a05d9c18da
Add connectivity line stm32 to be able to compile SYSCFG, add definitions for
...
usb clock divs
2016-08-17 20:11:15 +02:00
795db7c103
Add support for onboard joystick
2016-08-15 21:52:00 +02:00
83fca7ded7
Add support for spi sdcard with card detection logic
2016-08-15 17:34:43 +02:00
8c396a2986
Add adc support (on-board potentiometer)
2016-08-14 17:16:49 +02:00
7bca86fa31
Add support for stm32butterfly ethernet interface
2016-08-14 16:33:48 +02:00
47fae83b16
Add minimal support for Kamami stm32butterfly2 development board
...
Supported is:
* LED1-4
* UART2 (terminal for nsh)
2016-08-14 16:32:11 +02:00
81df56086a
Fix bad pllmul values for stm32f1xx connectivity line.
...
stm32f1xx connectivity line supports only x4, x5, x6, x7, x8, x9 and x6.5 values
2016-08-11 10:49:57 +02:00
899a8aa2f0
SAMV7 TRNG: Missing endif.
2016-07-25 12:30:39 -06:00
4c1ba592d5
Prep for NuttX-7.17 release
2016-07-25 12:10:27 -06:00
524fc4a49e
Update ChangeLog
2016-07-24 13:54:48 -06:00
eb94cc5419
Update some comments
2016-07-24 12:48:37 -06:00
88cb41a0dc
configs/stm32f4discovery/canard: Change version to lastet. Need to match change to apps/libcanard/Kconfig
2016-07-24 07:52:33 -06:00
e895e19b9f
Minor changes from review of last PR
2016-07-24 07:45:46 -06:00
fe678cf351
Trivial change to a comment (only committed so that I can merge)
2016-07-24 07:39:46 -06:00
1d8a1bd901
Merged in gnagflow/nuttx (pull request #105 )
...
SAM3/4 USB and USBMSC fixes.
2016-07-24 07:37:35 -06:00
c0fa319f2b
SAM3/4 UDP: Fix handling of endpoint RX FIFO banks.
...
This fixes a race condition where the HW fills a FIFO bank while the SW is
busy, resulting in out of sequence USB packets.
2016-07-23 20:11:04 -07:00
cc191a977d
SAM3/4 UDP: Remove redundant EP state assignment.
2016-07-23 20:11:03 -07:00
4f83d58b24
USBMSC: Fix reversed logic on waiting for SCSI thread start.
...
The scsi thread was waiting for the wrong condition.
However, this was masked by the fact that the code creating the scsi thread
was also holding usbmsc_scsi_lock(priv) while initializing data, hence this
lock synchronized the scsi thread start with init completion.
2016-07-23 20:11:00 -07:00
2974d2b07e
USBMSC: Add locks when removing request from queue.
2016-07-23 20:10:41 -07:00
81f7758848
USBMSC: Fix usbtrace() string.
2016-07-23 20:10:20 -07:00
f3a6a40f62
SAM3/4 Serial: Fix warning when CONFIG_SUPPRESS_UART_CONFIG is set.
2016-07-23 16:23:49 -07:00
2d92bffdcc
Trivial change left in editor
2016-07-23 13:53:37 -06:00
a932578e76
GPIO driver: Add support for receiving signals from interrupt pins.
2016-07-23 13:53:06 -06:00
9b9b721406
Rename alarm_enable to rtc_alarm_enabled; mark inline
2016-07-23 12:01:57 -06:00
5a0f9fcb7d
Fix STM32 RTC Alarm interrupts. They were being enabled BEFORE the interrupt system was being initialized.
2016-07-23 10:36:06 -06:00
14de4b99f8
Simplify some computations
2016-07-23 08:13:25 -06:00
0984fcda44
Back out last RTC alarm changes. I am mistaken, the interrupts are enabled by stm32[l4]_exti_alarm().
2016-07-23 07:53:08 -06:00
65ac11692d
STM32L4 RTC is cloned from F4; needs same fix.
2016-07-23 07:33:44 -06:00
829c5610da
STM32 F4 RTC ALARM: Was not enabling interrupts.
2016-07-23 07:19:14 -06:00
e77872057d
Fix up a few remaining incorrect CONFIG_GPIO_IRQ
2016-07-22 15:01:00 -06:00
416aa99620
Correct name, not CONFIG_GPIO_IRQ but CONFIG_SAM34_GPIO_IRQ
2016-07-22 14:57:30 -06:00
b750dd5ff7
Correct name, not CONFIG_GPIO_IRQ but CONFIG_LPC43_GPIO_IRQ
2016-07-22 14:55:39 -06:00
c282e1d4ff
Correct name, not CONFIG_GPIO_IRQ but CONFIG_TIVA_GPIO_IRQS
2016-07-22 14:54:59 -06:00
e897ccb940
Rename x86 QEMU version of CONFIG_GPIO_IRQ to CONFIG_QEMU_GPIOIRQ
2016-07-22 14:54:00 -06:00
5a9519d636
Rename HCS12 version of CONFIG_GPIO_IRQ to CONFIG_HCS12_GPIOIRQ
2016-07-22 14:53:17 -06:00
c00ad93165
Rename HC version of CONFIG_GPIO_IRQ to CONFIG_HCS12_GPIOIRQ
2016-07-22 14:46:54 -06:00
e6137ff129
Rename SAMD/L version of CONFIG_GPIO_IRQ to CONFIG_SAMDL_GPIOIRQ
2016-07-22 14:38:33 -06:00
3aea9b8bf3
Rename KL version of CONFIG_GPIO_IRQ to CONFIG_KL_GPIOIRQ
2016-07-22 14:34:21 -06:00
5386403476
Rename Kinetis version of CONFIG_GPIO_IRQ to CONFIG_KINETIS_GPIOIRQ
2016-07-22 14:30:37 -06:00
264578135d
Rename LP11xx version of CONFIG_GPIO_IRQ to CONFIG_LPC11_GPIOIRQ
2016-07-22 14:23:31 -06:00
360efe03c1
Rename LP17xx version of CONFIG_GPIO_IRQ to CONFIG_LPC17_GPIOIRQ
2016-07-22 14:18:30 -06:00
fd42f898f6
libc: Add mkfifo() and pipe() to libc CSV file
2016-07-22 11:02:51 -06:00
9a8c3572db
serial.c: Fix a race condition noted by Stefan Kolb. Between the test if the TX buffer is full and entering a critical section, bytes may be removed from the TX buffer making the wait unnecessary. The unnecessary wait is an inefficiency, but not really a problem. But with USB CDC/ACM it can be a problem because the entire TX buffer may be emptied when we lose the race. If that happens that uart_putxmitchar() can hang waiting for data to be removed from an empty TX buffer.
2016-07-22 07:47:59 -06:00
369c942605
uint8_t is big enough for global. Range of values only 2-10
2016-07-21 15:18:27 -06:00
67900beaaa
LP43 Heap: REALLY eliminate the warning this time
2016-07-21 15:15:56 -06:00
d5acc120a4
Kinetis K60: Fix some bad conditional compilation
2016-07-21 14:22:00 -06:00
7370d3171a
Move include/nuttx/lib.h to include/nuttx/lib/lib.h
2016-07-21 14:05:44 -06:00
a2a47eb334
Move include/nuttx/float.h to include/nuttx/lib/float.h
2016-07-21 14:03:35 -06:00
779d3f98ed
Move include/nuttx/math32.h to include/nuttx/lib/math32.h
2016-07-21 14:00:15 -06:00
23a876ab9c
Move include/nuttx/math.h to include/nuttx/lib/math.h
2016-07-21 13:58:09 -06:00
Michał Łyszczek
Stefan Kolb
Gregory Nutt
Wolfgang Reissnegger
Wolfgang Reissnegger