SAM4S: Add NSH configuration. Calibrated delay loops. Port now seems fully functional

configs/sam4s-xplained/README.txt

@@ -436,6 +436,7 @@ SAM4S Xplained-specific Configuration Options
     CONFIG_SAM34_HSMCI       - High Speed Multimedia Card Interface
     CONFIG_SAM34_TWI0        - Two-Wire Interface 0
     CONFIG_SAM34_TWI1        - Two-Wire Interface 1
+    CONFIG_SAM34_SPI         - Serial Peripheral Interface
     CONFIG_SAM34_SSC         - Synchronous Serial Controller
     CONFIG_SAM34_TC0         - Timer Counter 0
     CONFIG_SAM34_TC1         - Timer Counter 1
@@ -555,3 +556,32 @@ Configurations
     2. This configuration is set up to use the NuttX OABI toolchain (see
        above). Of course this can be reconfigured if you prefer a different
        toolchain.
+
+  nsh:
+    This configuration directory will built the NuttShell.
+
+    NOTES:
+
+    1. This configuration provides test output on UART1 which is available
+       on J3 or J4 (see the section "Serial Consoles" above).  The
+       virtual COM port could be used, instead, by reconfiguring to use
+       UART0 instead of UART1:
+
+       System Type -> AT91SAM3/4 Peripheral Support
+         CONFIG_SAM_UART0=y
+         CONFIG_SAM_UART1=n
+
+       Device Drivers -> Serial Driver Support -> Serial Console
+         CONFIG_UART0_SERIAL_CONSOLE=y
+
+       Device Drivers -> Serial Driver Support -> USART0 Configuration
+         CONFIG_UART0_2STOP=0
+         CONFIG_UART0_BAUD=115200
+         CONFIG_UART0_BITS=8
+         CONFIG_UART0_PARITY=0
+         CONFIG_UART0_RXBUFSIZE=256
+         CONFIG_UART0_TXBUFSIZE=256
+
+    2. This configuration is set up to use the NuttX OABI toolchain (see
+       above). Of course this can be reconfigured if you prefer a different
+       toolchain.

configs/sam4s-xplained/include/board.h

@@ -166,7 +166,6 @@
 
 #define BOARD_FWS                  5
 
-
 /* LED definitions ******************************************************************/
 /* There are four LEDs on board the SAM4S Xplained board, two of these can be
  * controlled by software in the SAM4S:

configs/sam4s-xplained/nsh/Make.defs

@@ -0,0 +1,109 @@
+############################################################################
+# configs/sam4s-xplained/nsh/Make.defs
+#
+#   Copyright (C) 2013 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+include ${TOPDIR}/.config
+include ${TOPDIR}/tools/Config.mk
+include ${TOPDIR}/arch/arm/src/armv7-m/Toolchain.defs
+
+ifeq ($(WINTOOL),y)
+  # Windows-native toolchains
+  DIRLINK = $(TOPDIR)/tools/copydir.sh
+  DIRUNLINK = $(TOPDIR)/tools/unlink.sh
+  MKDEP = $(TOPDIR)/tools/mknulldeps.sh
+  ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
+  ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
+  ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/scripts/ld.script}"
+  MAXOPTIMIZATION = -O2
+else
+  # Linux/Cygwin-native toolchain 
+  MKDEP = $(TOPDIR)/tools/mkdeps.sh
+  ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
+  ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
+  ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/scripts/ld.script
+endif
+
+CC = $(CROSSDEV)gcc
+CXX = $(CROSSDEV)g++
+CPP = $(CROSSDEV)gcc -E
+LD = $(CROSSDEV)ld
+AR = $(CROSSDEV)ar rcs
+NM = $(CROSSDEV)nm
+OBJCOPY = $(CROSSDEV)objcopy
+OBJDUMP = $(CROSSDEV)objdump
+
+ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
+ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
+
+ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
+  ARCHOPTIMIZATION = -g
+else
+  ARCHOPTIMIZATION = $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
+endif
+
+ARCHCFLAGS = -fno-builtin
+ARCHCXXFLAGS = -fno-builtin -fno-exceptions
+ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
+ARCHWARNINGSXX = -Wall -Wshadow
+ARCHDEFINES =
+ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
+
+CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
+CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
+CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES)
+AFLAGS = $(CFLAGS) -D__ASSEMBLY__
+
+NXFLATLDFLAGS1 = -r -d -warn-common
+NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat-pcrel.ld -no-check-sections
+LDNXFLATFLAGS = -e main -s 2048
+
+OBJEXT = .o
+LIBEXT = .a
+EXEEXT =
+
+ifneq ($(CROSSDEV),arm-nuttx-elf-)
+  LDFLAGS += -nostartfiles -nodefaultlibs
+endif
+ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
+  LDFLAGS += -g
+endif
+
+
+HOSTCC = gcc
+HOSTINCLUDES = -I.
+HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
+HOSTLDFLAGS =
+

configs/sam4s-xplained/nsh/setenv.sh

@@ -0,0 +1,63 @@
+#!/bin/bash
+# configs/sam4s-xplained/nsh/setenv.sh
+#
+#   Copyright (C) 2013 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+
+
+if [ "$_" = "$0" ] ; then
+  echo "You must source this script, not run it!" 1>&2
+  exit 1
+fi
+
+WD=`pwd`
+if [ ! -x "setenv.sh" ]; then
+  echo "This script must be executed from the top-level NuttX build directory"
+  exit 1
+fi
+
+if [ -z "${PATH_ORIG}" ]; then
+  export PATH_ORIG="${PATH}"
+fi
+
+# This is the Cygwin path to the location where I installed the CodeSourcery
+# toolchain under windows.  You will also have to edit this if you install
+# the CodeSourcery toolchain in any other location
+#export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery G++ Lite/bin"
+
+# This is the Cygwin path to the location where I build the buildroot
+# toolchain.
+export TOOLCHAIN_BIN="${WD}/../misc/buildroot/build_arm_nofpu/staging_dir/bin"
+
+# Add the path to the toolchain to the PATH varialble
+export PATH="${TOOLCHAIN_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
+
+echo "PATH : ${PATH}"

configs/sam4s-xplained/ostest/defconfig

@@ -189,7 +189,7 @@ CONFIG_ARCH_HAVE_RAMVECTORS=y
 #
 # Board Settings
 #
-CONFIG_BOARD_LOOPSPERMSEC=4768
+CONFIG_BOARD_LOOPSPERMSEC=9186
 # CONFIG_ARCH_CALIBRATION is not set
 CONFIG_DRAM_START=0x20000000
 CONFIG_DRAM_SIZE=131072
@@ -319,7 +319,6 @@ CONFIG_DEV_LOWCONSOLE=y
 # CONFIG_16550_UART is not set
 CONFIG_ARCH_HAVE_UART1=y
 CONFIG_MCU_SERIAL=y
-# CONFIG_USART0_SERIAL_CONSOLE is not set
 CONFIG_UART1_SERIAL_CONSOLE=y
 # CONFIG_NO_SERIAL_CONSOLE is not set