVE_CXXINITIALIZE=y
+CONFIG_IDLETHREAD_STACKSIZE=750
+CONFIG_INIT_ENTRYPOINT="bootloader_main"
+CONFIG_INIT_STACKSIZE=3194
+CONFIG_LIBC_FLOATINGPOINT=y
+CONFIG_LIBC_LONG_LONG=y
+CONFIG_LIBC_STRERROR=y
+CONFIG_MEMSET_64BIT=y
+CONFIG_MEMSET_OPTSPEED=y
+CONFIG_PREALLOC_TIMERS=50
+CONFIG_PTHREAD_STACK_MIN=512
+CONFIG_RAM_SIZE=245760
+CONFIG_RAM_START=0x20010000
+CONFIG_RAW_BINARY=y
+CONFIG_SERIAL_TERMIOS=y
+CONFIG_SIG_DEFAULT=y
+CONFIG_SIG_SIGALRM_ACTION=y
+CONFIG_SIG_SIGUSR1_ACTION=y
+CONFIG_SIG_SIGUSR2_ACTION=y
+CONFIG_SPI=y
+CONFIG_STACK_COLORATION=y
+CONFIG_START_DAY=30
+CONFIG_START_MONTH=11
+CONFIG_STDIO_BUFFER_SIZE=32
+CONFIG_STM32H7_BKPSRAM=y
+CONFIG_STM32H7_DMA1=y
+CONFIG_STM32H7_OTGFS=y
+CONFIG_STM32H7_PROGMEM=y
+CONFIG_STM32H7_SERIAL_DISABLE_REORDERING=y
+CONFIG_STM32H7_TIM1=y
+CONFIG_STM32H7_USART6=y
+CONFIG_SYSTEMTICK_HOOK=y
+CONFIG_SYSTEM_CDCACM=y
+CONFIG_TASK_NAME_SIZE=24
+CONFIG_TTY_SIGINT=y
+CONFIG_TTY_SIGINT_CHAR=0x03
+CONFIG_TTY_SIGTSTP=y
+CONFIG_USART6_RXBUFSIZE=600
+CONFIG_USART6_TXBUFSIZE=300
+CONFIG_USBDEV=y
+CONFIG_USBDEV_BUSPOWERED=y
+CONFIG_USBDEV_MAXPOWER=500
+CONFIG_USEC_PER_TICK=1000

boards/x-mav/ap-h743r1/nuttx-config/include/board.h

@@ -0,0 +1,442 @@
+/************************************************************************************
+ * nuttx-configs/px4_fmu-v6u/include/board.h
+ *
+ *   Copyright (C) 2016-2019 Gregory Nutt. All rights reserved.
+ *   Authors: David Sidrane <david.sidrane@nscdg.com>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ************************************************************************************/
+#ifndef __NUTTX_CONFIG_APH743R1_INCLUDE_BOARD_H
+#define __NUTTX_CONFIG_APH743R1_INCLUDE_BOARD_H
+
+/************************************************************************************
+ * Included Files
+ ************************************************************************************/
+
+#include "board_dma_map.h"
+
+#include <nuttx/config.h>
+
+#ifndef __ASSEMBLY__
+# include <stdint.h>
+#endif
+
+#include "stm32_rcc.h"
+#include "stm32_sdmmc.h"
+
+/************************************************************************************
+ * Pre-processor Definitions
+ ************************************************************************************/
+
+/* Clocking *************************************************************************/
+/* The AP-H743 R1  board provides the following clock sources:
+ *
+ *   X1: 8 MHz crystal for HSE
+ *
+ * So we have these clock source available within the STM32
+ *
+ *   HSI: 16 MHz RC factory-trimmed
+ *   HSE: 16 MHz crystal for HSE
+ */
+
+#define STM32_BOARD_XTAL        8000000ul
+
+#define STM32_HSI_FREQUENCY     16000000ul
+#define STM32_LSI_FREQUENCY     32000
+#define STM32_HSE_FREQUENCY     STM32_BOARD_XTAL
+#define STM32_LSE_FREQUENCY     32768
+
+/* Main PLL Configuration.
+ *
+ * PLL source is HSE = 16,000,000
+ *
+ * PLL_VCOx = (STM32_HSE_FREQUENCY / PLLM) * PLLN
+ * Subject to:
+ *
+ *     1 <= PLLM <= 63
+ *     4 <= PLLN <= 512
+ *   150 MHz <= PLL_VCOL <= 420MHz
+ *   192 MHz <= PLL_VCOH <= 836MHz
+ *
+ * SYSCLK  = PLL_VCO / PLLP
+ * CPUCLK  = SYSCLK / D1CPRE
+ * Subject to
+ *
+ *   PLLP1   = {2, 4, 6, 8, ..., 128}
+ *   PLLP2,3 = {2, 3, 4, ..., 128}
+ *   CPUCLK <= 480 MHz
+ */
+
+#define STM32_BOARD_USEHSE
+
+#define STM32_PLLCFG_PLLSRC      RCC_PLLCKSELR_PLLSRC_HSE
+
+/* PLL1, wide 4 - 8 MHz input, enable DIVP, DIVQ, DIVR
+ *
+ *   PLL1_VCO = (8,000,000 / 1) * 120 = 960 MHz
+ *
+ *   PLL1P = PLL1_VCO/2  = 960 MHz / 2   = 480 MHz
+ *   PLL1Q = PLL1_VCO/4  = 960 MHz / 4   = 240 MHz
+ *   PLL1R = PLL1_VCO/8  = 960 MHz / 8   = 120 MHz
+ */
+
+#define STM32_PLLCFG_PLL1CFG    (RCC_PLLCFGR_PLL1VCOSEL_WIDE | \
+				 RCC_PLLCFGR_PLL1RGE_4_8_MHZ | \
+				 RCC_PLLCFGR_DIVP1EN | \
+				 RCC_PLLCFGR_DIVQ1EN | \
+				 RCC_PLLCFGR_DIVR1EN)
+#define STM32_PLLCFG_PLL1M       RCC_PLLCKSELR_DIVM1(1)
+#define STM32_PLLCFG_PLL1N       RCC_PLL1DIVR_N1(120)
+#define STM32_PLLCFG_PLL1P       RCC_PLL1DIVR_P1(2)
+#define STM32_PLLCFG_PLL1Q       RCC_PLL1DIVR_Q1(4)
+#define STM32_PLLCFG_PLL1R       RCC_PLL1DIVR_R1(8)
+
+#define STM32_VCO1_FREQUENCY     ((STM32_HSE_FREQUENCY / 1) * 120)
+#define STM32_PLL1P_FREQUENCY    (STM32_VCO1_FREQUENCY / 2)
+#define STM32_PLL1Q_FREQUENCY    (STM32_VCO1_FREQUENCY / 4)
+#define STM32_PLL1R_FREQUENCY    (STM32_VCO1_FREQUENCY / 8)
+
+/* PLL2 */
+
+#define STM32_PLLCFG_PLL2CFG     (RCC_PLLCFGR_PLL2VCOSEL_WIDE | \
+				  RCC_PLLCFGR_PLL2RGE_4_8_MHZ | \
+				  RCC_PLLCFGR_DIVP2EN | \
+				  RCC_PLLCFGR_DIVQ2EN | \
+				  RCC_PLLCFGR_DIVR2EN)
+#define STM32_PLLCFG_PLL2M       RCC_PLLCKSELR_DIVM2(2)
+#define STM32_PLLCFG_PLL2N       RCC_PLL2DIVR_N2(48)
+#define STM32_PLLCFG_PLL2P       RCC_PLL2DIVR_P2(2)
+#define STM32_PLLCFG_PLL2Q       RCC_PLL2DIVR_Q2(2)
+#define STM32_PLLCFG_PLL2R       RCC_PLL2DIVR_R2(2)
+
+#define STM32_VCO2_FREQUENCY     ((STM32_HSE_FREQUENCY / 2) * 48)
+#define STM32_PLL2P_FREQUENCY    (STM32_VCO2_FREQUENCY / 2)
+#define STM32_PLL2Q_FREQUENCY    (STM32_VCO2_FREQUENCY / 2)
+#define STM32_PLL2R_FREQUENCY    (STM32_VCO2_FREQUENCY / 2)
+
+/* PLL3 */
+
+#define STM32_PLLCFG_PLL3CFG    (RCC_PLLCFGR_PLL3VCOSEL_WIDE | \
+				 RCC_PLLCFGR_PLL3RGE_4_8_MHZ | \
+				 RCC_PLLCFGR_DIVQ3EN)
+#define STM32_PLLCFG_PLL3M      RCC_PLLCKSELR_DIVM3(2)
+#define STM32_PLLCFG_PLL3N      RCC_PLL3DIVR_N3(48)
+#define STM32_PLLCFG_PLL3P      RCC_PLL3DIVR_P3(2)
+#define STM32_PLLCFG_PLL3Q      RCC_PLL3DIVR_Q3(4)
+#define STM32_PLLCFG_PLL3R      RCC_PLL3DIVR_R3(2)
+
+#define STM32_VCO3_FREQUENCY    ((STM32_HSE_FREQUENCY / 2) * 48)
+#define STM32_PLL3P_FREQUENCY   (STM32_VCO3_FREQUENCY / 2)
+#define STM32_PLL3Q_FREQUENCY   (STM32_VCO3_FREQUENCY / 4)
+#define STM32_PLL3R_FREQUENCY   (STM32_VCO3_FREQUENCY / 2)
+
+/* SYSCLK = PLL1P = 480MHz
+ * CPUCLK = SYSCLK / 1 = 480 MHz
+ */
+
+#define STM32_RCC_D1CFGR_D1CPRE  (RCC_D1CFGR_D1CPRE_SYSCLK)
+#define STM32_SYSCLK_FREQUENCY   (STM32_PLL1P_FREQUENCY)
+#define STM32_CPUCLK_FREQUENCY   (STM32_SYSCLK_FREQUENCY / 1)
+
+/* Configure Clock Assignments */
+
+/* AHB clock (HCLK) is SYSCLK/2 (240 MHz max)
+ * HCLK1 = HCLK2 = HCLK3 = HCLK4 = 240
+ */
+
+#define STM32_RCC_D1CFGR_HPRE   RCC_D1CFGR_HPRE_SYSCLKd2        /* HCLK  = SYSCLK / 2 */
+#define STM32_ACLK_FREQUENCY    (STM32_CPUCLK_FREQUENCY / 2)    /* ACLK in D1, HCLK3 in D1 */
+#define STM32_HCLK_FREQUENCY    (STM32_CPUCLK_FREQUENCY / 2)    /* HCLK in D2, HCLK4 in D3 */
+#define STM32_BOARD_HCLK        STM32_HCLK_FREQUENCY            /* same as above, to satisfy compiler */
+
+/* APB1 clock (PCLK1) is HCLK/2 (120 MHz) */
+
+#define STM32_RCC_D2CFGR_D2PPRE1  RCC_D2CFGR_D2PPRE1_HCLKd2       /* PCLK1 = HCLK / 2 */
+#define STM32_PCLK1_FREQUENCY     (STM32_HCLK_FREQUENCY/2)
+
+/* APB2 clock (PCLK2) is HCLK/2 (120 MHz) */
+
+#define STM32_RCC_D2CFGR_D2PPRE2  RCC_D2CFGR_D2PPRE2_HCLKd2       /* PCLK2 = HCLK / 2 */
+#define STM32_PCLK2_FREQUENCY     (STM32_HCLK_FREQUENCY/2)
+
+/* APB3 clock (PCLK3) is HCLK/2 (120 MHz) */
+
+#define STM32_RCC_D1CFGR_D1PPRE   RCC_D1CFGR_D1PPRE_HCLKd2        /* PCLK3 = HCLK / 2 */
+#define STM32_PCLK3_FREQUENCY     (STM32_HCLK_FREQUENCY/2)
+
+/* APB4 clock (PCLK4) is HCLK/4 (120 MHz) */
+
+#define STM32_RCC_D3CFGR_D3PPRE   RCC_D3CFGR_D3PPRE_HCLKd2       /* PCLK4 = HCLK / 2 */
+#define STM32_PCLK4_FREQUENCY     (STM32_HCLK_FREQUENCY/2)
+
+/* Timer clock frequencies */
+
+/* Timers driven from APB1 will be twice PCLK1 */
+
+#define STM32_APB1_TIM2_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM3_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM4_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM5_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM6_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM7_CLKIN   (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM12_CLKIN  (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM13_CLKIN  (2*STM32_PCLK1_FREQUENCY)
+#define STM32_APB1_TIM14_CLKIN  (2*STM32_PCLK1_FREQUENCY)
+
+/* Timers driven from APB2 will be twice PCLK2 */
+
+#define STM32_APB2_TIM1_CLKIN   (2*STM32_PCLK2_FREQUENCY)
+#define STM32_APB2_TIM8_CLKIN   (2*STM32_PCLK2_FREQUENCY)
+#define STM32_APB2_TIM15_CLKIN  (2*STM32_PCLK2_FREQUENCY)
+#define STM32_APB2_TIM16_CLKIN  (2*STM32_PCLK2_FREQUENCY)
+#define STM32_APB2_TIM17_CLKIN  (2*STM32_PCLK2_FREQUENCY)
+
+/* Kernel Clock Configuration
+ *
+ * Note: look at Table 54 in ST Manual
+ */
+
+/* I2C123 clock source */
+
+#define STM32_RCC_D2CCIP2R_I2C123SRC RCC_D2CCIP2R_I2C123SEL_HSI
+
+/* I2C4 clock source */
+
+#define STM32_RCC_D3CCIPR_I2C4SRC    RCC_D3CCIPR_I2C4SEL_HSI
+
+/* SPI123 clock source */
+
+#define STM32_RCC_D2CCIP1R_SPI123SRC RCC_D2CCIP1R_SPI123SEL_PLL2
+
+/* SPI45 clock source */
+
+#define STM32_RCC_D2CCIP1R_SPI45SRC  RCC_D2CCIP1R_SPI45SEL_PLL2
+
+/* SPI6 clock source */
+
+#define STM32_RCC_D3CCIPR_SPI6SRC    RCC_D3CCIPR_SPI6SEL_PLL2
+
+/* USB 1 and 2 clock source */
+
+#define STM32_RCC_D2CCIP2R_USBSRC    RCC_D2CCIP2R_USBSEL_PLL3
+
+/* ADC 1 2 3 clock source */
+
+#define STM32_RCC_D3CCIPR_ADCSEL     RCC_D3CCIPR_ADCSEL_PLL2
+
+/* FDCAN 1 clock source */
+
+// #define STM32_RCC_D2CCIP1R_FDCANSEL  RCC_D2CCIP1R_FDCANSEL_HSE   /* FDCAN 1 2 clock source */
+
+#define STM32_FDCANCLK               STM32_HSE_FREQUENCY
+
+/* FLASH wait states
+ *
+ *  ------------ ---------- -----------
+ *  Vcore        MAX ACLK   WAIT STATES
+ *  ------------ ---------- -----------
+ *  1.15-1.26 V     70 MHz    0
+ *  (VOS1 level)   140 MHz    1
+ *                 210 MHz    2
+ *  1.05-1.15 V     55 MHz    0
+ *  (VOS2 level)   110 MHz    1
+ *                 165 MHz    2
+ *                 220 MHz    3
+ *  0.95-1.05 V     45 MHz    0
+ *  (VOS3 level)    90 MHz    1
+ *                 135 MHz    2
+ *                 180 MHz    3
+ *                 225 MHz    4
+ *  ------------ ---------- -----------
+ */
+
+#define BOARD_FLASH_WAITSTATES 2
+
+/* SDMMC definitions ********************************************************/
+
+/* Init 400kHz, freq = PLL1Q/(2*div)  div =  PLL1Q/(2*freq) */
+
+#define STM32_SDMMC_INIT_CLKDIV     (300 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
+
+/* 25 MHz Max for now, 25 mHZ = PLL1Q/(2*div), div =  PLL1Q/(2*freq)
+ * div = 4.8 = 240 / 50, So round up to 5 for default speed 24 MB/s
+ */
+
+#if defined(CONFIG_STM32H7_SDMMC_XDMA) || defined(CONFIG_STM32H7_SDMMC_IDMA)
+#  define STM32_SDMMC_MMCXFR_CLKDIV   (5 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
+#else
+#  define STM32_SDMMC_MMCXFR_CLKDIV   (100 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
+#endif
+#if defined(CONFIG_STM32H7_SDMMC_XDMA) || defined(CONFIG_STM32H7_SDMMC_IDMA)
+#  define STM32_SDMMC_SDXFR_CLKDIV    (5 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
+#else
+#  define STM32_SDMMC_SDXFR_CLKDIV    (100 << STM32_SDMMC_CLKCR_CLKDIV_SHIFT)
+#endif
+
+#define STM32_SDMMC_CLKCR_EDGE      STM32_SDMMC_CLKCR_NEGEDGE
+
+/* LED definitions ******************************************************************/
+/* The board has two, LED_GREEN a Green LED and LED_BLUE a Blue LED,
+ * that can be controlled by software.
+ *
+ * If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in any way.
+ * The following definitions are used to access individual LEDs.
+ */
+
+/* LED index values for use with board_userled() */
+
+#define BOARD_LED1        0
+#define BOARD_LED2        1
+#define BOARD_LED3        2
+#define BOARD_NLEDS       3
+
+#define BOARD_LED_RED     BOARD_LED1
+#define BOARD_LED_GREEN   BOARD_LED2
+#define BOARD_LED_BLUE    BOARD_LED3
+
+/* LED bits for use with board_userled_all() */
+
+#define BOARD_LED1_BIT    (1 << BOARD_LED1)
+#define BOARD_LED2_BIT    (1 << BOARD_LED2)
+#define BOARD_LED3_BIT    (1 << BOARD_LED3)
+
+/* If CONFIG_ARCH_LEDS is defined, the usage by the board port is defined in
+ * include/board.h and src/stm32_leds.c. The LEDs are used to encode OS-related
+ * events as follows:
+ *
+ *
+ *   SYMBOL                     Meaning                      LED state
+ *                                                        Red   Green Blue
+ *   ----------------------  --------------------------  ------ ------ ----*/
+
+#define LED_STARTED        0 /* NuttX has been started   OFF    OFF   OFF  */
+#define LED_HEAPALLOCATE   1 /* Heap has been allocated  OFF    OFF   ON   */
+#define LED_IRQSENABLED    2 /* Interrupts enabled       OFF    ON    OFF  */
+#define LED_STACKCREATED   3 /* Idle stack created       OFF    ON    ON   */
+#define LED_INIRQ          4 /* In an interrupt          N/C    N/C   GLOW */
+#define LED_SIGNAL         5 /* In a signal handler      N/C    GLOW  N/C  */
+#define LED_ASSERTION      6 /* An assertion failed      GLOW   N/C   GLOW */
+#define LED_PANIC          7 /* The system has crashed   Blink  OFF   N/C  */
+#define LED_IDLE           8 /* MCU is is sleep mode     ON     OFF   OFF  */
+
+/* Thus if the Green LED is statically on, NuttX has successfully booted and
+ * is, apparently, running normally.  If the Red LED is flashing at
+ * approximately 2Hz, then a fatal error has been detected and the system
+ * has halted.
+ */
+
+/* Alternate function pin selections ************************************************/
+
+#define GPIO_USART1_RX   GPIO_USART1_RX_2     	/* PA10 */
+#define GPIO_USART1_TX   GPIO_USART1_TX_2      	/* PA9 */
+
+#define GPIO_USART2_RX   GPIO_USART2_RX_2       /* PD6 */
+#define GPIO_USART2_TX   GPIO_USART2_TX_2       /* PD5 */
+
+#define GPIO_USART3_RX   GPIO_USART3_RX_3   	/* PD9 */
+#define GPIO_USART3_TX   GPIO_USART3_TX_3   	/* PD8 */
+
+#define GPIO_UART4_RX    GPIO_UART4_RX_3    	/* PB8 */
+#define GPIO_UART4_TX    GPIO_UART4_TX_3    	/* PB9 */
+
+#define GPIO_USART6_RX   GPIO_USART6_RX_1   	/* PC7 */
+#define GPIO_USART6_TX   GPIO_USART6_TX_1   	/* PC6 */
+
+#define GPIO_UART7_RX    GPIO_UART7_RX_3    	/* PE7 */
+#define GPIO_UART7_TX    GPIO_UART7_TX_3    	/* PE8 */
+
+#define GPIO_UART8_RX    GPIO_UART8_RX_1    	/* PE0 */
+#define GPIO_UART8_TX    GPIO_UART8_TX_1    	/* PE1 */
+
+/* SPI
+ *
+ */
+#define ADJ_SLEW_RATE(p) (((p) & ~GPIO_SPEED_MASK) | (GPIO_SPEED_2MHz))
+
+#define GPIO_SPI1_MISO   GPIO_SPI1_MISO_1               /* PA6  */
+#define GPIO_SPI1_MOSI   GPIO_SPI1_MOSI_1               /* PA7  */
+#define GPIO_SPI1_SCK    ADJ_SLEW_RATE(GPIO_SPI1_SCK_1) /* PA5 */
+
+#define GPIO_SPI3_MISO   GPIO_SPI3_MISO_2               /* PC11 */
+#define GPIO_SPI3_MOSI   GPIO_SPI3_MOSI_2               /* PC12 */
+#define GPIO_SPI3_SCK    ADJ_SLEW_RATE(GPIO_SPI3_SCK_2) /* PC10 */
+
+#define GPIO_SPI4_MISO   GPIO_SPI4_MISO_2               /* PE5 */
+#define GPIO_SPI4_MOSI   GPIO_SPI4_MOSI_2               /* PE6  */
+#define GPIO_SPI4_SCK    ADJ_SLEW_RATE(GPIO_SPI4_SCK_2) /* PE2 */
+
+/* I2C
+ *
+ */
+#define GPIO_I2C1_SCL GPIO_I2C1_SCL_1       /* PB6  */
+#define GPIO_I2C1_SDA GPIO_I2C1_SDA_1       /* PB7  */
+
+#define GPIO_I2C1_SCL_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_2MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN6)
+#define GPIO_I2C1_SDA_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_2MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN7)
+
+#define GPIO_I2C2_SCL GPIO_I2C2_SCL_1       /* PB10  */
+#define GPIO_I2C2_SDA GPIO_I2C2_SDA_1       /* PB11  */
+
+#define GPIO_I2C2_SCL_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_2MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN10)
+#define GPIO_I2C2_SDA_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_2MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN11)
+
+
+#define GPIO_I2C4_SCL GPIO_I2C4_SCL_1       /* PD12 */
+#define GPIO_I2C4_SDA GPIO_I2C4_SDA_1       /* PD13 */
+
+#define GPIO_I2C4_SCL_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_2MHz | GPIO_OUTPUT_SET | GPIO_PORTD | GPIO_PIN12)
+#define GPIO_I2C4_SDA_GPIO                  (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_2MHz | GPIO_OUTPUT_SET | GPIO_PORTD | GPIO_PIN13)
+
+#define GPIO_CAN1_RX     GPIO_CAN1_RX_3     /* PD0  */
+#define GPIO_CAN1_TX     GPIO_CAN1_TX_3     /* PD1  */
+
+#define GPIO_CAN2_RX     GPIO_CAN2_RX_1        /* PB12 */
+#define GPIO_CAN2_TX     GPIO_CAN2_TX_1        /* PB13 */
+
+/* SDMMC2
+ *
+ *      VDD 3.3
+ *      GND
+ *      SDMMC2_CK                           PD6
+ *      SDMMC2_CMD                          PD7
+ *      SDMMC2_D0                           PB14
+ *      SDMMC2_D1                           PB15
+ *      SDMMC2_D2                           PG11
+ *      SDMMC2_D3                           PB4
+ */
+
+#define GPIO_SDMMC2_CK   GPIO_SDMMC2_CK_2  /* PC1 */
+#define GPIO_SDMMC2_CMD  GPIO_SDMMC2_CMD_1 /* PD7 */
+// #define GPIO_SDMMC2_D0   GPIO_SDMMC2_D0    /* PB14 */
+// #define GPIO_SDMMC2_D1   GPIO_SDMMC2_D1    /* PB15 */
+#define GPIO_SDMMC2_D2   GPIO_SDMMC2_D2_2  /* PB3 */
+// #define GPIO_SDMMC2_D3   GPIO_SDMMC2_D3    /* PB4 */
+
+
+#endif  /*__NUTTX_CONFIG_APH743R1_INCLUDE_BOARD_H  */

boards/x-mav/ap-h743r1/nuttx-config/include/board_dma_map.h

@@ -0,0 +1,61 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+#pragma once
+
+// DMAMUX1 Using at most 8 Channels on DMA1 --------   Assigned
+//                                                     V
+
+#define DMAMAP_SPI1_RX    DMAMAP_DMA12_SPI1RX_0		/* 1 DMA1:37 IMU */
+#define DMAMAP_SPI1_TX    DMAMAP_DMA12_SPI1TX_0		/* 2 DMA1:38 IMU */
+
+#define DMAMAP_SPI2_RX    DMAMAP_DMA12_SPI2RX_0		/* DMA1:39 */
+#define DMAMAP_SPI2_TX    DMAMAP_DMA12_SPI2TX_0 	/* DMA1:40 */
+
+#define DMAMAP_SPI4_RX    DMAMAP_DMA12_SPI4RX_0		/* 3 DMA1:83 IMU */
+#define DMAMAP_SPI4_TX    DMAMAP_DMA12_SPI4TX_0		/* 4 DMA1:84 IMU */
+
+#define DMAMAP_USART1_RX  DMAMAP_DMA12_USART1RX_0	/*  DMA1:41  GPS1 */
+#define DMAMAP_USART1_TX  DMAMAP_DMA12_USART1TX_0	/*  DMA1:42  GPS1 */
+
+#define DMAMAP_USART2_RX  DMAMAP_DMA12_USART2RX_0	/*  DMA1:43 GPS2 */
+#define DMAMAP_USART2_TX  DMAMAP_DMA12_USART2TX_0	/*  DMA1:44 GPS2 */
+
+#define DMAMAP_USART3_RX  DMAMAP_DMA12_USART3RX_0	/*  DMA1:45 TELEM1 */
+#define DMAMAP_USART3_TX  DMAMAP_DMA12_USART3TX_0	/*  DMA1:46 TELEM1 */
+
+#define DMAMAP_UART4_RX    DMAMAP_DMA12_UART4RX_1	/*  DMA1:63 TELEM2 */
+#define DMAMAP_UART4_TX    DMAMAP_DMA12_UART4TX_1	/*  DMA1:64 TELEM2 */
+
+#define DMAMAP_USART6_RX  DMAMAP_DMA12_USART6RX_0	/*  DMA1:71 PX4IO */
+#define DMAMAP_USART6_TX  DMAMAP_DMA12_USART6TX_0	/*  DMA1:72 PX4IO */

boards/x-mav/ap-h743r1/nuttx-config/nsh/defconfig

@@ -0,0 +1,273 @@
+#
+# This file is autogenerated: PLEASE DO NOT EDIT IT.
+#
+# You can use "make menuconfig" to make any modifications to the installed .config file.
+# You can then do "make savedefconfig" to generate a new defconfig file that includes your
+# modifications.
+#
+# CONFIG_DISABLE_ENVIRON is not set
+# CONFIG_DISABLE_PSEUDOFS_OPERATIONS is not set
+# CONFIG_DISABLE_PTHREAD is not set
+# CONFIG_MMCSD_HAVE_CARDDETECT is not set
+# CONFIG_MMCSD_HAVE_WRITEPROTECT is not set
+# CONFIG_MMCSD_MMCSUPPORT is not set
+# CONFIG_MMCSD_SPI is not set
+# CONFIG_NSH_DISABLEBG is not set
+# CONFIG_NSH_DISABLESCRIPT is not set
+# CONFIG_NSH_DISABLE_CAT is not set
+# CONFIG_NSH_DISABLE_CD is not set
+# CONFIG_NSH_DISABLE_CP is not set
+# CONFIG_NSH_DISABLE_DATE is not set
+# CONFIG_NSH_DISABLE_DF is not set
+# CONFIG_NSH_DISABLE_ECHO is not set
+# CONFIG_NSH_DISABLE_ENV is not set
+# CONFIG_NSH_DISABLE_EXEC is not set
+# CONFIG_NSH_DISABLE_EXIT is not set
+# CONFIG_NSH_DISABLE_EXPORT is not set
+# CONFIG_NSH_DISABLE_FREE is not set
+# CONFIG_NSH_DISABLE_GET is not set
+# CONFIG_NSH_DISABLE_HELP is not set
+# CONFIG_NSH_DISABLE_ITEF is not set
+# CONFIG_NSH_DISABLE_KILL is not set
+# CONFIG_NSH_DISABLE_LOOPS is not set
+# CONFIG_NSH_DISABLE_LS is not set
+# CONFIG_NSH_DISABLE_MKDIR is not set
+# CONFIG_NSH_DISABLE_MKFATFS is not set
+# CONFIG_NSH_DISABLE_MOUNT is not set
+# CONFIG_NSH_DISABLE_MV is not set
+# CONFIG_NSH_DISABLE_PRINTF is not set
+# CONFIG_NSH_DISABLE_PS is not set
+# CONFIG_NSH_DISABLE_PSSTACKUSAGE is not set
+# CONFIG_NSH_DISABLE_PWD is not set
+# CONFIG_NSH_DISABLE_RM is not set
+# CONFIG_NSH_DISABLE_RMDIR is not set
+# CONFIG_NSH_DISABLE_SEMICOLON is not set
+# CONFIG_NSH_DISABLE_SET is not set
+# CONFIG_NSH_DISABLE_SLEEP is not set
+# CONFIG_NSH_DISABLE_SOURCE is not set
+# CONFIG_NSH_DISABLE_TEST is not set
+# CONFIG_NSH_DISABLE_TIME is not set
+# CONFIG_NSH_DISABLE_UMOUNT is not set
+# CONFIG_NSH_DISABLE_UNSET is not set
+# CONFIG_NSH_DISABLE_USLEEP is not set
+CONFIG_ARCH="arm"
+CONFIG_ARCH_BOARD_CUSTOM=y
+CONFIG_ARCH_BOARD_CUSTOM_DIR="../../../../boards/x-mav/ap-h743r1/nuttx-config"
+CONFIG_ARCH_BOARD_CUSTOM_DIR_RELPATH=y
+CONFIG_ARCH_BOARD_CUSTOM_NAME="px4"
+CONFIG_ARCH_CHIP="stm32h7"
+CONFIG_ARCH_CHIP_STM32H743VI=y
+CONFIG_ARCH_CHIP_STM32H7=y
+CONFIG_ARCH_INTERRUPTSTACK=768
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_ARMV7M_BASEPRI_WAR=y
+CONFIG_ARMV7M_DCACHE=y
+CONFIG_ARMV7M_DTCM=y
+CONFIG_ARMV7M_ICACHE=y
+CONFIG_ARMV7M_MEMCPY=y
+CONFIG_ARMV7M_USEBASEPRI=y
+CONFIG_ARM_MPU_EARLY_RESET=y
+CONFIG_BOARDCTL_RESET=y
+CONFIG_BOARD_ASSERT_RESET_VALUE=0
+CONFIG_BOARD_CRASHDUMP=y
+CONFIG_BOARD_LOOPSPERMSEC=95150
+CONFIG_BOARD_RESET_ON_ASSERT=2
+CONFIG_BUILTIN=y
+CONFIG_CDCACM=y
+CONFIG_CDCACM_IFLOWCONTROL=y
+CONFIG_CDCACM_PRODUCTID=0x0036
+CONFIG_CDCACM_PRODUCTSTR="X-MAV AP-H743r1"
+CONFIG_CDCACM_RXBUFSIZE=600
+CONFIG_CDCACM_TXBUFSIZE=12000
+CONFIG_CDCACM_VENDORID=0x1B8C
+CONFIG_CDCACM_VENDORSTR="X-MAV"
+CONFIG_DEBUG_FULLOPT=y
+CONFIG_DEBUG_HARDFAULT_ALERT=y
+CONFIG_DEBUG_MEMFAULT=y
+CONFIG_DEBUG_SYMBOLS=y
+CONFIG_DEFAULT_SMALL=y
+CONFIG_DEV_FIFO_SIZE=0
+CONFIG_DEV_PIPE_MAXSIZE=1024
+CONFIG_DEV_PIPE_SIZE=70
+CONFIG_EXPERIMENTAL=y
+CONFIG_FAT_DMAMEMORY=y
+CONFIG_FAT_LCNAMES=y
+CONFIG_FAT_LFN=y
+CONFIG_FAT_LFN_ALIAS_HASH=y
+CONFIG_FDCLONE_STDIO=y
+CONFIG_FS_BINFS=y
+CONFIG_FS_CROMFS=y
+CONFIG_FS_FAT=y
+CONFIG_FS_FATTIME=y
+CONFIG_FS_PROCFS=y
+CONFIG_FS_PROCFS_INCLUDE_PROGMEM=y
+CONFIG_FS_PROCFS_MAX_TASKS=64
+CONFIG_FS_PROCFS_REGISTER=y
+CONFIG_FS_ROMFS=y
+CONFIG_GRAN=y
+CONFIG_GRAN_INTR=y
+CONFIG_HAVE_CXX=y
+CONFIG_HAVE_CXXINITIALIZE=y
+CONFIG_I2C=y
+CONFIG_I2C_RESET=y
+CONFIG_IDLETHREAD_STACKSIZE=750
+CONFIG_INIT_ENTRYPOINT="nsh_main"
+CONFIG_INIT_STACKSIZE=3194
+CONFIG_IOB_NBUFFERS=24
+CONFIG_IOB_NCHAINS=24
+CONFIG_LIBC_FLOATINGPOINT=y
+CONFIG_LIBC_LONG_LONG=y
+CONFIG_LIBC_MAX_EXITFUNS=1
+CONFIG_LIBC_STRERROR=y
+CONFIG_MEMSET_64BIT=y
+CONFIG_MEMSET_OPTSPEED=y
+CONFIG_MMCSD=y
+CONFIG_MMCSD_SDIO=y
+CONFIG_MMCSD_SDIOWAIT_WRCOMPLETE=y
+CONFIG_MM_IOB=y
+CONFIG_MM_REGIONS=4
+CONFIG_MTD=y
+CONFIG_MTD_BYTE_WRITE=y
+CONFIG_MTD_PARTITION=y
+CONFIG_MTD_PROGMEM=y
+CONFIG_MTD_RAMTRON=y
+CONFIG_NAME_MAX=40
+CONFIG_NSH_ARCHINIT=y
+CONFIG_NSH_ARGCAT=y
+CONFIG_NSH_BUILTIN_APPS=y
+CONFIG_NSH_CMDPARMS=y
+CONFIG_NSH_CROMFSETC=y
+CONFIG_NSH_LINELEN=128
+CONFIG_NSH_MAXARGUMENTS=15
+CONFIG_NSH_NESTDEPTH=8
+CONFIG_NSH_QUOTE=y
+CONFIG_NSH_ROMFSETC=y
+CONFIG_NSH_ROMFSSECTSIZE=128
+CONFIG_NSH_STRERROR=y
+CONFIG_NSH_VARS=y
+CONFIG_OTG_ID_GPIO_DISABLE=y
+CONFIG_PIPES=y
+CONFIG_PREALLOC_TIMERS=50
+CONFIG_PRIORITY_INHERITANCE=y
+CONFIG_PTHREAD_MUTEX_ROBUST=y
+CONFIG_PTHREAD_STACK_MIN=512
+CONFIG_RAMTRON_SETSPEED=y
+CONFIG_RAM_SIZE=245760
+CONFIG_RAM_START=0x20010000
+CONFIG_RAW_BINARY=y
+CONFIG_READLINE_CMD_HISTORY=y
+CONFIG_READLINE_TABCOMPLETION=y
+CONFIG_RTC_DATETIME=y
+CONFIG_SCHED_HPWORK=y
+CONFIG_SCHED_HPWORKPRIORITY=249
+CONFIG_SCHED_HPWORKSTACKSIZE=1280
+CONFIG_SCHED_INSTRUMENTATION=y
+CONFIG_SCHED_INSTRUMENTATION_EXTERNAL=y
+CONFIG_SCHED_INSTRUMENTATION_SWITCH=y
+CONFIG_SCHED_LPWORK=y
+CONFIG_SCHED_LPWORKPRIORITY=50
+CONFIG_SCHED_LPWORKSTACKSIZE=1632
+CONFIG_SCHED_WAITPID=y
+CONFIG_SEM_PREALLOCHOLDERS=32
+CONFIG_SERIAL_IFLOWCONTROL_WATERMARKS=y
+CONFIG_SERIAL_TERMIOS=y
+CONFIG_SIG_DEFAULT=y
+CONFIG_SIG_SIGALRM_ACTION=y
+CONFIG_SIG_SIGUSR1_ACTION=y
+CONFIG_SIG_SIGUSR2_ACTION=y
+CONFIG_SIG_SIGWORK=4
+CONFIG_STACK_COLORATION=y
+CONFIG_START_DAY=30
+CONFIG_START_MONTH=11
+CONFIG_STDIO_BUFFER_SIZE=256
+CONFIG_STM32H7_ADC1=y
+CONFIG_STM32H7_ADC2=y
+CONFIG_STM32H7_ADC3=y
+CONFIG_STM32H7_BBSRAM=y
+CONFIG_STM32H7_BBSRAM_FILES=5
+CONFIG_STM32H7_BDMA=y
+CONFIG_STM32H7_BKPSRAM=y
+CONFIG_STM32H7_DMA1=y
+CONFIG_STM32H7_DMA2=y
+CONFIG_STM32H7_DMACAPABLE=y
+CONFIG_STM32H7_FLASH_OVERRIDE_I=y
+CONFIG_STM32H7_FLOWCONTROL_BROKEN=y
+CONFIG_STM32H7_I2C1=y
+CONFIG_STM32H7_I2C2=y
+CONFIG_STM32H7_I2C4=y
+CONFIG_STM32H7_I2C_DYNTIMEO=y
+CONFIG_STM32H7_I2C_DYNTIMEO_STARTSTOP=10
+CONFIG_STM32H7_OTGFS=y
+CONFIG_STM32H7_PROGMEM=y
+CONFIG_STM32H7_RTC=y
+CONFIG_STM32H7_RTC_HSECLOCK=y
+CONFIG_STM32H7_RTC_MAGIC_REG=1
+CONFIG_STM32H7_SAVE_CRASHDUMP=y
+CONFIG_STM32H7_SDMMC2=y
+CONFIG_STM32H7_SERIALBRK_BSDCOMPAT=y
+CONFIG_STM32H7_SERIAL_DISABLE_REORDERING=y
+CONFIG_STM32H7_SPI1=y
+CONFIG_STM32H7_SPI1_DMA=y
+CONFIG_STM32H7_SPI1_DMA_BUFFER=4096
+CONFIG_STM32H7_SPI3=y
+CONFIG_STM32H7_SPI4=y
+CONFIG_STM32H7_SPI4_DMA=y
+CONFIG_STM32H7_SPI4_DMA_BUFFER=4096
+CONFIG_STM32H7_SPI_DMATHRESHOLD=8
+CONFIG_STM32H7_TIM1=y
+CONFIG_STM32H7_TIM2=y
+CONFIG_STM32H7_TIM3=y
+CONFIG_STM32H7_TIM4=y
+CONFIG_STM32H7_TIM8=y
+CONFIG_STM32H7_UART4=y
+CONFIG_STM32H7_UART7=y
+CONFIG_STM32H7_UART8=y
+CONFIG_STM32H7_USART1=y
+CONFIG_STM32H7_USART2=y
+CONFIG_STM32H7_USART3=y
+CONFIG_STM32H7_USART6=y
+CONFIG_STM32H7_USART_BREAKS=y
+CONFIG_STM32H7_USART_INVERT=y
+CONFIG_STM32H7_USART_SINGLEWIRE=y
+CONFIG_STM32H7_USART_SWAP=y
+CONFIG_SYSTEM_CDCACM=y
+CONFIG_SYSTEM_NSH=y
+CONFIG_TASK_NAME_SIZE=24
+CONFIG_UART4_BAUD=921600
+CONFIG_UART4_RXBUFSIZE=3000
+CONFIG_UART4_RXDMA=y
+CONFIG_UART4_TXBUFSIZE=3000
+CONFIG_UART4_TXDMA=y
+CONFIG_UART7_BAUD=57600
+CONFIG_UART7_RXBUFSIZE=600
+CONFIG_UART7_TXBUFSIZE=3000
+CONFIG_UART8_BAUD=57600
+CONFIG_UART8_RXBUFSIZE=600
+CONFIG_UART8_SERIAL_CONSOLE=y
+CONFIG_UART8_TXBUFSIZE=3000
+CONFIG_USART1_BAUD=57600
+CONFIG_USART1_RXBUFSIZE=600
+CONFIG_USART1_RXDMA=y
+CONFIG_USART1_TXBUFSIZE=1500
+CONFIG_USART1_TXDMA=y
+CONFIG_USART2_BAUD=57600
+CONFIG_USART2_RXBUFSIZE=600
+CONFIG_USART2_RXDMA=y
+CONFIG_USART2_TXBUFSIZE=3000
+CONFIG_USART2_TXDMA=y
+CONFIG_USART3_BAUD=57600
+CONFIG_USART3_RXBUFSIZE=180
+CONFIG_USART3_RXDMA=y
+CONFIG_USART3_TXBUFSIZE=1500
+CONFIG_USART3_TXDMA=y
+CONFIG_USART6_BAUD=57600
+CONFIG_USART6_RXBUFSIZE=600
+CONFIG_USART6_RXDMA=y
+CONFIG_USART6_TXBUFSIZE=1500
+CONFIG_USART6_TXDMA=y
+CONFIG_USBDEV=y
+CONFIG_USBDEV_BUSPOWERED=y
+CONFIG_USBDEV_MAXPOWER=500
+CONFIG_USEC_PER_TICK=1000
+CONFIG_WATCHDOG=y
+CONFIG_WQUEUE_NOTIFIER=y

boards/x-mav/ap-h743r1/nuttx-config/scripts/bootloader_script.ld

@@ -0,0 +1,213 @@
+/****************************************************************************
+ * scripts/script.ld
+ *
+ *   Copyright (C) 2016, 2019 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The X-MAV AP-H743-R1 uses an STM32H743VIT6 has 2048Kb of main FLASH memory.
+ * The flash memory is partitioned into a User Flash memory and a System
+ * Flash memory. Each of these memories has two banks:
+ *
+ *   1) User Flash memory:
+ *
+ *      Bank 1: Start address 0x0800:0000 to 0x080F:FFFF with 8 sectors, 128Kb each
+ *      Bank 2: Start address 0x0810:0000 to 0x081F:FFFF with 8 sectors, 128Kb each
+ *
+ *   2) System Flash memory:
+ *
+ *      Bank 1: Start address 0x1FF0:0000 to 0x1FF1:FFFF with 1 x 128Kb sector
+ *      Bank 1: Start address 0x1FF4:0000 to 0x1FF5:FFFF with 1 x 128Kb sector
+ *
+ *   3) User option bytes for user configuration, only in Bank 1.
+ *
+ * In the STM32H743VIT6, two different boot spaces can be selected through
+ * the BOOT pin and the boot base address programmed in the BOOT_ADD0 and
+ * BOOT_ADD1 option bytes:
+ *
+ *   1) BOOT=0: Boot address defined by user option byte BOOT_ADD0[15:0].
+ *      ST programmed value: Flash memory at 0x0800:0000
+ *   2) BOOT=1: Boot address defined by user option byte BOOT_ADD1[15:0].
+ *      ST programmed value: System bootloader at 0x1FF0:0000
+ *
+ * The AP-H743-R1 has a Button on board, the BOOT0 pin is at ground so by default,
+ * the STM32 will boot to address 0x0800:0000 in FLASH unless the button has been pressed,
+ * then the boot will be from 0x1FF0:0000
+ *
+ * The STM32H743VIT6 also has 1024Kb of data SRAM.
+ * SRAM is split up into several blocks and into three power domains:
+ *
+ *   1) TCM SRAMs are dedicated to the Cortex-M7 and are accessible with
+ *      0 wait states by the Cortex-M7 and by MDMA through AHBS slave bus
+ *
+ *      1.1) 128Kb of DTCM-RAM beginning at address 0x2000:0000
+ *
+ *           The DTCM-RAM is organized as 2 x 64Kb DTCM-RAMs on 2 x 32 bit
+ *           DTCM ports. The DTCM-RAM could be used for critical real-time
+ *           data, such as interrupt service routines or stack / heap memory.
+ *           Both DTCM-RAMs can be used in parallel (for load/store operations)
+ *           thanks to the Cortex-M7 dual issue capability.
+ *
+ *      1.2)  64Kb of ITCM-RAM beginning at address 0x0000:0000
+ *
+ *           This RAM is connected to ITCM 64-bit interface designed for
+ *           execution of critical real-times routines by the CPU.
+ *
+ *   2) AXI SRAM (D1 domain) accessible by all system masters except BDMA
+ *      through D1 domain AXI bus matrix
+ *
+ *      2.1) 512Kb of SRAM beginning at address 0x2400:0000
+ *
+ *   3) AHB SRAM (D2 domain) accessible by all system masters except BDMA
+ *      through D2 domain AHB bus matrix
+ *
+ *      3.1) 128Kb of SRAM1 beginning at address 0x3000:0000
+ *      3.2) 128Kb of SRAM2 beginning at address 0x3002:0000
+ *      3.3)  32Kb of SRAM3 beginning at address 0x3004:0000
+ *
+ *      SRAM1 - SRAM3 are one contiguous block: 288Kb at address 0x3000:0000
+ *
+ *   4) AHB SRAM (D3 domain) accessible by most of system masters
+ *      through D3 domain AHB bus matrix
+ *
+ *      4.1)  64Kb of SRAM4 beginning at address 0x3800:0000
+ *      4.1)   4Kb of backup RAM beginning at address 0x3880:0000
+ *
+ * When booting from FLASH, FLASH memory is aliased to address 0x0000:0000
+ * where the code expects to begin execution by jumping to the entry point in
+ * the 0x0800:0000 address range.
+ */
+
+MEMORY
+{
+	itcm  (rwx) : ORIGIN = 0x00000000, LENGTH =   64K
+	flash (rx)  : ORIGIN = 0x08000000, LENGTH = 2048K
+	dtcm1 (rwx) : ORIGIN = 0x20000000, LENGTH =   64K
+	dtcm2 (rwx) : ORIGIN = 0x20010000, LENGTH =   64K
+	sram  (rwx) : ORIGIN = 0x24000000, LENGTH =  512K
+	sram1 (rwx) : ORIGIN = 0x30000000, LENGTH =  128K
+	sram2 (rwx) : ORIGIN = 0x30020000, LENGTH =  128K
+	sram3 (rwx) : ORIGIN = 0x30040000, LENGTH =   32K
+	sram4 (rwx) : ORIGIN = 0x38000000, LENGTH =   64K
+	bbram (rwx) : ORIGIN = 0x38800000, LENGTH =    4K
+}
+
+OUTPUT_ARCH(arm)
+EXTERN(_vectors)
+ENTRY(_stext)
+
+/*
+ * Ensure that abort() is present in the final object.  The exception handling
+ * code pulled in by libgcc.a requires it (and that code cannot be easily avoided).
+ */
+EXTERN(abort)
+EXTERN(_bootdelay_signature)
+
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		. = ALIGN(32);
+		/*
+		This signature provides the bootloader with a way to delay booting
+		*/
+		_bootdelay_signature = ABSOLUTE(.);
+		FILL(0xffecc2925d7d05c5)
+		. += 8;
+		*(.text .text.*)
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+
+	} > flash
+
+	/*
+	 * Init functions (static constructors and the like)
+	 */
+	.init_section : {
+		_sinit = ABSOLUTE(.);
+		KEEP(*(.init_array .init_array.*))
+		_einit = ABSOLUTE(.);
+	} > flash
+
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} > flash
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} > flash
+	__exidx_end = ABSOLUTE(.);
+
+	_eronly = ABSOLUTE(.);
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+	} > sram AT > flash
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		. = ALIGN(4);
+		_ebss = ABSOLUTE(.);
+	} > sram
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}

boards/x-mav/ap-h743r1/nuttx-config/scripts/script.ld

@@ -0,0 +1,228 @@
+/****************************************************************************
+ * scripts/script.ld
+ *
+ *   Copyright (C) 2020 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/* The board uses an STM32H743VIT6 and has 2048Kb of main FLASH memory.
+ * The flash memory is partitioned into a User Flash memory and a System
+ * Flash memory. Each of these memories has two banks:
+ *
+ *   1) User Flash memory:
+ *
+ *      Bank 1: Start address 0x0800:0000 to 0x080F:FFFF with 8 sectors, 128Kb each
+ *      Bank 2: Start address 0x0810:0000 to 0x081F:FFFF with 8 sectors, 128Kb each
+ *
+ *   2) System Flash memory:
+ *
+ *      Bank 1: Start address 0x1FF0:0000 to 0x1FF1:FFFF with 1 x 128Kb sector
+ *      Bank 1: Start address 0x1FF4:0000 to 0x1FF5:FFFF with 1 x 128Kb sector
+ *
+ *   3) User option bytes for user configuration, only in Bank 1.
+ *
+ * In the STM32H743VIT6, two different boot spaces can be selected through
+ * the BOOT pin and the boot base address programmed in the BOOT_ADD0 and
+ * BOOT_ADD1 option bytes:
+ *
+ *   1) BOOT=0: Boot address defined by user option byte BOOT_ADD0[15:0].
+ *      ST programmed value: Flash memory at 0x0800:0000
+ *   2) BOOT=1: Boot address defined by user option byte BOOT_ADD1[15:0].
+ *      ST programmed value: System bootloader at 0x1FF0:0000
+ *
+ * There's a button on board, the BOOT0 pin is at ground so by default,
+ * the STM32 will boot to address 0x0800:0000 in FLASH unless the switch is
+ * drepresed, then the boot will be from 0x1FF0:0000
+ *
+ * The STM32H743VIT6 also has 1024Kb of data SRAM.
+ * SRAM is split up into several blocks and into three power domains:
+ *
+ *   1) TCM SRAMs are dedicated to the Cortex-M7 and are accessible with
+ *      0 wait states by the Cortex-M7 and by MDMA through AHBS slave bus
+ *
+ *      1.1) 128Kb of DTCM-RAM beginning at address 0x2000:0000
+ *
+ *           The DTCM-RAM is organized as 2 x 64Kb DTCM-RAMs on 2 x 32 bit
+ *           DTCM ports. The DTCM-RAM could be used for critical real-time
+ *           data, such as interrupt service routines or stack / heap memory.
+ *           Both DTCM-RAMs can be used in parallel (for load/store operations)
+ *           thanks to the Cortex-M7 dual issue capability.
+ *
+ *      1.2)  64Kb of ITCM-RAM beginning at address 0x0000:0000
+ *
+ *           This RAM is connected to ITCM 64-bit interface designed for
+ *           execution of critical real-times routines by the CPU.
+ *
+ *   2) AXI SRAM (D1 domain) accessible by all system masters except BDMA
+ *      through D1 domain AXI bus matrix
+ *
+ *      2.1) 512Kb of SRAM beginning at address 0x2400:0000
+ *
+ *   3) AHB SRAM (D2 domain) accessible by all system masters except BDMA
+ *      through D2 domain AHB bus matrix
+ *
+ *      3.1) 128Kb of SRAM1 beginning at address 0x3000:0000
+ *      3.2) 128Kb of SRAM2 beginning at address 0x3002:0000
+ *      3.3)  32Kb of SRAM3 beginning at address 0x3004:0000
+ *
+ *      SRAM1 - SRAM3 are one contiguous block: 288Kb at address 0x3000:0000
+ *
+ *   4) AHB SRAM (D3 domain) accessible by most of system masters
+ *      through D3 domain AHB bus matrix
+ *
+ *      4.1)  64Kb of SRAM4 beginning at address 0x3800:0000
+ *      4.1)   4Kb of backup RAM beginning at address 0x3880:0000
+ *
+ * When booting from FLASH, FLASH memory is aliased to address 0x0000:0000
+ * where the code expects to begin execution by jumping to the entry point in
+ * the 0x0800:0000 address range.
+ */
+
+MEMORY
+{
+	ITCM_RAM  (rwx) : ORIGIN = 0x00000000, LENGTH =   64K
+	FLASH      (rx) : ORIGIN = 0x08020000, LENGTH = 1920K
+
+	DTCM1_RAM (rwx) : ORIGIN = 0x20000000, LENGTH =   64K
+	DTCM2_RAM (rwx) : ORIGIN = 0x20010000, LENGTH =   64K
+	AXI_SRAM  (rwx) : ORIGIN = 0x24000000, LENGTH =  512K /* D1 domain AXI bus */
+	SRAM1     (rwx) : ORIGIN = 0x30000000, LENGTH =  128K /* D2 domain AHB bus */
+	SRAM2     (rwx) : ORIGIN = 0x30020000, LENGTH =  128K /* D2 domain AHB bus */
+	SRAM3     (rwx) : ORIGIN = 0x30040000, LENGTH =   32K /* D2 domain AHB bus */
+	SRAM4     (rwx) : ORIGIN = 0x38000000, LENGTH =   64K /* D3 domain */
+	BKPRAM    (rwx) : ORIGIN = 0x38800000, LENGTH =    4K
+}
+
+OUTPUT_ARCH(arm)
+EXTERN(_vectors)
+ENTRY(_stext)
+
+/*
+ * Ensure that abort() is present in the final object.  The exception handling
+ * code pulled in by libgcc.a requires it (and that code cannot be easily avoided).
+ */
+EXTERN(abort)
+EXTERN(_bootdelay_signature)
+
+SECTIONS
+{
+	.text : {
+		_stext = ABSOLUTE(.);
+		*(.vectors)
+		. = ALIGN(32);
+		/*
+		This signature provides the bootloader with a way to delay booting
+		*/
+		_bootdelay_signature = ABSOLUTE(.);
+		FILL(0xffecc2925d7d05c5)
+		. += 8;
+		*(.text .text.*)
+		*(.fixup)
+		*(.gnu.warning)
+		*(.rodata .rodata.*)
+		*(.gnu.linkonce.t.*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.got)
+		*(.gcc_except_table)
+		*(.gnu.linkonce.r.*)
+		_etext = ABSOLUTE(.);
+
+	} > FLASH
+
+	/*
+	 * Init functions (static constructors and the like)
+	 */
+	.init_section : {
+		_sinit = ABSOLUTE(.);
+		KEEP(*(.init_array .init_array.*))
+		_einit = ABSOLUTE(.);
+	} > FLASH
+
+
+	.ARM.extab : {
+		*(.ARM.extab*)
+	} > FLASH
+
+	__exidx_start = ABSOLUTE(.);
+	.ARM.exidx : {
+		*(.ARM.exidx*)
+	} > FLASH
+	__exidx_end = ABSOLUTE(.);
+
+	_eronly = ABSOLUTE(.);
+
+	.data : {
+		_sdata = ABSOLUTE(.);
+		*(.data .data.*)
+		*(.gnu.linkonce.d.*)
+		CONSTRUCTORS
+		_edata = ABSOLUTE(.);
+
+		/* Pad out last section as the STM32H7 Flash write size is 256 bits. 32 bytes */
+		. = ALIGN(16);
+		FILL(0xffff)
+		. += 16;
+	} > AXI_SRAM AT > FLASH  = 0xffff
+
+	.bss : {
+		_sbss = ABSOLUTE(.);
+		*(.bss .bss.*)
+		*(.gnu.linkonce.b.*)
+		*(COMMON)
+		. = ALIGN(4);
+		_ebss = ABSOLUTE(.);
+	} > AXI_SRAM
+
+	/* Emit the the D3 power domain section for locating BDMA data */
+
+	.sram4_reserve (NOLOAD) :
+	{
+		*(.sram4)
+		. = ALIGN(4);
+		_sram4_heap_start = ABSOLUTE(.);
+	} > SRAM4
+
+	/* Stabs debugging sections. */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}

boards/x-mav/ap-h743r1/pwm_voltage/CMakeLists.txt

@@ -0,0 +1,42 @@
+############################################################################
+#
+#   Copyright (c) 2025 PX4 Development Team. All rights reserved.
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name PX4 nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+px4_add_module(
+	MODULE modules__pwm_voltage_apply
+	MAIN pwm_voltage_apply
+
+	SRCS
+		pwm_voltage.cpp
+	DEPENDS
+		px4_work_queue
+	)

boards/x-mav/ap-h743r1/pwm_voltage/parameters.c

@@ -0,0 +1,43 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2025 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * Control PWM output voltage
+ *
+ * @value 0 3.3V
+ * @value 1 5.0V
+ *
+ * @reboot_required true
+ * @group PWM Outputs
+ */
+PARAM_DEFINE_INT32(PWM_VOLT_SEL, 0);

boards/x-mav/ap-h743r1/pwm_voltage/pwm_voltage.cpp

@@ -0,0 +1,56 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2025 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+#include <inttypes.h>
+#include <stdint.h>
+
+#include <px4_platform_common/getopt.h>
+#include <px4_platform_common/module_params.h>
+
+#include "board_config.h"
+
+extern "C" int pwm_voltage_apply_main(int argc, char *argv[])
+{
+	int32_t pwm_volt_sel = 0;
+
+	param_get(param_find("PWM_VOLT_SEL"), &pwm_volt_sel);
+
+	if (pwm_volt_sel != 0) {
+		PWM_5V_VOLT_SEL(true);
+
+	} else {
+		PWM_5V_VOLT_SEL(false);
+	}
+
+	return 0;
+}

boards/x-mav/ap-h743r1/rover.px4board

@@ -0,0 +1,15 @@
+CONFIG_MODULES_FLIGHT_MODE_MANAGER=n
+CONFIG_MODULES_FW_ATT_CONTROL=n
+CONFIG_MODULES_FW_AUTOTUNE_ATTITUDE_CONTROL=n
+CONFIG_MODULES_FW_LATERAL_LONGITUDINAL_CONTROL=n
+CONFIG_MODULES_FW_MODE_MANAGER=n
+CONFIG_MODULES_FW_RATE_CONTROL=n
+CONFIG_MODULES_MC_ATT_CONTROL=n
+CONFIG_MODULES_MC_AUTOTUNE_ATTITUDE_CONTROL=n
+CONFIG_MODULES_MC_HOVER_THRUST_ESTIMATOR=n
+CONFIG_MODULES_MC_POS_CONTROL=n
+CONFIG_MODULES_MC_RATE_CONTROL=n
+CONFIG_MODULES_VTOL_ATT_CONTROL=n
+CONFIG_MODULES_ROVER_ACKERMANN=y
+CONFIG_MODULES_ROVER_DIFFERENTIAL=y
+CONFIG_MODULES_ROVER_MECANUM=y

boards/x-mav/ap-h743r1/src/CMakeLists.txt

@@ -0,0 +1,70 @@
+############################################################################
+#
+#   Copyright (c) 2021 PX4 Development Team. All rights reserved.
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name PX4 nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+if("${PX4_BOARD_LABEL}" STREQUAL  "bootloader")
+	add_library(drivers_board
+		bootloader_main.c
+		usb.c
+	)
+	target_link_libraries(drivers_board
+		PRIVATE
+			nuttx_arch
+			nuttx_drivers
+			bootloader
+	)
+	target_include_directories(drivers_board PRIVATE ${PX4_SOURCE_DIR}/platforms/nuttx/src/bootloader/common)
+
+else()
+	add_library(drivers_board
+		i2c.cpp
+		init.c
+		led.c
+		sdio.c
+		spi.cpp
+		timer_config.cpp
+		usb.c
+		mtd.cpp
+		can.c
+	)
+	# add_dependencies(drivers_board arch_board_hw_info)
+
+	target_link_libraries(drivers_board
+		PRIVATE
+			arch_io_pins
+			arch_spi
+			arch_board_hw_info
+			drivers__led
+			nuttx_arch
+			nuttx_drivers
+			px4_layer
+	)
+endif()

boards/x-mav/ap-h743r1/src/board_config.h

@@ -0,0 +1,226 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file board_config.h
+ *
+ * Board internal definitions
+ */
+
+#pragma once
+
+/****************************************************************************************************
+ * Included Files
+ ****************************************************************************************************/
+
+#include <px4_platform_common/px4_config.h>
+#include <nuttx/compiler.h>
+#include <stdint.h>
+
+#include <stm32_gpio.h>
+
+/****************************************************************************************************
+ * Definitions
+ ****************************************************************************************************/
+
+/* PX4IO connection configuration */
+#define BOARD_USES_PX4IO_VERSION       2
+#define PX4IO_SERIAL_DEVICE            "/dev/ttyS4"
+#define PX4IO_SERIAL_TX_GPIO           GPIO_USART6_TX
+#define PX4IO_SERIAL_RX_GPIO           GPIO_USART6_RX
+#define PX4IO_SERIAL_BASE              STM32_USART6_BASE
+#define PX4IO_SERIAL_VECTOR            STM32_IRQ_USART6
+#define PX4IO_SERIAL_TX_DMAMAP         DMAMAP_USART6_TX
+#define PX4IO_SERIAL_RX_DMAMAP         DMAMAP_USART6_RX
+#define PX4IO_SERIAL_RCC_REG           STM32_RCC_APB2ENR
+#define PX4IO_SERIAL_RCC_EN            RCC_APB2ENR_USART6EN
+#define PX4IO_SERIAL_CLOCK             STM32_PCLK2_FREQUENCY
+#define PX4IO_SERIAL_BITRATE           1500000               /* 1.5Mbps -> max rate for IO */
+
+/* LEDs are driven with push open drain to support Anode to 5V or 3.3V */
+
+#  define GPIO_nLED_RED         /* PD15 */  (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTD|GPIO_PIN15)
+#  define GPIO_nLED_GREEN       /* PD11 */  (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTD|GPIO_PIN11)
+#  define GPIO_nLED_BLUE        /* PD10 */  (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTD|GPIO_PIN10)
+
+#  define BOARD_HAS_CONTROL_STATUS_LEDS      1
+#  define BOARD_OVERLOAD_LED     LED_RED
+#  define BOARD_ARMED_STATE_LED  LED_BLUE
+
+/*
+ * ADC channels
+ *
+ * These are the channel numbers of the ADCs of the microcontroller that
+ * can be used by the Px4 Firmware in the adc driver
+ */
+
+/* ADC defines to be used in sensors.cpp to read from a particular channel */
+
+#define SYSTEM_ADC_BASE STM32_ADC1_BASE
+
+#define ADC12_CH(n)		(n)
+#define ADC3_CH(n)                  (n)
+
+#define ANALOG_PC3 (GPIO_ANALOG|GPIO_PORTC|GPIO_PIN3)
+
+#define PX4_ADC_GPIO  \
+	/* PC4  */  GPIO_ADC12_INP4,  \
+	/* PC5  */  GPIO_ADC12_INP8
+
+/* Define GPIO pins used as ADC N.B. Channel numbers must match below  */
+/* Define Channel numbers must match above GPIO pin IN(n)*/
+#define ADC_BATTERY_VOLTAGE_CHANNEL             ADC12_CH(4)
+#define ADC_BATTERY_CURRENT_CHANNEL             ADC12_CH(8)
+
+#define ADC_CHANNELS \
+	((1 << ADC_BATTERY_VOLTAGE_CHANNEL) | \
+	 (1 << ADC_BATTERY_CURRENT_CHANNEL))
+
+#define BOARD_ADC_OPEN_CIRCUIT_V     (1.6f)
+
+#define BOARD_HAS_STATIC_MANIFEST 1
+
+#define UAVCAN_NUM_IFACES_RUNTIME  1
+
+/* PWM
+ */
+#define DIRECT_PWM_OUTPUT_CHANNELS   7
+
+#define BOARD_HAS_PWM  DIRECT_PWM_OUTPUT_CHANNELS
+
+/* PWM Power */
+#define GPIO_PWM_VOLT_SEL               /* PA8  */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN8)
+#define PWM_5V_VOLT_SEL(on_true)        px4_arch_gpiowrite(GPIO_PWM_VOLT_SEL, (on_true))
+
+/* Tone alarm output */
+#define TONE_ALARM_TIMER        5 /* Timer 5 */
+#define TONE_ALARM_CHANNEL      4  /* PA3 GPIO_TIM5_CH4 */
+#define GPIO_BUZZER_1           /* PA3 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN3)
+
+#define GPIO_TONE_ALARM_IDLE    GPIO_BUZZER_1
+#define GPIO_TONE_ALARM         GPIO_BUZZER_1
+
+/* USB OTG FS
+ *
+ * PE15  OTG_FS_VBUS VBUS sensing
+ */
+#define GPIO_OTGFS_VBUS         /* PE15 */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_SPEED_100MHz|GPIO_PORTE|GPIO_PIN15)
+#define BOARD_ADC_USB_CONNECTED (px4_arch_gpioread(GPIO_OTGFS_VBUS))
+
+/* High-resolution timer */
+#define HRT_TIMER               8  /* use timer1 for the HRT */
+#define HRT_TIMER_CHANNEL       1  /* use capture/compare channel 1 */
+
+/* RC Serial port */
+#define RC_SERIAL_PORT                     "/dev/ttyS4"
+#define BOARD_SUPPORTS_RC_SERIAL_PORT_OUTPUT
+
+/* SD card bringup does not work if performed on the IDLE thread because it
+ * will cause waiting.  Use either:
+ *
+ *  CONFIG_LIB_BOARDCTL=y, OR
+ *  CONFIG_BOARD_INITIALIZE=y && CONFIG_BOARD_INITTHREAD=y
+ */
+#define SDIO_SLOTNO             0  /* Only one slot */
+#define SDIO_MINOR              0
+#if defined(CONFIG_BOARD_INITIALIZE) && !defined(CONFIG_LIB_BOARDCTL) && \
+   !defined(CONFIG_BOARD_INITTHREAD)
+#  warning SDIO initialization cannot be perfomed on the IDLE thread
+#endif
+
+/* This board provides a DMA pool and APIs */
+#define BOARD_DMA_ALLOC_POOL_SIZE 5120
+
+/* This board provides the board_on_reset interface */
+#define BOARD_HAS_ON_RESET 1
+
+#define PX4_GPIO_INIT_LIST { \
+		GPIO_CAN1_TX,\
+		GPIO_CAN1_RX,\
+		GPIO_CAN2_TX,\
+		GPIO_CAN2_RX,\
+		PX4_ADC_GPIO,\
+		GPIO_TONE_ALARM_IDLE,\
+		GPIO_PWM_VOLT_SEL\
+	}
+
+#define BOARD_ENABLE_CONSOLE_BUFFER
+
+#define BOARD_NUM_IO_TIMERS 5
+
+
+__BEGIN_DECLS
+
+/****************************************************************************************************
+ * Public Types
+ ****************************************************************************************************/
+
+/****************************************************************************************************
+ * Public data
+ ****************************************************************************************************/
+
+#ifndef __ASSEMBLY__
+
+/****************************************************************************************************
+ * Public Functions
+ ****************************************************************************************************/
+
+/****************************************************************************
+ * Name: stm32_sdio_initialize
+ *
+ * Description:
+ *   Initialize SDIO-based MMC/SD card support
+ *
+ ****************************************************************************/
+
+int stm32_sdio_initialize(void);
+
+/****************************************************************************************************
+ * Name: stm32_spiinitialize
+ *
+ * Description:
+ *   Called to configure SPI chip select GPIO pins for the board.
+ *
+ ****************************************************************************************************/
+
+extern void stm32_spiinitialize(void);
+
+extern void stm32_usbinitialize(void);
+
+extern void board_peripheral_reset(int ms);
+
+#include <px4_platform_common/board_common.h>
+
+#endif /* __ASSEMBLY__ */
+
+__END_DECLS

boards/x-mav/ap-h743r1/src/bootloader_main.c

@@ -0,0 +1,75 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file bootloader_main.c
+ *
+ * FMU-specific early startup code for bootloader
+*/
+
+#include "board_config.h"
+#include "bl.h"
+
+#include <nuttx/config.h>
+#include <nuttx/board.h>
+#include <chip.h>
+#include <stm32_uart.h>
+#include <arch/board/board.h>
+#include "arm_internal.h"
+#include <px4_platform_common/init.h>
+
+extern int sercon_main(int c, char **argv);
+
+__EXPORT void board_on_reset(int status) {}
+
+__EXPORT void stm32_boardinitialize(void)
+{
+	/* configure USB interfaces */
+	stm32_usbinitialize();
+}
+
+__EXPORT int board_app_initialize(uintptr_t arg)
+{
+	return 0;
+}
+
+void board_late_initialize(void)
+{
+	sercon_main(0, NULL);
+}
+
+extern void sys_tick_handler(void);
+void board_timerhook(void)
+{
+	sys_tick_handler();
+}

boards/x-mav/ap-h743r1/src/can.c

@@ -0,0 +1,140 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2012 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file px4fmu_can.c
+ *
+ * Board-specific CAN functions.
+ */
+
+#if !defined(CONFIG_CAN)
+
+#include <stdint.h>
+
+#include "board_config.h"
+
+
+__EXPORT
+uint16_t board_get_can_interfaces(void)
+{
+	uint16_t enabled_interfaces = 0x3;
+
+	enabled_interfaces &= ~(1 << 1);
+
+	return enabled_interfaces;
+}
+
+#else
+
+#include <errno.h>
+#include <debug.h>
+
+#include <nuttx/can/can.h>
+#include <arch/board/board.h>
+
+#include "chip.h"
+#include "arm_internal.h"
+
+#include "chip.h"
+#include "stm32_can.h"
+#include "board_config.h"
+
+/************************************************************************************
+ * Pre-processor Definitions
+ ************************************************************************************/
+/* Configuration ********************************************************************/
+
+#if defined(CONFIG_STM32_CAN1) && defined(CONFIG_STM32_CAN2)
+#  warning "Both CAN1 and CAN2 are enabled.  Assuming only CAN1."
+#  undef CONFIG_STM32_CAN2
+#endif
+
+#ifdef CONFIG_STM32_CAN1
+#  define CAN_PORT 1
+#else
+#  define CAN_PORT 2
+#endif
+
+/************************************************************************************
+ * Private Functions
+ ************************************************************************************/
+
+/************************************************************************************
+ * Public Functions
+ ************************************************************************************/
+int can_devinit(void);
+
+/************************************************************************************
+ * Name: can_devinit
+ *
+ * Description:
+ *   All STM32 architectures must provide the following interface to work with
+ *   examples/can.
+ *
+ ************************************************************************************/
+
+int can_devinit(void)
+{
+	static bool initialized = false;
+	struct can_dev_s *can;
+	int ret;
+
+	/* Check if we have already initialized */
+
+	if (!initialized) {
+		/* Call stm32_caninitialize() to get an instance of the CAN interface */
+
+		can = stm32_caninitialize(CAN_PORT);
+
+		if (can == NULL) {
+			canerr("ERROR:  Failed to get CAN interface\n");
+			return -ENODEV;
+		}
+
+		/* Register the CAN driver at "/dev/can0" */
+
+		ret = can_register("/dev/can0", can);
+
+		if (ret < 0) {
+			canerr("ERROR: can_register failed: %d\n", ret);
+			return ret;
+		}
+
+		/* Now we are initialized */
+
+		initialized = true;
+	}
+
+	return OK;
+}
+#endif /* CONFIG_CAN */

boards/x-mav/ap-h743r1/src/hw_config.h

@@ -0,0 +1,135 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+#pragma once
+
+/****************************************************************************
+ * 10-8--2016:
+ *  To simplify the ripple effect on the tools, we will be using
+ *  /dev/serial/by-id/<asterisk>PX4<asterisk> to locate PX4 devices. Therefore
+ *  moving forward all Bootloaders must contain the prefix "PX4 BL "
+ *  in the USBDEVICESTRING
+ *  This Change will be made in an upcoming BL release
+ ****************************************************************************/
+/*
+ * Define usage to configure a bootloader
+ *
+ *
+ * Constant                example          Usage
+ * APP_LOAD_ADDRESS     0x08004000            - The address in Linker Script, where the app fw is org-ed
+ * BOOTLOADER_DELAY     5000                  - Ms to wait while under USB pwr or bootloader request
+ * BOARD_FMUV2
+ * INTERFACE_USB        1                     - (Optional) Scan and use the USB interface for bootloading
+ * INTERFACE_USART      1                     - (Optional) Scan and use the Serial interface for bootloading
+ * USBDEVICESTRING      "PX4 BL FMU v2.x"     - USB id string
+ * USBPRODUCTID         0x0011                - PID Should match defconfig
+ * BOOT_DELAY_ADDRESS   0x000001a0            - (Optional) From the linker script from Linker Script to get a custom
+ *                                               delay provided by an APP FW
+ * BOARD_TYPE           9                     - Must match .prototype boad_id
+ * _FLASH_KBYTES        (*(uint16_t *)0x1fff7a22) - Run time flash size detection
+ * BOARD_FLASH_SECTORS  ((_FLASH_KBYTES == 0x400) ? 11 : 23) - Run time determine the physical last sector
+ * BOARD_FLASH_SECTORS   11                   - Hard coded zero based last sector
+ * BOARD_FLASH_SIZE     (_FLASH_KBYTES*1024)-   Total Flash size of device, determined at run time.
+ *                         (1024 * 1024)      - Hard coded Total Flash of device - The bootloader and app reserved will be deducted
+ *                                              programmatically
+ *
+ * BOARD_FIRST_FLASH_SECTOR_TO_ERASE  2        - Optional sectors index in the flash_sectors table  (F4 only), to begin erasing.
+ *                                               This is to allow sectors to be reserved for app fw usage. That will NOT be erased
+ *                                               during a FW upgrade.
+ *                                               The default is 0, and selects the first sector to be erased, as the 0th entry in the
+ *                                               flash_sectors table. Which is the second physical sector of FLASH in the device.
+ *                                               The first physical sector of FLASH is used by the bootloader, and is not defined
+ *                                               in the table.
+ *
+ * APP_RESERVATION_SIZE (BOARD_FIRST_FLASH_SECTOR_TO_ERASE * 16 * 1024) - Number of bytes reserved by the APP FW. This number plus
+ *                                                                        BOOTLOADER_RESERVATION_SIZE  will be deducted from
+ *                                                                        BOARD_FLASH_SIZE to determine the size of the App FW
+ *                                                                        and hence the address space of FLASH to erase and program.
+ * USBMFGSTRING            "PX4 AP"            - Optional USB MFG string (default is '3D Robotics' if not defined.)
+ * SERIAL_BREAK_DETECT_DISABLED                -  Optional prevent break selection on Serial port from entering or staying in BL
+ *
+ * * Other defines are somewhat self explanatory.
+ */
+
+/* Boot device selection list*/
+#define USB0_DEV       0x01
+#define SERIAL0_DEV    0x02
+#define SERIAL1_DEV    0x04
+
+#define APP_LOAD_ADDRESS               0x08020000
+#define BOOTLOADER_DELAY               5000
+#define INTERFACE_USB                  1
+#define INTERFACE_USB_CONFIG           "/dev/ttyACM0"
+#define BOARD_VBUS                     MK_GPIO_INPUT(GPIO_OTGFS_VBUS)
+
+//#define USE_VBUS_PULL_DOWN
+// #define INTERFACE_USART                6
+#define INTERFACE_USART_CONFIG         "/dev/ttyS5,57600"
+#define BOOT_DELAY_ADDRESS             0x000001a0
+#define BOARD_TYPE                     1203
+#define _FLASH_KBYTES                  (*(uint32_t *)0x1FF1E880)
+#define BOARD_FLASH_SECTORS            (15)
+#define BOARD_FLASH_SIZE               (_FLASH_KBYTES * 1024)
+
+#define OSC_FREQ                       8
+
+#define BOARD_PIN_LED_ACTIVITY         GPIO_nLED_BLUE // BLUE
+#define BOARD_PIN_LED_BOOTLOADER       GPIO_nLED_RED // RED
+#define BOARD_LED_ON                   1
+#define BOARD_LED_OFF                  0
+
+#define SERIAL_BREAK_DETECT_DISABLED   1
+
+#if !defined(ARCH_SN_MAX_LENGTH)
+# define ARCH_SN_MAX_LENGTH 12
+#endif
+
+#if !defined(APP_RESERVATION_SIZE)
+#  define APP_RESERVATION_SIZE 0
+#endif
+
+#if !defined(BOARD_FIRST_FLASH_SECTOR_TO_ERASE)
+#  define BOARD_FIRST_FLASH_SECTOR_TO_ERASE 1
+#endif
+
+#if !defined(USB_DATA_ALIGN)
+# define USB_DATA_ALIGN
+#endif
+
+#ifndef BOOT_DEVICES_SELECTION
+#  define BOOT_DEVICES_SELECTION USB0_DEV|SERIAL0_DEV|SERIAL1_DEV
+#endif
+
+#ifndef BOOT_DEVICES_FILTER_ONUSB
+#  define BOOT_DEVICES_FILTER_ONUSB USB0_DEV|SERIAL0_DEV|SERIAL1_DEV
+#endif

boards/x-mav/ap-h743r1/src/i2c.cpp

@@ -0,0 +1,40 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+#include <px4_arch/i2c_hw_description.h>
+
+constexpr px4_i2c_bus_t px4_i2c_buses[I2C_BUS_MAX_BUS_ITEMS] = {
+	initI2CBusInternal(1),
+	initI2CBusExternal(2),
+	initI2CBusExternal(4),
+};

boards/x-mav/ap-h743r1/src/init.c

@@ -0,0 +1,211 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file init.c
+ *
+ * FMU-specific early startup code. This file implements the
+ * board_app_initialize() function that is called early by nsh during startup.
+ *
+ * Code here is run before the rcS script is invoked; it should start required
+ * subsystems and perform board-specific initialisation.
+ */
+
+#include "board_config.h"
+
+#include <syslog.h>
+
+#include <nuttx/config.h>
+#include <nuttx/board.h>
+#include <nuttx/sdio.h>
+#include <nuttx/mmcsd.h>
+#include <arch/board/board.h>
+#include "arm_internal.h"
+
+#include <drivers/drv_hrt.h>
+#include <drivers/drv_board_led.h>
+#include <systemlib/px4_macros.h>
+#include <px4_arch/io_timer.h>
+#include <px4_platform_common/init.h>
+#include <px4_platform/gpio.h>
+#include <px4_platform/board_dma_alloc.h>
+#include <px4_platform/board_determine_hw_info.h>
+
+#include <mpu.h>
+
+# if defined(FLASH_BASED_PARAMS)
+#  include <parameters/flashparams/flashfs.h>
+#endif
+
+__BEGIN_DECLS
+extern void led_init(void);
+extern void led_on(int led);
+extern void led_off(int led);
+__END_DECLS
+
+/************************************************************************************
+ * Name: board_peripheral_reset
+ *
+ * Description:
+ *
+ ************************************************************************************/
+__EXPORT void board_peripheral_reset(int ms)
+{
+	UNUSED(ms);
+}
+
+/************************************************************************************
+ * Name: board_on_reset
+ *
+ * Description:
+ * Optionally provided function called on entry to board_system_reset
+ * It should perform any house keeping prior to the rest.
+ *
+ * status - 1 if resetting to boot loader
+ *          0 if just resetting
+ *
+ ************************************************************************************/
+__EXPORT void board_on_reset(int status)
+{
+	for (int i = 0; i < DIRECT_PWM_OUTPUT_CHANNELS; ++i) {
+		px4_arch_configgpio(PX4_MAKE_GPIO_INPUT(io_timer_channel_get_as_pwm_input(i)));
+	}
+
+	/*
+	 * On resets invoked from system (not boot) ensure we establish a low
+	 * output state on PWM pins to disarm the ESC and prevent the reset from potentially
+	 * spinning up the motors.
+	 */
+	if (status >= 0) {
+		up_mdelay(100);
+	}
+}
+
+/************************************************************************************
+ * Name: stm32_boardinitialize
+ *
+ * Description:
+ *   All STM32 architectures must provide the following entry point.  This entry point
+ *   is called early in the initialization -- after all memory has been configured
+ *   and mapped but before any devices have been initialized.
+ *
+ ************************************************************************************/
+__EXPORT void stm32_boardinitialize(void)
+{
+	/* Reset PWM first thing */
+	board_on_reset(-1);
+
+	/* configure LEDs */
+	board_autoled_initialize();
+
+	/* configure pins */
+	const uint32_t gpio[] = PX4_GPIO_INIT_LIST;
+	px4_gpio_init(gpio, arraySize(gpio));
+
+	/* configure SPI interfaces */
+	stm32_spiinitialize();
+
+	/* configure USB interfaces */
+	stm32_usbinitialize();
+
+}
+
+/****************************************************************************
+ * Name: board_app_initialize
+ *
+ * Description:
+ *   Perform application specific initialization.  This function is never
+ *   called directly from application code, but only indirectly via the
+ *   (non-standard) boardctl() interface using the command BOARDIOC_INIT.
+ *
+ * Input Parameters:
+ *   arg - The boardctl() argument is passed to the board_app_initialize()
+ *         implementation without modification.  The argument has no
+ *         meaning to NuttX;
+ *
+ * Returned Value:
+ *   Zero (OK) is returned on success; a negated errno value is returned on
+ *   any failure to indicate the nature of the failure.
+ *
+ ****************************************************************************/
+__EXPORT int board_app_initialize(uintptr_t arg)
+{
+	/* Need hrt running before using the ADC */
+	px4_platform_init();
+
+	/* configure the DMA allocator */
+	if (board_dma_alloc_init() < 0) {
+		syslog(LOG_ERR, "[boot] DMA alloc FAILED\n");
+	}
+
+	/* initial LED state */
+	drv_led_start();
+	led_off(LED_RED);
+	led_off(LED_BLUE);
+
+	if (board_hardfault_init(2, true) != 0) {
+		led_on(LED_BLUE);
+	}
+
+#ifdef CONFIG_MMCSD
+	int ret = stm32_sdio_initialize();
+
+	if (ret != OK) {
+		led_on(LED_BLUE);
+		return ret;
+	}
+
+#endif
+
+// TODO：internal flash store parameters
+#if defined(FLASH_BASED_PARAMS)
+	static sector_descriptor_t params_sector_map[] = {
+		{15, 128 * 1024, 0x081E0000},
+		{0, 0, 0},
+	};
+
+	/* Initialize the flashfs layer to use heap allocated memory */
+	int result = parameter_flashfs_init(params_sector_map, NULL, 0);
+
+	if (result != OK) {
+		syslog(LOG_ERR, "[boot] FAILED to init params in FLASH %d\n", result);
+		led_on(LED_RED);
+	}
+
+#endif
+
+	/* Configure the HW based on the manifest */
+	px4_platform_configure();
+
+	return OK;
+}

boards/x-mav/ap-h743r1/src/led.c

@@ -0,0 +1,113 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file led.c
+ *
+ * LED backend.
+ */
+
+#include <px4_platform_common/px4_config.h>
+
+#include <stdbool.h>
+
+#include "chip.h"
+#include "stm32_gpio.h"
+#include "board_config.h"
+
+#include <nuttx/board.h>
+#include <arch/board/board.h>
+
+/*
+ * Ideally we'd be able to get these from arm_internal.h,
+ * but since we want to be able to disable the NuttX use
+ * of leds for system indication at will and there is no
+ * separate switch, we need to build independent of the
+ * CONFIG_ARCH_LEDS configuration switch.
+ */
+__BEGIN_DECLS
+extern void led_init(void);
+extern void led_on(int led);
+extern void led_off(int led);
+extern void led_toggle(int led);
+__END_DECLS
+
+#  define xlat(p) (p)
+static uint32_t g_ledmap[] = {
+	GPIO_nLED_GREEN,   // Indexed by BOARD_LED_GREEN
+	GPIO_nLED_BLUE,    // Indexed by BOARD_LED_BLUE
+	GPIO_nLED_RED,     // Indexed by BOARD_LED_RED
+};
+
+__EXPORT void led_init(void)
+{
+	/* Configure LED GPIOs for output */
+	for (size_t l = 0; l < (sizeof(g_ledmap) / sizeof(g_ledmap[0])); l++) {
+		if (g_ledmap[l] != 0) {
+			stm32_configgpio(g_ledmap[l]);
+		}
+	}
+}
+
+static void phy_set_led(int led, bool state)
+{
+	/* Drive Low to switch on */
+	if (g_ledmap[led] != 0) {
+		stm32_gpiowrite(g_ledmap[led], !state);
+	}
+}
+
+static bool phy_get_led(int led)
+{
+	/* If Low it is on */
+	if (g_ledmap[led] != 0) {
+		return !stm32_gpioread(g_ledmap[led]);
+	}
+
+	return false;
+}
+
+__EXPORT void led_on(int led)
+{
+	phy_set_led(xlat(led), true);
+}
+
+__EXPORT void led_off(int led)
+{
+	phy_set_led(xlat(led), false);
+}
+
+__EXPORT void led_toggle(int led)
+{
+	phy_set_led(xlat(led), !phy_get_led(xlat(led)));
+}

boards/x-mav/ap-h743r1/src/mtd.cpp

@@ -0,0 +1,77 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2020 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+//TODO:Prepare for NxtDual
+
+#include <nuttx/spi/spi.h>
+#include <px4_platform_common/px4_manifest.h>
+//                                                              KiB BS    nB
+static const px4_mft_device_t spi5 = {             // FM25V02A on FMUM native: 32K X 8, emulated as (1024 Blocks of 32)
+	.bus_type = px4_mft_device_t::SPI,
+	.devid    = SPIDEV_FLASH(0)
+};
+
+static const px4_mtd_entry_t fmum_fram = {
+	.device = &spi5,
+	.npart = 1,
+	.partd = {
+		{
+			.type = MTD_PARAMETERS,
+			.path = "/fs/mtd_params",
+			.nblocks = 32
+		}
+	},
+};
+
+static const px4_mtd_manifest_t board_mtd_config = {
+	.nconfigs   = 1,
+	.entries = {
+		&fmum_fram
+	}
+};
+
+static const px4_mft_entry_s mtd_mft = {
+	.type = MTD,
+	.pmft = (void *) &board_mtd_config,
+};
+
+static const px4_mft_s mft = {
+	.nmft = 1,
+	.mfts = {
+		&mtd_mft
+	}
+};
+
+const px4_mft_s *board_get_manifest(void)
+{
+	return &mft;
+}

boards/x-mav/ap-h743r1/src/sdio.c

@@ -0,0 +1,177 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2014, 2016 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+#include <board_config.h>
+
+#include <stdbool.h>
+#include <stdio.h>
+#include <debug.h>
+#include <errno.h>
+
+#include <nuttx/sdio.h>
+#include <nuttx/mmcsd.h>
+
+#include "chip.h"
+#include "board_config.h"
+#include "stm32_gpio.h"
+#include "stm32_sdmmc.h"
+
+#ifdef CONFIG_MMCSD
+
+
+/****************************************************************************
+ * Pre-processor Definitions
+ ****************************************************************************/
+
+/* Card detections requires card support and a card detection GPIO */
+
+#define HAVE_NCD   1
+#if !defined(GPIO_SDMMC1_NCD)
+#  undef HAVE_NCD
+#endif
+
+/****************************************************************************
+ * Private Data
+ ****************************************************************************/
+
+static FAR struct sdio_dev_s *sdio_dev;
+#ifdef HAVE_NCD
+static bool g_sd_inserted = 0xff; /* Impossible value */
+#endif
+
+/****************************************************************************
+ * Private Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: stm32_ncd_interrupt
+ *
+ * Description:
+ *   Card detect interrupt handler.
+ *
+ ****************************************************************************/
+
+#ifdef HAVE_NCD
+static int stm32_ncd_interrupt(int irq, FAR void *context)
+{
+	bool present;
+
+	present = !stm32_gpioread(GPIO_SDMMC1_NCD);
+
+	if (sdio_dev && present != g_sd_inserted) {
+		sdio_mediachange(sdio_dev, present);
+		g_sd_inserted = present;
+	}
+
+	return OK;
+}
+#endif
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: stm32_sdio_initialize
+ *
+ * Description:
+ *   Initialize SDIO-based MMC/SD card support
+ *
+ ****************************************************************************/
+
+int stm32_sdio_initialize(void)
+{
+	int ret;
+
+#ifdef HAVE_NCD
+	/* Card detect */
+
+	bool cd_status;
+
+	/* Configure the card detect GPIO */
+
+	stm32_configgpio(GPIO_SDMMC1_NCD);
+
+	/* Register an interrupt handler for the card detect pin */
+
+	stm32_gpiosetevent(GPIO_SDMMC1_NCD, true, true, true, stm32_ncd_interrupt);
+#endif
+
+	/* Mount the SDIO-based MMC/SD block driver */
+	/* First, get an instance of the SDIO interface */
+
+	finfo("Initializing SDIO slot %d\n", SDIO_SLOTNO);
+
+	sdio_dev = sdio_initialize(SDIO_SLOTNO);
+
+	if (!sdio_dev) {
+		syslog(LOG_ERR, "[boot] Failed to initialize SDIO slot %d\n", SDIO_SLOTNO);
+		return -ENODEV;
+	}
+
+	/* Now bind the SDIO interface to the MMC/SD driver */
+
+	finfo("Bind SDIO to the MMC/SD driver, minor=%d\n", SDIO_MINOR);
+
+	ret = mmcsd_slotinitialize(SDIO_MINOR, sdio_dev);
+
+	if (ret != OK) {
+		syslog(LOG_ERR, "[boot] Failed to bind SDIO to the MMC/SD driver: %d\n", ret);
+		return ret;
+	}
+
+	finfo("Successfully bound SDIO to the MMC/SD driver\n");
+
+#ifdef HAVE_NCD
+	/* Use SD card detect pin to check if a card is g_sd_inserted */
+
+	cd_status = !stm32_gpioread(GPIO_SDMMC1_NCD);
+	finfo("Card detect : %d\n", cd_status);
+
+	sdio_mediachange(sdio_dev, cd_status);
+#else
+	/* Assume that the SD card is inserted.  What choice do we have? */
+
+	sdio_mediachange(sdio_dev, true);
+#endif
+
+	return OK;
+}
+
+#endif /* CONFIG_MMCSD */

boards/x-mav/ap-h743r1/src/spi.cpp

@@ -0,0 +1,52 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+#include <px4_arch/spi_hw_description.h>
+#include <drivers/drv_sensor.h>
+#include <nuttx/spi/spi.h>
+
+constexpr px4_spi_bus_t px4_spi_buses[SPI_BUS_MAX_BUS_ITEMS] = {
+	initSPIBus(SPI::Bus::SPI1, {
+		initSPIDevice(DRV_IMU_DEVTYPE_ICM42688P, SPI::CS{GPIO::PortA, GPIO::Pin2}, SPI::DRDY{GPIO::PortA, GPIO::Pin4}),
+		initSPIDevice(DRV_IMU_DEVTYPE_BMI270, SPI::CS{GPIO::PortA, GPIO::Pin2}, SPI::DRDY{GPIO::PortA, GPIO::Pin4})
+	}),
+	initSPIBus(SPI::Bus::SPI3, {
+		initSPIDevice(SPIDEV_FLASH(0), SPI::CS{GPIO::PortD, GPIO::Pin4})
+	}),
+	initSPIBus(SPI::Bus::SPI4, {
+		initSPIDevice(DRV_IMU_DEVTYPE_ICM42688P, SPI::CS{GPIO::PortC, GPIO::Pin13}, SPI::DRDY{GPIO::PortE, GPIO::Pin4}),
+		initSPIDevice(DRV_IMU_DEVTYPE_BMI270, SPI::CS{GPIO::PortC, GPIO::Pin13}, SPI::DRDY{GPIO::PortE, GPIO::Pin4})
+	}),
+};
+
+static constexpr bool unused = validateSPIConfig(px4_spi_buses);

boards/x-mav/ap-h743r1/src/timer_config.cpp

@@ -0,0 +1,53 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+#include <px4_arch/io_timer_hw_description.h>
+
+constexpr io_timers_t io_timers[MAX_IO_TIMERS] = {
+	initIOTimer(Timer::Timer1, DMA{DMA::Index1}),
+	initIOTimer(Timer::Timer2, DMA{DMA::Index1}),
+	initIOTimer(Timer::Timer3, DMA{DMA::Index1}),
+};
+
+constexpr timer_io_channels_t timer_io_channels[MAX_TIMER_IO_CHANNELS] = {
+	initIOTimerChannel(io_timers, {Timer::Timer1, Timer::Channel1}, {GPIO::PortE, GPIO::Pin9}),
+	initIOTimerChannel(io_timers, {Timer::Timer1, Timer::Channel2}, {GPIO::PortE, GPIO::Pin11}),
+	initIOTimerChannel(io_timers, {Timer::Timer1, Timer::Channel3}, {GPIO::PortE, GPIO::Pin13}),
+	initIOTimerChannel(io_timers, {Timer::Timer1, Timer::Channel4}, {GPIO::PortE, GPIO::Pin14}),
+	initIOTimerChannel(io_timers, {Timer::Timer3, Timer::Channel4}, {GPIO::PortB, GPIO::Pin1}),
+	initIOTimerChannel(io_timers, {Timer::Timer3, Timer::Channel3}, {GPIO::PortB, GPIO::Pin0}),
+	initIOTimerChannel(io_timers, {Timer::Timer2, Timer::Channel1}, {GPIO::PortA, GPIO::Pin0})
+};
+
+constexpr io_timers_channel_mapping_t io_timers_channel_mapping =
+	initIOTimerChannelMapping(io_timers, timer_io_channels);

boards/x-mav/ap-h743r1/src/usb.c

@@ -0,0 +1,78 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2021 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file usb.c
+ *
+ * Board-specific USB functions.
+ */
+
+#include "board_config.h"
+#include <nuttx/usb/usbdev.h>
+#include <nuttx/usb/usbdev_trace.h>
+#include <stm32_otg.h>
+#include <debug.h>
+
+/************************************************************************************
+ * Name: stm32_usbinitialize
+ *
+ * Description:
+ *   Called to setup USB-related GPIO pins for the board.
+ *
+ ************************************************************************************/
+
+__EXPORT void stm32_usbinitialize(void)
+{
+	/* The OTG FS has an internal soft pull-up */
+
+	/* Configure the OTG FS VBUS sensing GPIO, Power On, and Overcurrent GPIOs */
+
+#ifdef CONFIG_STM32H7_OTGFS
+	stm32_configgpio(GPIO_OTGFS_VBUS);
+#endif
+}
+
+/************************************************************************************
+ * Name:  stm32_usbsuspend
+ *
+ * Description:
+ *   Board logic must provide the stm32_usbsuspend logic if the USBDEV driver is
+ *   used.  This function is called whenever the USB enters or leaves suspend mode.
+ *   This is an opportunity for the board logic to shutdown clocks, power, etc.
+ *   while the USB is suspended.
+ *
+ ************************************************************************************/
+__EXPORT void stm32_usbsuspend(FAR struct usbdev_s *dev, bool resume)
+{
+	uinfo("resume: %d\n", resume);
+}

docs/en/SUMMARY.md

@@ -194,6 +194,7 @@
       - [SVehicle E2](flight_controller/svehicle_e2.md)
       - [ThePeach FCC-K1](flight_controller/thepeach_k1.md)
       - [ThePeach FCC-R1](flight_controller/thepeach_r1.md)
+      - [AP-H743-R1](flight_controller/x-mav_ap-h743r1.md)
     - [Experimental Autopilots](flight_controller/autopilot_experimental.md)
       - [BeagleBone Blue](flight_controller/beaglebone_blue.md)
       - [Raspberry Pi 2/3 Navio2](flight_controller/raspberry_pi_navio2.md)

docs/en/flight_controller/autopilot_manufacturer_supported.md

@@ -39,3 +39,4 @@ The boards in this category are:
 - [Svehicle E2](../flight_controller/svehicle_e2.md)
 - [ThePeach FCC-K1](../flight_controller/thepeach_k1.md)
 - [ThePeach FCC-R1](../flight_controller/thepeach_r1.md)
+- [X-MAV AP-H743-R1](../flight_controller/x-mav_ap-h743r1.md)

docs/en/flight_controller/x-mav_ap-h743r1.md

@@ -0,0 +1,145 @@
+# AP-H743-R1
+
+<Badge type="tip" text="main (planned for: PX4 v1.17)" />
+
+:::warning
+PX4 does not manufacture this (or any) autopilot.
+:::
+
+The AP-H743-R1 is an advanced autopilot manufactured by X-MAV<sup>&reg;</sup>.
+
+The autopilot is recommended for commercial system integration, but is also suitable for academic research and any other applications.
+It brings you ultimate performance, stability, and reliability in every aspect.
+
+![AP-H743-R1](../../assets/flight_controller/x-mav_ap-h743r1/ap-h743r1-main.png)
+
+::: info
+These flight controllers are [manufacturer supported](../flight_controller/autopilot_manufacturer_supported.md).
+:::
+
+### Processors & Sensors
+
+- FMU Processor: STM32H743VIT6
+  - 32 Bit Arm® Cortex®-M7, 480MHz, 2MB flash memory, 1MB RAM
+- IO Processor: STM32F103
+  - 32 Bit Arm® Cortex®-M3, 72MHz, 20KB SRAM
+- On-board sensors
+  - Accel/Gyro: ICM-42688-P\*2(Version1), BMI270\*2(Version2)
+  - Mag: IST8310
+  - Barometer: DPS310(Version1),SPL06(Version2)
+
+### Interfaces
+
+- 15x PWM Servo Outputs
+- 1x Dedicated S.Bus Input
+- 3x TELEM Ports
+- 1x SERIAL4 Port
+- 2x GPS Ports
+- 1x USB Port (TYPE-C)
+- 3x I2C Bus Ports
+- 2x CAN Ports
+- 2x Power Input Ports
+  - ADC Power Input
+  - DroneCAN/UAVCAN Power Input
+- 2x Dedicated Debug Port
+  - FMU Debug
+  - IO Debug
+
+## Purchase Channels
+
+Order from [X-MAV](https://www.x-mav.cn/).
+
+## Radio Control
+A Radio Control (RC) system is required if you want to manually control your vehicle (PX4 does not require a radio system for autonomous flight modes).
+
+You will need to select a compatible transmitter/receiver and then bind them so that they communicate (read the instructions that come with your specific transmitter/receiver).
+
+SBUS receivers connect to the SBUS-IN input port.
+CRSF receiver must be wired to a spare port (UART) on the Flight Controller. Then you can bind the transmitter and receiver together.
+
+## Serial Port Mapping
+
+| UART   | Device     | Port          |
+| ------ | ---------- | ------------- |
+| USART1 | /dev/ttyS0 | GPS           |
+| USART2 | /dev/ttyS1 | GPS2          |
+| USART3 | /dev/ttyS2 | TELEM1        |
+| UART4  | /dev/ttyS3 | TELEM2        |
+| UART7  | /dev/ttyS4 | TELEM3        |
+| UART8  | /dev/ttyS5 | SERIAL4       |
+
+## PWM Output
+
+The AP-H743-R1 flight controller supports up to 15 PWM outputs.
+The first 8 outputs (labelled M1 to M8) are controlled by a dedicated STM32F103 IOMCU controller.
+The remaining 7 outputs (labelled A1 to A7) are the "auxiliary" outputs.
+These are directly attached to the STM32H743 FMU controller .
+
+The 15 PWM outputs are:
+
+M1 - M8 are connected to the IOMCU.
+A1 - A7 are connected to the FMU.
+
+M1 - M8 support DShot and are in 3 groups:
+
+- M1, M2 in group 1
+- M3, M4 in group 2
+- M5, M6, M7, M8 in group 3
+
+The 7 FMU PWM outputs are in 3 groups:
+
+- A1 - A4 are in one group.
+- A5, A6 are in a 2nd group.
+- A7 is in a 3nd group.
+
+Channels within the same group need to use the same output rate.
+If any channel in a group uses DShot then all channels in the group need to use DShot.
+
+### Electrical data
+
+- Voltage Ratings:
+  - Max input voltage: 5.4V
+  - USB Power Input: 4.75\~5.25V
+  - Servo Rail Input: 0\~9.9V
+
+## Battery Monitoring
+
+The board has connectors for 2 power monitors.
+
+- POWER1 -- ADC
+- POWER2 -- DroneCAN
+
+The board is configure by default for a analog power monitor, and also has DroneCAN power monitor configured which is enabled.
+
+## Building Firmware
+
+To [build PX4](../dev_setup/building_px4.md) for this target, execute:
+
+```sh
+make x-mav_ap-h743r1_default
+```
+
+## Pinouts and Size
+
+![AP-H743-R1 pinouts](../../assets/flight_controller/x-mav_ap-h743r1/ap-h743r1-pinouts.png)
+
+![AP-H743-R1](../../assets/flight_controller/x-mav_ap-h743r1/ap-h743r1-size.png)
+
+## Supported Platforms / Airframes
+
+Any multirotor/airplane/rover or boat that can be controlled using normal RC servos or Futaba S-Bus servos.
+The complete set of supported configurations can be found in the [Airframe Reference](../airframes/airframe_reference.md).
+
+## Debug Port
+
+### SWD
+The [SWD interface](../debug/swd_debug.md) operate on the **FMU-DEBUG** port (`FMU-DEBUG`).
+
+The debug port (`FMU-DEBUG`) uses a [JST SM04B-GHS-TB](https://www.digikey.com/en/products/detail/jst-sales-america-inc/SM04B-GHS-TB/807788) connector and has the following pinout:
+
+| Pin     | Signal         | Volt  |
+| ------- | -------------- | ----- |
+| 1 (red) | 5V+            | +5V   |
+| 2 (blk) | FMU_SWDIO      | +3.3V |
+| 3 (blk) | FMU_SWCLK      | +3.3V |
+| 4 (blk) | GND            | GND   |