Removing obsolete code and files only.

FreeRTOS/Demo/CORTEX_M7_M4_AMP_STM32H745I_Discovery_IAR/CM4/main.c

@@ -264,7 +264,7 @@ uint32_t ulNextValue = 0;
 char cExpectedString[ 15 ];
 char cReceivedString[ 15 ];
 char cMessage;
-const TickType_t xShortBlockTime = pdMS_TO_TICKS( 5 );
+const TickType_t xShortBlockTime = pdMS_TO_TICKS( 150 );
 
 	/* This task is created more than once so the task's parameter is used to
 	pass in a task number, which is then used as an index into the message
@@ -332,28 +332,9 @@ const TickType_t xShortBlockTime = pdMS_TO_TICKS( 5 );
 
 void vGenerateM4ToM7Interrupt( void * xUpdatedMessageBuffer )
 {
-MessageBufferHandle_t xUpdatedBuffer = ( MessageBufferHandle_t ) xUpdatedMessageBuffer;
-const char cMessage[] = "\r\nvGenerateM4ToM7Interrupt\r\n";
-
 	/* Called by the implementation of sbRECEIVE_COMPLETED() in FreeRTOSConfig.h.
 	See the comments at the top of this file.  Write the handle of the data
 	message buffer to which data was written to the control message buffer. */
-#if 0
-	if( xUpdatedBuffer != xControlMessageBuffer )
-	{
-		while( xMessageBufferSend( xControlMessageBuffer, &xUpdatedBuffer, sizeof( xUpdatedBuffer ), mbaDONT_BLOCK ) != sizeof( xUpdatedBuffer ) )
-		{
-			/* Nothing to do here.  Note it is very bad to loop in an interrupt
-			service routine.  If a loop is really required then defer the
-			routine to a task. */
-		}
-
-		/* Generate interrupt in the M4 core. */
-		HAL_EXTI_D1_EventInputConfig( EXTI_LINE0, EXTI_MODE_IT, DISABLE );
-		HAL_EXTI_D2_EventInputConfig( EXTI_LINE0, EXTI_MODE_IT, ENABLE );
-		HAL_EXTI_GenerateSWInterrupt( EXTI_LINE0 );
-	}
-#endif
 
 	/* Generate interrupt in the M7 core. */
 	HAL_EXTI_D2_EventInputConfig( EXTI_LINE1, EXTI_MODE_IT, DISABLE );

FreeRTOS/Demo/CORTEX_M7_M4_AMP_STM32H745I_Discovery_IAR/CM7/main.c

@@ -244,7 +244,6 @@ static void prvM7CoreTasks( void *pvParameters )
 {
 BaseType_t x;
 uint32_t ulNextValue = 0;
-const TickType_t xDelay = pdMS_TO_TICKS( 25 );
 char cString[ 15 ];
 size_t xStringLength;
 
@@ -270,9 +269,6 @@ size_t xStringLength;
 									  	( void * ) cString,
 										xStringLength,
 										portMAX_DELAY ) != xStringLength );
-
-			/* Delay before repeating */
-//			vTaskDelay( xDelay );
 		}
 
 		ulNextValue++;

FreeRTOS/Demo/CORTEX_MPU_M23_Nuvoton_NuMaker_PFM_M2351_IAR_GCC/Projects/Keil/Secure/main_s.c

@@ -56,6 +56,46 @@ static void prvSetupHardware( void );
 static void prvBootNonSecure( uint32_t ulNonSecureStartAddress );
 /*-----------------------------------------------------------*/
 
+/* Secure main. */
+int main(void)
+{
+	/* Unlock protected registers. */
+	SYS_UnlockReg();
+
+	/* Initialize the hardware. */
+	prvSetupHardware();
+
+	/* Print banner. */
+	printf( "\n" );
+	printf( "+---------------------------------------------+\n" );
+	printf( "|            Secure is running ...            |\n" );
+	printf( "+---------------------------------------------+\n" );
+
+	/* Do not generate Systick interrupt on secure side. */
+	SysTick_Config( 1 );
+
+	/* Set GPIO Port A to non-secure for controlling LEDs from the non-secure
+	 * side . */
+	SCU_SET_IONSSET( SCU_IONSSET_PA_Msk );
+
+	/* Set UART0 to non-secure for debug output from non-secure side. */
+	SCU_SET_PNSSET( UART0_Attr );
+
+	/* Lock protected registers before booting non-secure code. */
+	SYS_LockReg();
+
+	/* Boot the non-secure code. */
+	printf( "Entering non-secure world ...\n" );
+	prvBootNonSecure( mainNONSECURE_APP_START_ADDRESS );
+
+	/* Non-secure software does not return, this code is not executed. */
+	for( ; ; )
+	{
+		/* Should not reach here. */
+	}
+}
+/*-----------------------------------------------------------*/
+
 static void prvSetupHardware( void )
 {
 	/* Init System Clock. */
@@ -126,42 +166,3 @@ static void prvBootNonSecure( uint32_t ulNonSecureStartAddress )
 }
 /*-----------------------------------------------------------*/
 
-/* Secure main. */
-int main(void)
-{
-	/* Unlock protected registers. */
-	SYS_UnlockReg();
-
-	/* Initialize the hardware. */
-	prvSetupHardware();
-
-	/* Print banner. */
-	printf( "\n" );
-	printf( "+---------------------------------------------+\n" );
-	printf( "|            Secure is running ...            |\n" );
-	printf( "+---------------------------------------------+\n" );
-
-	/* Do not generate Systick interrupt on secure side. */
-	SysTick_Config( 1 );
-
-	/* Set GPIO Port A to non-secure for controlling LEDs from the non-secure
-	 * side . */
-	SCU_SET_IONSSET( SCU_IONSSET_PA_Msk );
-
-	/* Set UART0 to non-secure for debug output from non-secure side. */
-	SCU_SET_PNSSET( UART0_Attr );
-
-	/* Lock protected registers before booting non-secure code. */
-	SYS_LockReg();
-
-	/* Boot the non-secure code. */
-	printf( "Entering non-secure world ...\n" );
-	prvBootNonSecure( mainNONSECURE_APP_START_ADDRESS );
-
-	/* Non-secure software does not return, this code is not executed. */
-	for( ; ; )
-	{
-		/* Should not reach here. */
-	}
-}
-/*-----------------------------------------------------------*/

FreeRTOS/Demo/CORTEX_MPU_M33F_NXP_LPC55S69_MCUXpresso/Projects/MCUXpresso/Secure/main_s.c

@@ -64,6 +64,31 @@ static void prvBootNonSecure( uint32_t ulNonSecureStartAddress );
 void SystemInitHook( void );
 /*-----------------------------------------------------------*/
 
+/* Secure main(). */
+int main(void)
+{
+	PRINTF( "Booting Secure World.\r\n" );
+
+	/* Attach main clock divide to FLEXCOMM0 (debug console). */
+	CLOCK_AttachClk( BOARD_DEBUG_UART_CLK_ATTACH );
+
+	/* Init board hardware. */
+	BOARD_InitPins();
+	BOARD_BootClockFROHF96M();
+	BOARD_InitDebugConsole();
+
+	/* Boot the non-secure code. */
+	PRINTF( "Booting Non-Secure World.\r\n" );
+	prvBootNonSecure( mainNONSECURE_APP_START_ADDRESS );
+
+	/* Non-secure software does not return, this code is not executed. */
+	for( ; ; )
+	{
+		/* Should not reach here. */
+	}
+}
+/*-----------------------------------------------------------*/
+
 static void prvBootNonSecure( uint32_t ulNonSecureStartAddress )
 {
 	NonSecureResetHandler_t pxNonSecureResetHandler;
@@ -100,27 +125,3 @@ void SystemInitHook( void )
 }
 /*-----------------------------------------------------------*/
 
-/* Secure main(). */
-int main(void)
-{
-	PRINTF( "Booting Secure World.\r\n" );
-
-	/* Attach main clock divide to FLEXCOMM0 (debug console). */
-	CLOCK_AttachClk( BOARD_DEBUG_UART_CLK_ATTACH );
-
-	/* Init board hardware. */
-	BOARD_InitPins();
-	BOARD_BootClockFROHF96M();
-	BOARD_InitDebugConsole();
-
-	/* Boot the non-secure code. */
-	PRINTF( "Booting Non-Secure World.\r\n" );
-	prvBootNonSecure( mainNONSECURE_APP_START_ADDRESS );
-
-	/* Non-secure software does not return, this code is not executed. */
-	for( ; ; )
-	{
-		/* Should not reach here. */
-	}
-}
-/*-----------------------------------------------------------*/