add support to a new board : esp32s3-8048s043.

Documentation/platforms/xtensa/esp32s3/boards/esp32s3-8048S043/index.rst

@@ -0,0 +1,103 @@
+================
+ESP32S3-8048S043
+================
+
+.. tags:: chip:esp32, chip:esp32s3
+
+The `ESP32S3-8048S343 <https://www.openhasp.com/0.7.0/hardware/sunton/esp32-8048s0xx/>` is a dual-core MCU, integrated WI-FI and Bluetooth functions, the main frequency can reach 240MHz, 512KB SRAM, 384KB ROM, 8M PSRAM, Flash size is 16MB.
+
+.. list-table::
+   :align: center
+
+   * - .. figure:: esp32s3-8048S043.png
+          :align: center
+
+Features
+========
+
+  - ESP32-S3 WROOM-1 Module
+  - USB Type-C ports
+  - Power LED
+  - LCD Display
+  - 8MB Octal PSRAM
+  - 16MB SPI Flash
+  - TF card slot
+  - RST and BOOT buttons (BOOT accessible to user)
+
+Serial Console
+==============
+
+UART0 is, by default, the serial console.  It connects to the on-board
+CP2102 converter and is available on the USB connector USB CON8 (J1).
+
+It will show up as /dev/ttyUSB[n] where [n] will probably be 0.
+
+Buttons and I/Os
+================
+
+The board has two buttons: Boot and EN. The EN button functions only as 
+reset and is not available to software. The BOOT button (connected to IO0)
+determines boot mode during reset and can be used as software input after
+initialization. Most I/O pins are available on the back of the board through 
+two JST 1.28mm 4P connectors.
+
+Configurations
+==============
+
+All of the configurations presented below can be tested by running the following commands::
+
+    $ ./tools/configure.sh esp32s3-8048S043:<config_name>
+    $ make flash ESPTOOL_PORT=/dev/ttyUSB0 -j
+
+Where <config_name> is the name of board configuration you want to use, i.e.: nsh, buttons, tc...
+Then use a serial console terminal like ``picocom`` configured to 115200 8N1.
+
+buttons
+-------
+
+This configuration shows the use of the buttons subsystem. It can be used by executing
+the ``buttons`` application and pressing on any of the available board buttons::
+
+    nsh> buttons
+    buttons_main: Starting the button_daemon
+    buttons_main: button_daemon started
+    button_daemon: Running
+    button_daemon: Opening /dev/buttons
+    button_daemon: Supported BUTTONs 0x01
+    nsh> Sample = 1
+    Sample = 0
+
+nsh
+---
+
+Basic NuttShell configuration (console enabled in UART0, exposed via
+USB connection by means of CP2102 converter, at 115200 bps).
+
+i2c
+------
+
+This configuration can be used to scan and manipulate I2C devices.
+You can scan for all I2C devices using the following command::
+
+    nsh> i2c dev 0x00 0x7f
+
+touchscreen
+------------
+
+The LCD panel comes with the integrated capacitive touchscreen sensor 
+GT911 connected to the pins 20 (SCL), 19 (SDA) and address 0x5D::
+
+    nsh> tc
+    tc_main: nsamples: 0
+    tc_main: Opening /dev/input0
+    Sample     :
+       npoints : 1
+    Point 1    :
+            id : 0
+         flags : 31
+             x : 149
+             y : 140
+             h : 0
+             w : 0
+      pressure : 45
+     timestamp : 0

boards/Kconfig

@@ -477,6 +477,14 @@ config ARCH_BOARD_ESP32S3_DEVKIT
 		ESP32-S3-DevKitC-1 version may be based either on ESP32-S3-WROOM-1/1U or
 		ESP32-S3-WROOM-2/2U.
 
+config ARCH_BOARD_ESP32S3_8048S043
+	bool "ESP32-S3 8048S043"
+	depends on ARCH_CHIP_ESP32S3WROOM1N4 || ARCH_CHIP_ESP32S3MINI1N8 || ARCH_CHIP_ESP32S3WROOM1N8R2 || ARCH_CHIP_ESP32S3WROOM1N16R8 || ARCH_CHIP_ESP32S3WROOM2N16R8V || ARCH_CHIP_ESP32S3WROOM2N32R8V || ARCH_CHIP_ESP32S3CUSTOM || ARCH_CHIP_ESP32S3WROOM1N8R8
+	select ARCH_HAVE_BUTTONS
+	select ARCH_HAVE_IRQBUTTONS if ESP32S3_GPIO_IRQ
+	---help---
+		The ESP32-S3 8048S043 features the ESP32-S3 CPU with dual Xtensa LX7 cores.
+
 config ARCH_BOARD_ESP32S3_EYE
 	bool "Espressif ESP32-S3-EYE Board"
 	depends on ARCH_CHIP_ESP32S3WROOM1N4 || ARCH_CHIP_ESP32S3CUSTOM
@@ -3478,6 +3486,7 @@ config ARCH_BOARD
 	default "esp32s2-saola-1"           if ARCH_BOARD_ESP32S2_SAOLA_1
 	default "franzininho-wifi"          if ARCH_BOARD_FRANZININHO_WIFI
 	default "esp32s3-devkit"            if ARCH_BOARD_ESP32S3_DEVKIT
+	default "esp32s3-8048S043"          if ARCH_BOARD_ESP32S3_8048S043
 	default "esp32s3-eye"               if ARCH_BOARD_ESP32S3_EYE
 	default "esp32s3-meadow"            if ARCH_BOARD_ESP32S3_MEADOW
 	default "esp32s3-lcd-ev"            if ARCH_BOARD_ESP32S3_LCD_EV
@@ -4720,6 +4729,9 @@ endif
 if ARCH_BOARD_ESP32S3_DEVKIT
 source "boards/xtensa/esp32s3/esp32s3-devkit/Kconfig"
 endif
+if ARCH_BOARD_ESP32S3_8048S043
+source "boards/xtensa/esp32s3/esp32s3-8048S043/Kconfig"
+endif
 if ARCH_BOARD_ESP32S3_EYE
 source "boards/xtensa/esp32s3/esp32s3-eye/Kconfig"
 endif

boards/xtensa/esp32s3/esp32s3-8048S043/Kconfig

@@ -0,0 +1,55 @@
+#
+# For a description of the syntax of this configuration file,
+# see the file kconfig-language.txt in the NuttX tools repository.
+#
+
+if ARCH_BOARD_ESP32S3_8048S043
+
+config ESP32S3_BOARD_TOUCHSCREEN
+	bool "Enable Board Touchscreen"
+	default n
+	select ESP32S3_I2C0
+	select INPUT
+	select INPUT_TOUCHSCREEN
+	select INPUT_GT9XX
+	---help---
+		Enable board touchscreen support, IC is: GT911
+
+menu "Board Touchscreen Configuration"
+	depends on ESP32S3_BOARD_TOUCHSCREEN
+
+config ESP32S3_BOARD_TOUCHSCREEN_PATH
+	string "Touchscreen Path for VFS"
+	default "/dev/input0"
+
+config ESP32S3_BOARD_TOUCHSCREEN_WIDTH
+	int "Touchscreen Width"
+	default 800
+	depends on ESP32S3_8048S043
+
+config ESP32S3_BOARD_TOUCHSCREEN_HEIGHT
+	int "Touchscreen Height"
+	default 480
+	depends on ESP32S3_8048S043
+
+config ESP32S3_BOARD_TOUCHSCREEN_SAMPLE_CACHES
+	int "Touchscreen Sample Cache Number"
+	default 64
+
+config ESP32S3_BOARD_TOUCHSCREEN_SAMPLE_DELAYS
+	int "Touchscreen Sample Delay Ticks"
+	default 20
+
+config ESP32S3_BOARD_TOUCHSCREEN_X_MIRROR
+	bool "Touchscreen X Mirror"
+	default y
+	depends on ESP32S3_8048S043
+
+config ESP32S3_BOARD_TOUCHSCREEN_Y_MIRROR
+	bool "Touchscreen Y Mirror"
+	default n
+	depends on ESP32S3_8048S043
+
+endmenu # Touchscreen Configuration
+
+endif # ARCH_BOARD_ESP32S3_8048S043

boards/xtensa/esp32s3/esp32s3-8048S043/configs/gpio/defconfig

@@ -0,0 +1,50 @@
+#
+# This file is autogenerated: PLEASE DO NOT EDIT IT.
+#
+# You can use "make menuconfig" to make any modifications to the installed .config file.
+# You can then do "make savedefconfig" to generate a new defconfig file that includes your
+# modifications.
+#
+# CONFIG_NSH_ARGCAT is not set
+# CONFIG_NSH_CMDOPT_HEXDUMP is not set
+CONFIG_ARCH="xtensa"
+CONFIG_ARCH_BOARD="esp32s3-8048S043"
+CONFIG_ARCH_BOARD_COMMON=y
+CONFIG_ARCH_BOARD_ESP32S3_8048S043=y
+CONFIG_ARCH_CHIP="esp32s3"
+CONFIG_ARCH_CHIP_ESP32S3=y
+CONFIG_ARCH_CHIP_ESP32S3WROOM1N4=y
+CONFIG_ARCH_INTERRUPTSTACK=2048
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_ARCH_XTENSA=y
+CONFIG_BOARD_LOOPSPERMSEC=16717
+CONFIG_BUILTIN=y
+CONFIG_DEBUG_FULLOPT=y
+CONFIG_DEBUG_SYMBOLS=y
+CONFIG_DEV_GPIO=y
+CONFIG_ESP32S3_GPIO_IRQ=y
+CONFIG_ESP32S3_UART0=y
+CONFIG_EXAMPLES_GPIO=y
+CONFIG_FS_PROCFS=y
+CONFIG_HAVE_CXX=y
+CONFIG_HAVE_CXXINITIALIZE=y
+CONFIG_IDLETHREAD_STACKSIZE=3072
+CONFIG_INIT_ENTRYPOINT="nsh_main"
+CONFIG_INIT_STACKSIZE=3072
+CONFIG_INTELHEX_BINARY=y
+CONFIG_LINE_MAX=64
+CONFIG_NSH_ARCHINIT=y
+CONFIG_NSH_BUILTIN_APPS=y
+CONFIG_NSH_FILEIOSIZE=512
+CONFIG_NSH_READLINE=y
+CONFIG_PREALLOC_TIMERS=4
+CONFIG_RAM_SIZE=114688
+CONFIG_RAM_START=0x20000000
+CONFIG_RR_INTERVAL=200
+CONFIG_SCHED_WAITPID=y
+CONFIG_START_DAY=6
+CONFIG_START_MONTH=12
+CONFIG_START_YEAR=2011
+CONFIG_SYSLOG_BUFFER=y
+CONFIG_SYSTEM_NSH=y
+CONFIG_UART0_SERIAL_CONSOLE=y

boards/xtensa/esp32s3/esp32s3-8048S043/configs/i2c/defconfig

@@ -0,0 +1,57 @@
+#
+# This file is autogenerated: PLEASE DO NOT EDIT IT.
+#
+# You can use "make menuconfig" to make any modifications to the installed .config file.
+# You can then do "make savedefconfig" to generate a new defconfig file that includes your
+# modifications.
+#
+# CONFIG_NSH_ARGCAT is not set
+# CONFIG_NSH_CMDOPT_HEXDUMP is not set
+CONFIG_ARCH="xtensa"
+CONFIG_ARCH_BOARD="esp32s3-8048S043"
+CONFIG_ARCH_BOARD_COMMON=y
+CONFIG_ARCH_BOARD_ESP32S3_8048S043=y
+CONFIG_ARCH_CHIP="esp32s3"
+CONFIG_ARCH_CHIP_ESP32S3=y
+CONFIG_ARCH_CHIP_ESP32S3WROOM1N4=y
+CONFIG_ARCH_INTERRUPTSTACK=2048
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_ARCH_XTENSA=y
+CONFIG_BOARD_LOOPSPERMSEC=16717
+CONFIG_BUILTIN=y
+CONFIG_DEBUG_ASSERTIONS=y
+CONFIG_DEBUG_FEATURES=y
+CONFIG_DEBUG_I2C=y
+CONFIG_DEBUG_I2C_ERROR=y
+CONFIG_DEBUG_I2C_INFO=y
+CONFIG_DEBUG_I2C_WARN=y
+CONFIG_ESP32S3_I2C0=y
+CONFIG_ESP32S3_UART0=y
+CONFIG_FS_PROCFS=y
+CONFIG_HAVE_CXX=y
+CONFIG_HAVE_CXXINITIALIZE=y
+CONFIG_I2CTOOL_DEFFREQ=100000
+CONFIG_I2CTOOL_MAXBUS=1
+CONFIG_I2C_RESET=y
+CONFIG_I2C_TRACE=y
+CONFIG_IDLETHREAD_STACKSIZE=3072
+CONFIG_INIT_ENTRYPOINT="nsh_main"
+CONFIG_INIT_STACKSIZE=3072
+CONFIG_INTELHEX_BINARY=y
+CONFIG_LINE_MAX=64
+CONFIG_NSH_ARCHINIT=y
+CONFIG_NSH_BUILTIN_APPS=y
+CONFIG_NSH_FILEIOSIZE=512
+CONFIG_NSH_READLINE=y
+CONFIG_PREALLOC_TIMERS=4
+CONFIG_RAM_SIZE=114688
+CONFIG_RAM_START=0x20000000
+CONFIG_RR_INTERVAL=200
+CONFIG_SCHED_WAITPID=y
+CONFIG_START_DAY=28
+CONFIG_START_MONTH=6
+CONFIG_START_YEAR=2022
+CONFIG_SYSLOG_BUFFER=y
+CONFIG_SYSTEM_I2CTOOL=y
+CONFIG_SYSTEM_NSH=y
+CONFIG_UART0_SERIAL_CONSOLE=y

boards/xtensa/esp32s3/esp32s3-8048S043/configs/nsh/defconfig

@@ -0,0 +1,47 @@
+#
+# This file is autogenerated: PLEASE DO NOT EDIT IT.
+#
+# You can use "make menuconfig" to make any modifications to the installed .config file.
+# You can then do "make savedefconfig" to generate a new defconfig file that includes your
+# modifications.
+#
+# CONFIG_NSH_ARGCAT is not set
+# CONFIG_NSH_CMDOPT_HEXDUMP is not set
+CONFIG_ARCH="xtensa"
+CONFIG_ARCH_BOARD="esp32s3-8048S043"
+CONFIG_ARCH_BOARD_COMMON=y
+CONFIG_ARCH_BOARD_ESP32S3_8048S043=y
+CONFIG_ARCH_CHIP="esp32s3"
+CONFIG_ARCH_CHIP_ESP32S3=y
+CONFIG_ARCH_CHIP_ESP32S3WROOM1N4=y
+CONFIG_ARCH_INTERRUPTSTACK=2048
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_ARCH_XTENSA=y
+CONFIG_BOARD_LOOPSPERMSEC=16717
+CONFIG_BUILTIN=y
+CONFIG_DEBUG_FULLOPT=y
+CONFIG_DEBUG_SYMBOLS=y
+CONFIG_ESP32S3_UART0=y
+CONFIG_FS_PROCFS=y
+CONFIG_HAVE_CXX=y
+CONFIG_HAVE_CXXINITIALIZE=y
+CONFIG_IDLETHREAD_STACKSIZE=3072
+CONFIG_INIT_ENTRYPOINT="nsh_main"
+CONFIG_INIT_STACKSIZE=3072
+CONFIG_INTELHEX_BINARY=y
+CONFIG_LINE_MAX=64
+CONFIG_NSH_ARCHINIT=y
+CONFIG_NSH_BUILTIN_APPS=y
+CONFIG_NSH_FILEIOSIZE=512
+CONFIG_NSH_READLINE=y
+CONFIG_PREALLOC_TIMERS=4
+CONFIG_RAM_SIZE=114688
+CONFIG_RAM_START=0x20000000
+CONFIG_RR_INTERVAL=200
+CONFIG_SCHED_WAITPID=y
+CONFIG_START_DAY=6
+CONFIG_START_MONTH=12
+CONFIG_START_YEAR=2011
+CONFIG_SYSLOG_BUFFER=y
+CONFIG_SYSTEM_NSH=y
+CONFIG_UART0_SERIAL_CONSOLE=y

boards/xtensa/esp32s3/esp32s3-8048S043/configs/sdmmc/defconfig

@@ -0,0 +1,51 @@
+#
+# This file is autogenerated: PLEASE DO NOT EDIT IT.
+#
+# You can use "make menuconfig" to make any modifications to the installed .config file.
+# You can then do "make savedefconfig" to generate a new defconfig file that includes your
+# modifications.
+#
+# CONFIG_NSH_ARGCAT is not set
+# CONFIG_NSH_CMDOPT_HEXDUMP is not set
+CONFIG_ARCH="xtensa"
+CONFIG_ARCH_BOARD="esp32s3-8048S043"
+CONFIG_ARCH_BOARD_COMMON=y
+CONFIG_ARCH_BOARD_ESP32S3_8048S043=y
+CONFIG_ARCH_CHIP="esp32s3"
+CONFIG_ARCH_CHIP_ESP32S3=y
+CONFIG_ARCH_CHIP_ESP32S3WROOM1N4=y
+CONFIG_ARCH_INTERRUPTSTACK=2048
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_ARCH_XTENSA=y
+CONFIG_BOARD_LOOPSPERMSEC=16717
+CONFIG_BUILTIN=y
+CONFIG_DEBUG_FULLOPT=y
+CONFIG_DEBUG_SYMBOLS=y
+CONFIG_ESP32S3_SDMMC=y
+CONFIG_ESP32S3_UART0=y
+CONFIG_FS_FAT=y
+CONFIG_FS_PROCFS=y
+CONFIG_HAVE_CXX=y
+CONFIG_HAVE_CXXINITIALIZE=y
+CONFIG_IDLETHREAD_STACKSIZE=3072
+CONFIG_INIT_ENTRYPOINT="nsh_main"
+CONFIG_INIT_STACKSIZE=3072
+CONFIG_INTELHEX_BINARY=y
+CONFIG_LINE_MAX=64
+CONFIG_MMCSD_CHECK_READY_STATUS_WITHOUT_SLEEP=y
+CONFIG_MMCSD_MULTIBLOCK_LIMIT=128
+CONFIG_NSH_ARCHINIT=y
+CONFIG_NSH_BUILTIN_APPS=y
+CONFIG_NSH_FILEIOSIZE=512
+CONFIG_NSH_READLINE=y
+CONFIG_PREALLOC_TIMERS=4
+CONFIG_RAM_SIZE=114688
+CONFIG_RAM_START=0x20000000
+CONFIG_RR_INTERVAL=200
+CONFIG_SCHED_WAITPID=y
+CONFIG_START_DAY=6
+CONFIG_START_MONTH=12
+CONFIG_START_YEAR=2011
+CONFIG_SYSLOG_BUFFER=y
+CONFIG_SYSTEM_NSH=y
+CONFIG_UART0_SERIAL_CONSOLE=y

boards/xtensa/esp32s3/esp32s3-8048S043/configs/spi/defconfig

@@ -0,0 +1,49 @@
+#
+# This file is autogenerated: PLEASE DO NOT EDIT IT.
+#
+# You can use "make menuconfig" to make any modifications to the installed .config file.
+# You can then do "make savedefconfig" to generate a new defconfig file that includes your
+# modifications.
+#
+# CONFIG_NSH_ARGCAT is not set
+# CONFIG_NSH_CMDOPT_HEXDUMP is not set
+CONFIG_ARCH="xtensa"
+CONFIG_ARCH_BOARD="esp32s3-8048S043"
+CONFIG_ARCH_BOARD_COMMON=y
+CONFIG_ARCH_BOARD_ESP32S3_8048S043=y
+CONFIG_ARCH_CHIP="esp32s3"
+CONFIG_ARCH_CHIP_ESP32S3=y
+CONFIG_ARCH_CHIP_ESP32S3WROOM1N4=y
+CONFIG_ARCH_INTERRUPTSTACK=2048
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_ARCH_XTENSA=y
+CONFIG_BOARD_LOOPSPERMSEC=16717
+CONFIG_BUILTIN=y
+CONFIG_ESP32S3_SPI2=y
+CONFIG_ESP32S3_SPI3=y
+CONFIG_ESP32S3_UART0=y
+CONFIG_FS_PROCFS=y
+CONFIG_HAVE_CXX=y
+CONFIG_HAVE_CXXINITIALIZE=y
+CONFIG_IDLETHREAD_STACKSIZE=3072
+CONFIG_INIT_ENTRYPOINT="nsh_main"
+CONFIG_INIT_STACKSIZE=3072
+CONFIG_INTELHEX_BINARY=y
+CONFIG_LINE_MAX=64
+CONFIG_NSH_ARCHINIT=y
+CONFIG_NSH_BUILTIN_APPS=y
+CONFIG_NSH_FILEIOSIZE=512
+CONFIG_NSH_READLINE=y
+CONFIG_PREALLOC_TIMERS=4
+CONFIG_RAM_SIZE=114688
+CONFIG_RAM_START=0x20000000
+CONFIG_RR_INTERVAL=200
+CONFIG_SCHED_WAITPID=y
+CONFIG_SPITOOL_MINBUS=2
+CONFIG_START_DAY=6
+CONFIG_START_MONTH=12
+CONFIG_START_YEAR=2011
+CONFIG_SYSLOG_BUFFER=y
+CONFIG_SYSTEM_NSH=y
+CONFIG_SYSTEM_SPITOOL=y
+CONFIG_UART0_SERIAL_CONSOLE=y

boards/xtensa/esp32s3/esp32s3-8048S043/configs/touchscreen/defconfig

@@ -0,0 +1,58 @@
+#
+# This file is autogenerated: PLEASE DO NOT EDIT IT.
+#
+# You can use "make menuconfig" to make any modifications to the installed .config file.
+# You can then do "make savedefconfig" to generate a new defconfig file that includes your
+# modifications.
+#
+# CONFIG_NSH_ARGCAT is not set
+# CONFIG_NSH_CMDOPT_HEXDUMP is not set
+CONFIG_ARCH="xtensa"
+CONFIG_ARCH_BOARD="esp32s3-8048S043"
+CONFIG_ARCH_BOARD_COMMON=y
+CONFIG_ARCH_BOARD_ESP32S3_8048S043=y
+CONFIG_ARCH_CHIP="esp32s3"
+CONFIG_ARCH_CHIP_ESP32S3=y
+CONFIG_ARCH_CHIP_ESP32S3WROOM1N4=y
+CONFIG_ARCH_INTERRUPTSTACK=2048
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_ARCH_XTENSA=y
+CONFIG_BOARD_LOOPSPERMSEC=16717
+CONFIG_BUILTIN=y
+CONFIG_DEBUG_ASSERTIONS=y
+CONFIG_DEBUG_FEATURES=y
+CONFIG_ESP32S3_BOARD_TOUCHSCREEN=y
+CONFIG_ESP32S3_BOARD_TOUCHSCREEN_SAMPLE_CACHES=16
+CONFIG_ESP32S3_BOARD_TOUCHSCREEN_SAMPLE_DELAYS=5
+CONFIG_ESP32S3_I2C0_SCLPIN=20
+CONFIG_ESP32S3_I2C0_SDAPIN=19
+CONFIG_ESP32S3_UART0=y
+CONFIG_EXAMPLES_TOUCHSCREEN=y
+CONFIG_FS_PROCFS=y
+CONFIG_HAVE_CXX=y
+CONFIG_HAVE_CXXINITIALIZE=y
+CONFIG_I2CTOOL_DEFFREQ=100000
+CONFIG_I2CTOOL_MAXBUS=1
+CONFIG_I2C_RESET=y
+CONFIG_IDLETHREAD_STACKSIZE=3072
+CONFIG_INIT_ENTRYPOINT="nsh_main"
+CONFIG_INIT_STACKSIZE=3072
+CONFIG_INTELHEX_BINARY=y
+CONFIG_LINE_MAX=64
+CONFIG_NSH_ARCHINIT=y
+CONFIG_NSH_BUILTIN_APPS=y
+CONFIG_NSH_FILEIOSIZE=512
+CONFIG_NSH_READLINE=y
+CONFIG_PREALLOC_TIMERS=4
+CONFIG_RAM_SIZE=114688
+CONFIG_RAM_START=0x20000000
+CONFIG_RR_INTERVAL=200
+CONFIG_SCHED_LPWORK=y
+CONFIG_SCHED_WAITPID=y
+CONFIG_START_DAY=28
+CONFIG_START_MONTH=6
+CONFIG_START_YEAR=2022
+CONFIG_SYSLOG_BUFFER=y
+CONFIG_SYSTEM_I2CTOOL=y
+CONFIG_SYSTEM_NSH=y
+CONFIG_UART0_SERIAL_CONSOLE=y

boards/xtensa/esp32s3/esp32s3-8048S043/include/board.h

@@ -0,0 +1,54 @@
+/****************************************************************************
+ * boards/xtensa/esp32s3/esp32s3-8048S043/include/board.h
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed to the Apache Software Foundation (ASF) under one or more
+ * contributor license agreements.  See the NOTICE file distributed with
+ * this work for additional information regarding copyright ownership.  The
+ * ASF licenses this file to you under the Apache License, Version 2.0 (the
+ * "License"); you may not use this file except in compliance with the
+ * License.  You may obtain a copy of the License at
+ *
+ *   http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
+ * License for the specific language governing permissions and limitations
+ * under the License.
+ *
+ ****************************************************************************/
+
+#ifndef __BOARDS_XTENSA_ESP32S3_ESP32S3_8048S043_INCLUDE_BOARD_H
+#define __BOARDS_XTENSA_ESP32S3_ESP32S3_8048S043_INCLUDE_BOARD_H
+
+/****************************************************************************
+ * Pre-processor Definitions
+ ****************************************************************************/
+
+/* Clocking *****************************************************************/
+
+/* The ESP32-S3 8048S043 board is fitted with a 40MHz crystal */
+
+#define BOARD_XTAL_FREQUENCY    40000000
+
+#ifdef CONFIG_ESP32S3_DEFAULT_CPU_FREQ_MHZ
+#  define BOARD_CLOCK_FREQUENCY (CONFIG_ESP32S3_DEFAULT_CPU_FREQ_MHZ * 1000000)
+#else
+#  define BOARD_CLOCK_FREQUENCY 80000000
+#endif
+
+/* LED definitions **********************************************************/
+
+/* Define how many LEDs this board has (needed by userleds) */
+
+#define BOARD_NLEDS             0
+
+/* GPIO pins used by the GPIO Subsystem */
+
+#define BOARD_NGPIOOUT    1 /* Amount of GPIO Output pins */
+#define BOARD_NGPIOIN     1 /* Amount of GPIO Input without Interruption */
+#define BOARD_NGPIOINT    1 /* Amount of GPIO Input w/ Interruption pins */
+
+#endif /* __BOARDS_XTENSA_ESP32S3_ESP32S3_8048S043_INCLUDE_BOARD_H */

boards/xtensa/esp32s3/esp32s3-8048S043/include/board_memorymap.h

@@ -0,0 +1,118 @@
+/****************************************************************************
+ * boards/xtensa/esp32s3/esp32s3-8048S043/include/board_memorymap.h
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed to the Apache Software Foundation (ASF) under one or more
+ * contributor license agreements.  See the NOTICE file distributed with
+ * this work for additional information regarding copyright ownership.  The
+ * ASF licenses this file to you under the Apache License, Version 2.0 (the
+ * "License"); you may not use this file except in compliance with the
+ * License.  You may obtain a copy of the License at
+ *
+ *   http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
+ * License for the specific language governing permissions and limitations
+ * under the License.
+ *
+ ****************************************************************************/
+
+#ifndef __BOARDS_XTENSA_ESP32S3_ESP32S3_8048S043_INCLUDE_BOARD_MEMORYMAP_H
+#define __BOARDS_XTENSA_ESP32S3_ESP32S3_8048S043_INCLUDE_BOARD_MEMORYMAP_H
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <stdint.h>
+
+/****************************************************************************
+ * Pre-processor Definitions
+ ****************************************************************************/
+
+/* Kernel ROM */
+
+#define KIROM_START     (uintptr_t)__kirom_start
+#define KIROM_SIZE      (uintptr_t)__kirom_size
+#define KDROM_START     (uintptr_t)__kdrom_start
+#define KDROM_SIZE      (uintptr_t)__kdrom_size
+
+/* Kernel RAM */
+
+#define KIRAM_START     (uintptr_t)__kiram_start
+#define KIRAM_SIZE      (uintptr_t)__kiram_size
+#define KIRAM_END       (uintptr_t)__kiram_end
+#define KDRAM_START     (uintptr_t)__kdram_start
+#define KDRAM_SIZE      (uintptr_t)__kdram_size
+#define KDRAM_END       (uintptr_t)__kdram_end
+
+/* Exception vectors */
+
+#define VECTORS_START   (uintptr_t)__vectors_start
+#define VECTORS_END     (uintptr_t)__vectors_end
+
+/* User ROM */
+
+#define UIROM_START     (uintptr_t)__uirom_start
+#define UIROM_SIZE      (uintptr_t)__uirom_size
+#define UIROM_END       (uintptr_t)__uirom_end
+#define UDROM_START     (uintptr_t)__udrom_start
+#define UDROM_SIZE      (uintptr_t)__udrom_size
+#define UDROM_END       (uintptr_t)__udrom_end
+
+/* User RAM */
+
+#define UIRAM_START     (uintptr_t)__uiram_start
+#define UIRAM_SIZE      (uintptr_t)__uiram_size
+#define UIRAM_END       (uintptr_t)__uiram_end
+#define UDRAM_START     (uintptr_t)__udram_start
+#define UDRAM_SIZE      (uintptr_t)__udram_size
+#define UDRAM_END       (uintptr_t)__udram_end
+
+/****************************************************************************
+ * Public Data
+ ****************************************************************************/
+
+/* Kernel ROM (RX)  */
+
+extern uint8_t          __kirom_start[];
+extern uint8_t          __kirom_size[];
+extern uint8_t          __kdrom_start[];
+extern uint8_t          __kdrom_size[];
+
+/* Kernel RAM (RW) */
+
+extern uint8_t          __kiram_start[];
+extern uint8_t          __kiram_size[];
+extern uint8_t          __kiram_end[];
+extern uint8_t          __kdram_start[];
+extern uint8_t          __kdram_size[];
+extern uint8_t          __kdram_end[];
+
+/* Exception vectors */
+
+extern uint8_t          __vectors_start[];
+extern uint8_t          __vectors_end[];
+
+/* User ROM (RX) */
+
+extern uint8_t          __uirom_start[];
+extern uint8_t          __uirom_size[];
+extern uint8_t          __uirom_end[];
+extern uint8_t          __udrom_start[];
+extern uint8_t          __udrom_size[];
+extern uint8_t          __udrom_end[];
+
+/* User RAM (RW) */
+
+extern uint8_t          __uiram_start[];
+extern uint8_t          __uiram_size[];
+extern uint8_t          __uiram_end[];
+extern uint8_t          __udram_start[];
+extern uint8_t          __udram_size[];
+extern uint8_t          __udram_end[];
+
+#endif /* __BOARDS_XTENSA_ESP32S3_ESP32S3_8048S043_INCLUDE_BOARD_MEMORYMAP_H */

boards/xtensa/esp32s3/esp32s3-8048S043/scripts/Make.defs

@@ -0,0 +1,57 @@
+############################################################################
+# boards/xtensa/esp32s3/esp32s3-8048S043/scripts/Make.defs
+#
+# SPDX-License-Identifier: Apache-2.0
+#
+# Licensed to the Apache Software Foundation (ASF) under one or more
+# contributor license agreements.  See the NOTICE file distributed with
+# this work for additional information regarding copyright ownership.  The
+# ASF licenses this file to you under the Apache License, Version 2.0 (the
+# "License"); you may not use this file except in compliance with the
+# License.  You may obtain a copy of the License at
+#
+#   http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+# WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
+# License for the specific language governing permissions and limitations
+# under the License.
+#
+############################################################################
+
+include $(TOPDIR)/.config
+include $(TOPDIR)/tools/Config.mk
+include $(TOPDIR)/tools/esp32s3/Config.mk
+include $(TOPDIR)/arch/xtensa/src/lx7/Toolchain.defs
+
+ARCHSCRIPT += $(BOARD_COMMON_DIR)$(DELIM)scripts$(DELIM)esp32s3_peripherals.ld
+ARCHSCRIPT += $(BOARD_COMMON_DIR)$(DELIM)scripts$(DELIM)esp32s3_rom_aliases.ld
+
+# Pick the linker scripts from the board level if they exist, if not
+# pick the common linker scripts.
+
+ifeq ($(CONFIG_BUILD_PROTECTED),y)
+  ARCHSCRIPT += $(call FINDSCRIPT,protected_memory.ld)
+  ARCHSCRIPT += $(call FINDSCRIPT,kernel-space.ld)
+else
+  ARCHSCRIPT += $(call FINDSCRIPT,flat_memory.ld)
+  ifneq ($(CONFIG_ESP32S3_APP_FORMAT_LEGACY),y)
+    ARCHSCRIPT += $(call FINDSCRIPT,esp32s3_sections.ld)
+  else
+    ARCHSCRIPT += $(call FINDSCRIPT,legacy_sections.ld)
+  endif
+endif
+
+ifneq ($(CONFIG_DEBUG_NOOPT),y)
+  ARCHOPTIMIZATION += -fno-strength-reduce
+endif
+
+ARCHPICFLAGS = -fpic
+
+CFLAGS := $(ARCHCFLAGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRAFLAGS)
+CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
+CXXFLAGS := $(ARCHCXXFLAGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRAFLAGS)
+CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
+CPPFLAGS := $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRAFLAGS)
+AFLAGS := $(CFLAGS) -D__ASSEMBLY__

boards/xtensa/esp32s3/esp32s3-8048S043/src/Make.defs

@@ -0,0 +1,58 @@
+############################################################################
+# boards/xtensa/esp32s3/esp32s3-8048S043/src/Make.defs
+#
+# SPDX-License-Identifier: Apache-2.0
+#
+# Licensed to the Apache Software Foundation (ASF) under one or more
+# contributor license agreements.  See the NOTICE file distributed with
+# this work for additional information regarding copyright ownership.  The
+# ASF licenses this file to you under the Apache License, Version 2.0 (the
+# "License"); you may not use this file except in compliance with the
+# License.  You may obtain a copy of the License at
+#
+#   http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+# WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
+# License for the specific language governing permissions and limitations
+# under the License.
+#
+############################################################################
+
+CSRCS = esp32s3_boot.c esp32s3_bringup.c
+
+ifeq ($(CONFIG_BOARDCTL),y)
+CSRCS += esp32s3_appinit.c
+ifeq ($(CONFIG_BOARDCTL_RESET),y)
+CSRCS += esp32s3_reset.c
+endif
+endif
+
+ifeq ($(CONFIG_ARCH_BUTTONS),y)
+CSRCS += esp32s3_buttons.c
+endif
+
+ifeq ($(CONFIG_ESP32S3_SPI),y)
+CSRCS += esp32s3_board_spi.c
+endif
+
+ifeq ($(CONFIG_DEV_GPIO),y)
+CSRCS += esp32s3_gpio.c
+endif
+
+ifeq ($(CONFIG_ESP32S3_BOARD_TOUCHSCREEN),y)
+CSRCS += esp32s3_board_touchsceen.c
+endif
+
+DEPPATH += --dep-path board
+VPATH += :board
+CFLAGS += ${INCDIR_PREFIX}$(TOPDIR)$(DELIM)arch$(DELIM)$(CONFIG_ARCH)$(DELIM)src$(DELIM)board$(DELIM)board
+
+ifeq ($(CONFIG_ETC_ROMFS),y)
+RCSRCS  = etc/init.d/rc.sysinit etc/init.d/rcS
+
+ifeq ($(CONFIG_TXTABLE_PARTITION),y)
+RCRAWS  = etc/txtable.txt
+endif # CONFIG_TXTABLE_PARTITION
+endif

boards/xtensa/esp32s3/esp32s3-8048S043/src/esp32s3-8048S043.h

@@ -0,0 +1,148 @@
+/****************************************************************************
+ * boards/xtensa/esp32s3/esp32s3-8048S043/src/esp32s3-8048S043.h
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed to the Apache Software Foundation (ASF) under one or more
+ * contributor license agreements.  See the NOTICE file distributed with
+ * this work for additional information regarding copyright ownership.  The
+ * ASF licenses this file to you under the Apache License, Version 2.0 (the
+ * "License"); you may not use this file except in compliance with the
+ * License.  You may obtain a copy of the License at
+ *
+ *   http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
+ * License for the specific language governing permissions and limitations
+ * under the License.
+ *
+ ****************************************************************************/
+
+#ifndef __BOARDS_XTENSA_ESP32S3_ESP32S3_8048S043_SRC_ESP32S3_8048S043_H
+#define __BOARDS_XTENSA_ESP32S3_ESP32S3_8048S043_SRC_ESP32S3_8048S043_H
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+#include <nuttx/compiler.h>
+#include <stdint.h>
+
+/****************************************************************************
+ * Pre-processor Definitions
+ ****************************************************************************/
+
+/* ESP32-S3-8048S043 GPIOs **************************************************/
+
+/* Touchpad */
+#define TOUCHSCEEN_I2C 0
+
+/* SCL: 20
+ * SDA: 19
+ */
+
+#define TOUCHSCEEN_ADDR (0x5D)
+#define TOUCHSCEEN_CLOCK (400 * 1000)
+#define TOUCHSCEEN_INT (-1)
+
+/* BOOT Button */
+
+#define BUTTON_BOOT  0
+
+/****************************************************************************
+ * Public Types
+ ****************************************************************************/
+
+/****************************************************************************
+ * Public Data
+ ****************************************************************************/
+
+#ifndef __ASSEMBLY__
+
+/****************************************************************************
+ * Public Function Prototypes
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: esp32s3_bringup
+ *
+ * Description:
+ *   Perform architecture-specific initialization
+ *
+ *   CONFIG_BOARD_LATE_INITIALIZE=y :
+ *     Called from board_late_initialize().
+ *
+ *   CONFIG_BOARD_LATE_INITIALIZE=y && CONFIG_BOARDCTL=y :
+ *     Called from the NSH library via board_app_initialize()
+ *
+ ****************************************************************************/
+
+int esp32s3_bringup(void);
+
+/****************************************************************************
+ * Name: esp32s3_gpio_init
+ *
+ * Description:
+ *   Configure the GPIO driver.
+ *
+ * Returned Value:
+ *   Zero (OK) is returned on success; A negated errno value is returned
+ *   to indicate the nature of any failure.
+ *
+ ****************************************************************************/
+
+#ifdef CONFIG_DEV_GPIO
+int esp32s3_gpio_init(void);
+#endif
+
+/****************************************************************************
+ * Name: board_spiflash_init
+ *
+ * Description:
+ *   Initialize the SPIFLASH and register the MTD device.
+ *
+ ****************************************************************************/
+
+#ifdef CONFIG_ESP32S3_SPIFLASH
+int board_spiflash_init(void);
+#endif
+
+/****************************************************************************
+ * Name: board_i2c_init
+ *
+ * Description:
+ *   Configure the I2C driver.
+ *
+ * Returned Value:
+ *   Zero (OK) is returned on success; A negated errno value is returned
+ *   to indicate the nature of any failure.
+ *
+ ****************************************************************************/
+
+#ifdef CONFIG_I2C_DRIVER
+int board_i2c_init(void);
+#endif
+
+/****************************************************************************
+ * Name: board_touchscreen_initialize
+ *
+ * Description:
+ *   Initialize touchscreen.
+ *
+ * Input Parameters:
+ *   None.
+ *
+ * Returned Value:
+ *   Zero (OK) on success; a negated errno value on failure.
+ *
+ ****************************************************************************/
+
+#ifdef CONFIG_ESP32S3_BOARD_TOUCHSCREEN
+int board_touchscreen_initialize(void);
+#endif
+
+#endif /* __ASSEMBLY__ */
+#endif /* __BOARDS_XTENSA_ESP32S3_ESP32S3_8048S043_SRC_ESP32S3_8048S043_H */

boards/xtensa/esp32s3/esp32s3-8048S043/src/esp32s3_appinit.c

@@ -0,0 +1,82 @@
+/****************************************************************************
+ * boards/xtensa/esp32s3/esp32s3-8048S043/src/esp32s3_appinit.c
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed to the Apache Software Foundation (ASF) under one or more
+ * contributor license agreements.  See the NOTICE file distributed with
+ * this work for additional information regarding copyright ownership.  The
+ * ASF licenses this file to you under the Apache License, Version 2.0 (the
+ * "License"); you may not use this file except in compliance with the
+ * License.  You may obtain a copy of the License at
+ *
+ *   http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
+ * License for the specific language governing permissions and limitations
+ * under the License.
+ *
+ ****************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <sys/types.h>
+#include <nuttx/board.h>
+
+#include "esp32s3-8048S043.h"
+
+#ifdef CONFIG_BOARDCTL
+
+/****************************************************************************
+ * Pre-processor Definitions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: board_app_initialize
+ *
+ * Description:
+ *   Perform application specific initialization.  This function is never
+ *   called directly from application code, but only indirectly via the
+ *   (non-standard) boardctl() interface using the command BOARDIOC_INIT.
+ *
+ * Input Parameters:
+ *   arg - The boardctl() argument is passed to the board_app_initialize()
+ *         implementation without modification.  The argument has no
+ *         meaning to NuttX; the meaning of the argument is a contract
+ *         between the board-specific initialization logic and the
+ *         matching application logic.  The value could be such things as a
+ *         mode enumeration value, a set of DIP switch settings, a
+ *         pointer to configuration data read from a file or serial FLASH,
+ *         or whatever you would like to do with it.  Every implementation
+ *         should accept zero/NULL as a default configuration.
+ *
+ * Returned Value:
+ *   Zero (OK) is returned on success; a negated errno value is returned on
+ *   any failure to indicate the nature of the failure.
+ *
+ ****************************************************************************/
+
+int board_app_initialize(uintptr_t arg)
+{
+#ifdef CONFIG_BOARD_LATE_INITIALIZE
+  /* Board initialization already performed by board_late_initialize() */
+
+  return OK;
+#else
+  /* Perform board-specific initialization */
+
+  return esp32s3_bringup();
+#endif
+}
+
+#endif /* CONFIG_BOARDCTL */

boards/xtensa/esp32s3/esp32s3-8048S043/src/esp32s3_board_spi.c

@@ -0,0 +1,74 @@
+/****************************************************************************
+ * boards/xtensa/esp32s3/esp32s3-8048S043/src/esp32s3_board_spi.c
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed to the Apache Software Foundation (ASF) under one or more
+ * contributor license agreements.  See the NOTICE file distributed with
+ * this work for additional information regarding copyright ownership.  The
+ * ASF licenses this file to you under the Apache License, Version 2.0 (the
+ * "License"); you may not use this file except in compliance with the
+ * License.  You may obtain a copy of the License at
+ *
+ *   http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
+ * License for the specific language governing permissions and limitations
+ * under the License.
+ *
+ ****************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <stdint.h>
+#include <stdbool.h>
+#include <debug.h>
+
+#include <nuttx/spi/spi.h>
+
+#include "esp32s3_gpio.h"
+#include "esp32s3-8048S043.h"
+
+/****************************************************************************
+ * Private Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: esp32s3_spi2_status
+ ****************************************************************************/
+
+#ifdef CONFIG_ESP32S3_SPI2
+
+uint8_t esp32s3_spi2_status(struct spi_dev_s *dev, uint32_t devid)
+{
+  uint8_t status = 0;
+
+  return status;
+}
+
+#endif
+
+/****************************************************************************
+ * Name: esp32s3_spi3_status
+ ****************************************************************************/
+
+#ifdef CONFIG_ESP32S3_SPI3
+
+uint8_t esp32s3_spi3_status(struct spi_dev_s *dev, uint32_t devid)
+{
+  uint8_t status = 0;
+
+  return status;
+}
+
+#endif

boards/xtensa/esp32s3/esp32s3-8048S043/src/esp32s3_board_touchsceen.c

@@ -0,0 +1,450 @@
+/****************************************************************************
+ * boards/xtensa/esp32s3/esp32s3-8048S043/src/esp32s3_board_touchsceen.c
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed to the Apache Software Foundation (ASF) under one or more
+ * contributor license agreements.  See the NOTICE file distributed with
+ * this work for additional information regarding copyright ownership.  The
+ * ASF licenses this file to you under the Apache License, Version 2.0 (the
+ * "License"); you may not use this file except in compliance with the
+ * License.  You may obtain a copy of the License at
+ *
+ *   http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
+ * License for the specific language governing permissions and limitations
+ * under the License.
+ *
+ ****************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <syslog.h>
+#include <assert.h>
+#include <errno.h>
+#include <debug.h>
+#include <string.h>
+#include <nuttx/spinlock.h>
+#include <nuttx/wqueue.h>
+#include <nuttx/input/touchscreen.h>
+
+#include "esp32s3_i2c.h"
+#include "esp32s3_gpio.h"
+#include "hardware/esp32s3_gpio_sigmap.h"
+
+#include "esp32s3-8048S043.h"
+
+/****************************************************************************
+ * Pre-processor Definitions
+ ****************************************************************************/
+
+/* GT911 maximum report frame size */
+
+#define GT911_BUFFER_SIZE     41
+#define GT911_TOUCHPOINTS     5
+
+/* GT911 board configuration */
+
+#define GT911_ADDR            TOUCHSCEEN_ADDR
+#define GT911_CLOCK           TOUCHSCEEN_CLOCK
+
+#define GT911_PATH            CONFIG_ESP32S3_BOARD_TOUCHSCREEN_PATH
+#define GT911_WORK_DELAY      CONFIG_ESP32S3_BOARD_TOUCHSCREEN_SAMPLE_DELAYS
+#define GT911_SAMPLE_CACHES   CONFIG_ESP32S3_BOARD_TOUCHSCREEN_SAMPLE_CACHES
+
+/* GT911 registers address */
+
+#define GT911_READ_XY_REG     0x814e
+#define GT911_READ_DATA_REG   0x814f
+#define GT911_CONFIG_REG      0x8047
+#define GT911_PRODUCT_ID_REG  0x8140
+
+/****************************************************************************
+ * Private Types
+ ****************************************************************************/
+
+/* This structure describes the state of one GT911 driver instance */
+
+struct gt911_dev_s
+{
+  struct touch_lowerhalf_s  touch_lower;    /* Touchsrceen lowerhalf */
+
+  bool                has_report;           /* Mark if report event */
+
+  struct i2c_master_s *i2c;                 /* I2C master port */
+  struct work_s       work;                 /* Read sample data work */
+  spinlock_t          lock;                 /* Device specific lock. */
+
+  uint8_t buffer[GT911_BUFFER_SIZE];        /* Read buffer */
+};
+
+/* This structure describes the frame of touchpoint */
+
+begin_packed_struct struct gt911_touchpoint_s
+{
+  uint8_t id;                               /* Not used */
+  uint16_t x;                               /* Touch X-axis */
+  uint16_t y;                               /* Touch Y-axis */
+  uint16_t pressure;                        /* Touch pressure */
+  uint8_t  reserved;                        /* Not used */
+} end_packed_struct;
+
+/* This structure describes the frame of touchpoint */
+
+begin_packed_struct struct gt911_data_s
+{
+  uint8_t touchpoints     : 4;              /* Touch point number */
+  uint8_t has_key         : 1;              /* 1: key is inpressed */
+  uint8_t proximity_valid : 1;              /* Not used */
+  uint8_t large_detected  : 1;              /* 1: large-area touch */
+  uint8_t buffer_status   : 1;              /* 1: input data is valid */
+
+  struct gt911_touchpoint_s touchpoint[0];
+} end_packed_struct;
+
+/****************************************************************************
+ * Private Data
+ ****************************************************************************/
+
+struct gt911_dev_s g_gt911_dev;
+
+/****************************************************************************
+ * Private Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: gt911_write_reg
+ *
+ * Description:
+ *   Read GT911 continuous registers value.
+ *
+ * Input Parameters:
+ *   dev    - GT911 object pointer
+ *   reg    - Register start address
+ *   buf    - Register value buffer
+ *   buflen - Register value buffer length
+ *
+ * Returned Value:
+ *   Zero (OK) on success; a negated errno value on failure.
+ *
+ ****************************************************************************/
+
+static int gt911_read_reg(struct gt911_dev_s *dev,
+                          uint16_t reg,
+                          uint8_t *buf,
+                          int buflen)
+{
+  int ret;
+
+  /* Send the Register Address, MSB first */
+
+  uint8_t regbuf[2] =
+  {
+    reg >> 8,   /* First Byte: MSB */
+    reg & 0xff  /* Second Byte: LSB */
+  };
+
+  /* Compose the I2C Messages */
+
+  struct i2c_msg_s msgv[2] =
+  {
+    {
+      /* Send the I2C Register Address */
+
+      .frequency = GT911_CLOCK,
+      .addr      = GT911_ADDR,
+      .flags     = 0,
+      .buffer    = regbuf,
+      .length    = sizeof(regbuf)
+    },
+    {
+      /* Receive the I2C Register Values */
+
+      .frequency = GT911_CLOCK,
+      .addr      = GT911_ADDR,
+      .flags     = I2C_M_READ,
+      .buffer    = buf,
+      .length    = buflen
+    }
+  };
+
+  const int msgv_len = sizeof(msgv) / sizeof(msgv[0]);
+
+  iinfo("reg=0x%x, buflen=%d\n", reg, buflen);
+  DEBUGASSERT(dev && dev->i2c && buf);
+
+  /* Execute the I2C Transfer */
+
+  ret = I2C_TRANSFER(dev->i2c, msgv, msgv_len);
+  if (ret < 0)
+    {
+      ierr("I2C Read failed: %d\n", ret);
+      return ret;
+    }
+
+#ifdef CONFIG_DEBUG_INPUT_INFO
+  iinfodumpbuffer("gt911_read_reg", buf, buflen);
+#endif /* CONFIG_DEBUG_INPUT_INFO */
+
+  return 0;
+}
+
+/****************************************************************************
+ * Name: gt911_write_reg
+ *
+ * Description:
+ *   Write GT911 register value.
+ *
+ * Input Parameters:
+ *   dev - GT911 object pointer
+ *   reg - Register address
+ *   val - Register value
+ *
+ * Returned Value:
+ *   Zero (OK) on success; a negated errno value on failure.
+ *
+ ****************************************************************************/
+
+static int gt911_write_reg(struct gt911_dev_s *dev,
+                           uint16_t reg,
+                           uint8_t val)
+{
+  int ret;
+
+  /* Send the Register Address, MSB first */
+
+  uint8_t regbuf[3] =
+  {
+    reg >> 8,   /* First Byte: MSB */
+    reg & 0xff, /* Second Byte: LSB */
+    val,
+  };
+
+  /* Compose the I2C Messages */
+
+  struct i2c_msg_s msgv[1] =
+  {
+    {
+      /* Send the I2C Register Address */
+
+      .frequency = GT911_CLOCK,
+      .addr      = GT911_ADDR,
+      .flags     = 0,
+      .buffer    = regbuf,
+      .length    = sizeof(regbuf)
+    }
+  };
+
+  const int msgv_len = sizeof(msgv) / sizeof(msgv[0]);
+
+  iinfo("reg=0x%x, val=%d\n", reg, val);
+  DEBUGASSERT(dev && dev->i2c);
+
+  /* Execute the I2C Transfer */
+
+  ret = I2C_TRANSFER(dev->i2c, msgv, msgv_len);
+  if (ret < 0)
+    {
+      ierr("I2C Write failed: %d\n", ret);
+      return ret;
+    }
+
+  return 0;
+}
+
+/****************************************************************************
+ * Name: gt911_touch_event
+ *
+ * Description:
+ *   Process touch event. Read touchpoint data and send to touch event.
+ *
+ * Input Parameters:
+ *   dev - GT911 object pointer
+ *
+ * Returned Value:
+ *   None
+ *
+ ****************************************************************************/
+
+static void gt911_touch_event(struct gt911_dev_s *dev)
+{
+  struct gt911_data_s *data = (struct gt911_data_s *)dev->buffer;
+  struct gt911_touchpoint_s *tp = data->touchpoint;
+  struct touch_sample_s sample;
+  struct touch_point_s *point = sample.point;
+
+  memset(&sample, 0, sizeof(sample));
+  sample.npoints = 1;
+
+  point->x         = tp->x;
+  point->y         = tp->y;
+  point->pressure  = tp->pressure;
+  point->flags     = TOUCH_POS_VALID | TOUCH_PRESSURE_VALID;
+
+  if (data->buffer_status)
+    {
+      point->flags |= TOUCH_DOWN;
+      dev->has_report = true;
+    }
+  else
+    {
+      point->flags |= TOUCH_UP;
+      dev->has_report = false;
+    }
+
+  touch_event(dev->touch_lower.priv, &sample);
+}
+
+/****************************************************************************
+ * Name: gt911_event
+ *
+ * Description:
+ *   Process GT911 event.
+ *
+ * Input Parameters:
+ *   dev - GT911 object pointer
+ *
+ * Returned Value:
+ *   None
+ *
+ ****************************************************************************/
+
+static void gt911_event(struct gt911_dev_s *dev)
+{
+  struct gt911_data_s *data = (struct gt911_data_s *)dev->buffer;
+
+  if (!data->has_key)
+    {
+      gt911_touch_event(dev);
+    }
+  else
+    {
+      ierr("ERROR: event is invalid\n");
+    }
+}
+
+/****************************************************************************
+ * Name: gt911_worker
+ *
+ * Description:
+ *   Process GT911 work, read GT911 report frame and process it.
+ *
+ * Input Parameters:
+ *   arg - GT911 object pointer
+ *
+ * Returned Value:
+ *   None
+ *
+ ****************************************************************************/
+
+static void gt911_worker(void *arg)
+{
+  int ret;
+  struct gt911_dev_s *dev = (struct gt911_dev_s *)arg;
+  struct gt911_data_s *data = (struct gt911_data_s *)dev->buffer;
+  clock_t delay = GT911_WORK_DELAY;
+  bool touched = false;
+
+  ret = gt911_read_reg(dev, GT911_READ_XY_REG, dev->buffer, 1);
+  if (ret != 0)
+    {
+      ierr("ERROR: I2C_TRANSFER() failed: %d\n", ret);
+      goto exit;
+    }
+
+  if (data->buffer_status &&
+      (data->touchpoints > 0) &&
+      (data->touchpoints < GT911_TOUCHPOINTS))
+    {
+      ret = gt911_read_reg(dev, GT911_READ_DATA_REG,
+                           &dev->buffer[1], data->touchpoints * 8);
+      if (ret != 0)
+        {
+          ierr("ERROR: I2C_TRANSFER() failed: %d\n", ret);
+          goto exit;
+        }
+
+      touched = true;
+    }
+  else if (dev->has_report)
+    {
+      touched = true;
+    }
+
+  ret = gt911_write_reg(dev, GT911_READ_XY_REG, 0);
+  if (ret != 0)
+    {
+      ierr("ERROR: I2C_TRANSFER() failed: %d\n", ret);
+      goto exit;
+    }
+
+  if (touched)
+    {
+      gt911_event(dev);
+      delay = 1;
+    }
+
+exit:
+  ret = work_queue(LPWORK, &dev->work, gt911_worker, dev, delay);
+  if (ret != 0)
+    {
+      ierr("ERROR: work_queue() failed: %d\n", ret);
+    }
+}
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: board_touchscreen_initialize
+ *
+ * Description:
+ *   Initialize touchpad.
+ *
+ * Input Parameters:
+ *   None.
+ *
+ * Returned Value:
+ *   Zero (OK) on success; a negated errno value on failure.
+ *
+ ****************************************************************************/
+
+int board_touchscreen_initialize(void)
+{
+  int ret;
+  struct gt911_dev_s *dev = &g_gt911_dev;
+
+  dev->i2c = esp32s3_i2cbus_initialize(TOUCHSCEEN_I2C);
+  if (!dev->i2c)
+    {
+      syslog(LOG_ERR, "ERROR: Failed to initialize I2C port %d\n",
+             TOUCHSCEEN_I2C);
+      return -ENODEV;
+    }
+
+  ret = touch_register(&dev->touch_lower, GT911_PATH,
+                       GT911_SAMPLE_CACHES);
+  if (ret < 0)
+    {
+      syslog(LOG_ERR, "ERROR: touch_register() failed: %d\n", ret);
+      return ret;
+    }
+
+  ret = work_queue(LPWORK, &dev->work, gt911_worker,
+                   dev, GT911_WORK_DELAY);
+  if (ret != 0)
+    {
+      syslog(LOG_ERR, "ERROR: work_queue() failed: %d\n", ret);
+      return ret;
+    }
+
+  return 0;
+}

boards/xtensa/esp32s3/esp32s3-8048S043/src/esp32s3_boot.c

@@ -0,0 +1,85 @@
+/****************************************************************************
+ * boards/xtensa/esp32s3/esp32s3-8048S043/src/esp32s3_boot.c
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed to the Apache Software Foundation (ASF) under one or more
+ * contributor license agreements.  See the NOTICE file distributed with
+ * this work for additional information regarding copyright ownership.  The
+ * ASF licenses this file to you under the Apache License, Version 2.0 (the
+ * "License"); you may not use this file except in compliance with the
+ * License.  You may obtain a copy of the License at
+ *
+ *   http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
+ * License for the specific language governing permissions and limitations
+ * under the License.
+ *
+ ****************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <debug.h>
+
+#include <nuttx/board.h>
+#include <nuttx/mm/mm.h>
+#include <arch/board/board.h>
+
+#include "esp32s3-8048S043.h"
+
+/****************************************************************************
+ * Pre-processor Definitions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Private Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: esp32s3_board_initialize
+ *
+ * Description:
+ *   All ESP32-S3 boards must provide the following entry point.
+ *   This entry point is called early in the initialization -- after all
+ *   memory has been configured and mapped but before any devices have been
+ *   initialized.
+ *
+ ****************************************************************************/
+
+void esp32s3_board_initialize(void)
+{
+}
+
+/****************************************************************************
+ * Name: board_late_initialize
+ *
+ * Description:
+ *   If CONFIG_BOARD_LATE_INITIALIZE is selected, then an additional
+ *   initialization call will be performed in the boot-up sequence to a
+ *   function called board_late_initialize().  board_late_initialize() will
+ *   be called immediately after up_initialize() is called and just before
+ *   the initial application is started.  This additional initialization
+ *   phase may be used, for example, to initialize board-specific device
+ *   drivers.
+ *
+ ****************************************************************************/
+
+#ifdef CONFIG_BOARD_LATE_INITIALIZE
+void board_late_initialize(void)
+{
+  /* Perform board-specific initialization */
+
+  esp32s3_bringup();
+}
+#endif

boards/xtensa/esp32s3/esp32s3-8048S043/src/esp32s3_bringup.c

@@ -0,0 +1,265 @@
+/****************************************************************************
+ * boards/xtensa/esp32s3/esp32s3-8048S043/src/esp32s3_bringup.c
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed to the Apache Software Foundation (ASF) under one or more
+ * contributor license agreements.  See the NOTICE file distributed with
+ * this work for additional information regarding copyright ownership.  The
+ * ASF licenses this file to you under the Apache License, Version 2.0 (the
+ * "License"); you may not use this file except in compliance with the
+ * License.  You may obtain a copy of the License at
+ *
+ *   http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
+ * License for the specific language governing permissions and limitations
+ * under the License.
+ *
+ ****************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <fcntl.h>
+#include <unistd.h>
+#include <syslog.h>
+#include <sys/stat.h>
+#include <sys/ioctl.h>
+#include <sys/types.h>
+#include <debug.h>
+#include <stdio.h>
+
+#include <errno.h>
+#include <nuttx/fs/fs.h>
+#include <nuttx/himem/himem.h>
+#include <arch/board/board.h>
+
+#ifdef CONFIG_ESP32S3_I2C
+#  include "esp32s3_i2c.h"
+#endif
+
+#ifdef CONFIG_INPUT_BUTTONS
+#  include <nuttx/input/buttons.h>
+#endif
+
+#ifdef CONFIG_RTC_DRIVER
+#  include "esp32s3_rtc_lowerhalf.h"
+#endif
+
+#ifdef CONFIG_ESP32S3_EFUSE
+#  include "esp32s3_efuse.h"
+#endif
+
+#ifdef CONFIG_ESP32S3_PARTITION_TABLE
+#  include "esp32s3_partition.h"
+#endif
+
+#ifdef CONFIG_ESP32S3_SPI
+#include "esp32s3_spi.h"
+#include "esp32s3_board_spidev.h"
+#  ifdef CONFIG_ESPRESSIF_SPI_BITBANG
+#    include "espressif/esp_spi_bitbang.h"
+#  endif
+#endif
+
+#ifdef CONFIG_ESP32S3_SDMMC
+#include "esp32s3_board_sdmmc.h"
+#endif
+
+#ifdef CONFIG_ESPRESSIF_TEMP
+#  include "espressif/esp_temperature_sensor.h"
+#endif
+
+#ifdef CONFIG_ESP_PCNT
+#  include "espressif/esp_pcnt.h"
+#  include "esp32s3_board_pcnt.h"
+#endif
+
+#ifdef CONFIG_SYSTEM_NXDIAG_ESPRESSIF_CHIP_WO_TOOL
+#  include "espressif/esp_nxdiag.h"
+#endif
+
+#include "esp32s3-8048S043.h"
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: esp32s3_bringup
+ *
+ * Description:
+ *   Perform architecture-specific initialization
+ *
+ *   CONFIG_BOARD_LATE_INITIALIZE=y :
+ *     Called from board_late_initialize().
+ *
+ *   CONFIG_BOARD_LATE_INITIALIZE=n && CONFIG_BOARDCTL=y :
+ *     Called from the NSH library
+ *
+ ****************************************************************************/
+
+int esp32s3_bringup(void)
+{
+  int ret;
+
+#if defined(CONFIG_ESP32S3_SPIRAM) && \
+    defined(CONFIG_ESP32S3_SPIRAM_BANKSWITCH_ENABLE)
+  ret = esp_himem_init();
+  if (ret < 0)
+    {
+      syslog(LOG_ERR, "ERROR: Failed to init HIMEM: %d\n", ret);
+    }
+#endif
+
+#if defined(CONFIG_ESP32S3_SPI) && defined(CONFIG_SPI_DRIVER)
+  #ifdef CONFIG_ESP32S3_SPI2
+  ret = board_spidev_initialize(ESP32S3_SPI2);
+  if (ret < 0)
+    {
+      syslog(LOG_ERR, "ERROR: Failed to init spidev 2: %d\n", ret);
+    }
+  #endif
+
+  #ifdef CONFIG_ESP32S3_SPI3
+  ret = board_spidev_initialize(ESP32S3_SPI3);
+  if (ret < 0)
+    {
+      syslog(LOG_ERR, "ERROR: Failed to init spidev 3: %d\n", ret);
+    }
+  #endif
+
+  #ifdef CONFIG_ESPRESSIF_SPI_BITBANG
+  ret = board_spidev_initialize(ESPRESSIF_SPI_BITBANG);
+  if (ret < 0)
+    {
+      syslog(LOG_ERR, "ERROR: Failed to init spidev 3: %d\n", ret);
+    }
+  #endif /* CONFIG_ESPRESSIF_SPI_BITBANG */
+#endif /* CONFIG_ESP32S3_SPI && CONFIG_SPI_DRIVER*/
+
+#if defined(CONFIG_ESP32S3_EFUSE)
+  ret = esp32s3_efuse_initialize("/dev/efuse");
+  if (ret < 0)
+    {
+      syslog(LOG_ERR, "ERROR: Failed to init EFUSE: %d\n", ret);
+    }
+#endif
+
+#ifdef CONFIG_FS_PROCFS
+  /* Mount the procfs file system */
+
+  ret = nx_mount(NULL, "/proc", "procfs", 0, NULL);
+  if (ret < 0)
+    {
+      syslog(LOG_ERR, "ERROR: Failed to mount procfs at /proc: %d\n", ret);
+    }
+#endif
+
+#ifdef CONFIG_FS_TMPFS
+  /* Mount the tmpfs file system */
+
+  ret = nx_mount(NULL, CONFIG_LIBC_TMPDIR, "tmpfs", 0, NULL);
+  if (ret < 0)
+    {
+      syslog(LOG_ERR, "ERROR: Failed to mount tmpfs at %s: %d\n",
+             CONFIG_LIBC_TMPDIR, ret);
+    }
+#endif
+
+#ifdef CONFIG_ESP32S3_PARTITION_TABLE
+  ret = esp32s3_partition_init();
+  if (ret < 0)
+    {
+      syslog(LOG_ERR, "ERROR: Failed to initialize partition error=%d\n",
+             ret);
+    }
+#endif
+
+#ifdef CONFIG_ESPRESSIF_TEMP
+  struct esp_temp_sensor_config_t cfg = TEMPERATURE_SENSOR_CONFIG(10, 50);
+  ret = esp_temperature_sensor_initialize(cfg);
+  if (ret < 0)
+    {
+      syslog(LOG_ERR, "Failed to initialize temperature sensor driver: %d\n",
+             ret);
+    }
+#endif
+
+#ifdef CONFIG_RTC_DRIVER
+  /* Instantiate the ESP32-S3 RTC driver */
+
+  ret = esp32s3_rtc_driverinit();
+  if (ret < 0)
+    {
+      syslog(LOG_ERR,
+             "ERROR: Failed to Instantiate the RTC driver: %d\n", ret);
+    }
+#endif
+
+#ifdef CONFIG_I2C_DRIVER
+  /* Configure I2C peripheral interfaces */
+
+  ret = board_i2c_init();
+  if (ret < 0)
+    {
+      syslog(LOG_ERR, "Failed to initialize I2C driver: %d\n", ret);
+    }
+#endif
+
+#ifdef CONFIG_INPUT_BUTTONS
+  /* Register the BUTTON driver */
+
+  ret = btn_lower_initialize("/dev/buttons");
+  if (ret < 0)
+    {
+      syslog(LOG_ERR, "Failed to initialize button driver: %d\n", ret);
+    }
+#endif
+
+#if defined(CONFIG_DEV_GPIO) && !defined(CONFIG_GPIO_LOWER_HALF)
+  ret = esp32s3_gpio_init();
+  if (ret < 0)
+    {
+      syslog(LOG_ERR, "Failed to initialize GPIO Driver: %d\n", ret);
+    }
+#endif
+
+#ifdef CONFIG_ESP32S3_SDMMC
+  ret = board_sdmmc_initialize();
+  if (ret < 0)
+    {
+      syslog(LOG_ERR, "ERROR: Failed to initialize SDMMC: %d\n", ret);
+    }
+#endif
+
+#ifdef CONFIG_SYSTEM_NXDIAG_ESPRESSIF_CHIP_WO_TOOL
+  ret = esp_nxdiag_initialize();
+  if (ret < 0)
+    {
+      syslog(LOG_ERR, "ERROR: esp_nxdiag_initialize failed: %d\n", ret);
+    }
+#endif
+
+#ifdef CONFIG_ESP32S3_BOARD_TOUCHSCREEN
+  ret = board_touchscreen_initialize();
+  if (ret < 0)
+    {
+      syslog(LOG_ERR, "Failed to initialize touchscreen driver\n");
+    }
+#endif
+
+  /* If we got here then perhaps not all initialization was successful, but
+   * at least enough succeeded to bring-up NSH with perhaps reduced
+   * capabilities.
+   */
+
+  UNUSED(ret);
+  return OK;
+}

boards/xtensa/esp32s3/esp32s3-8048S043/src/esp32s3_buttons.c

@@ -0,0 +1,166 @@
+/****************************************************************************
+ * boards/xtensa/esp32s3/esp32s3-8048S043/src/esp32s3_buttons.c
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed to the Apache Software Foundation (ASF) under one or more
+ * contributor license agreements.  See the NOTICE file distributed with
+ * this work for additional information regarding copyright ownership.  The
+ * ASF licenses this file to you under the Apache License, Version 2.0 (the
+ * "License"); you may not use this file except in compliance with the
+ * License.  You may obtain a copy of the License at
+ *
+ *   http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
+ * License for the specific language governing permissions and limitations
+ * under the License.
+ *
+ ****************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <assert.h>
+#include <debug.h>
+#include <stdbool.h>
+
+#include <nuttx/arch.h>
+#include <nuttx/board.h>
+#include <nuttx/irq.h>
+
+#include "esp32s3_gpio.h"
+#include "hardware/esp32s3_gpio_sigmap.h"
+
+#include "esp32s3-8048S043.h"
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: board_button_initialize
+ *
+ * Description:
+ *   board_button_initialize() must be called to initialize button resources.
+ *   After that, board_buttons() may be called to collect the current state
+ *   of all buttons or board_button_irq() may be called to register button
+ *   interrupt handlers.
+ *
+ ****************************************************************************/
+
+uint32_t board_button_initialize(void)
+{
+  esp32s3_configgpio(BUTTON_BOOT, INPUT_FUNCTION_2 | PULLUP);
+  return 1;
+}
+
+/****************************************************************************
+ * Name: board_buttons
+ *
+ * Description:
+ *   After board_button_initialize() has been called, board_buttons() may be
+ *   called to collect the state of all buttons.  board_buttons() returns an
+ *   8-bit bit set with each bit associated with a button.  See the
+ *   BUTTON_*_BIT  definitions in board.h for the meaning of each bit.
+ *
+ ****************************************************************************/
+
+uint32_t board_buttons(void)
+{
+  uint8_t ret = 0;
+  int i = 0;
+  int n = 0;
+
+  bool b0 = esp32s3_gpioread(BUTTON_BOOT);
+
+  for (i = 0; i < 10; i++)
+    {
+      up_mdelay(1);
+
+      bool b1 = esp32s3_gpioread(BUTTON_BOOT);
+
+      if (b0 == b1)
+        {
+          n++;
+        }
+      else
+        {
+          n = 0;
+        }
+
+      if (3 == n)
+        {
+          break;
+        }
+
+      b0 = b1;
+    }
+
+  iinfo("b=%d n=%d\n", b0, n);
+
+  /* Low value means that the button is pressed */
+
+  if (!b0)
+    {
+      ret = 0x1;
+    }
+
+  return ret;
+}
+
+/****************************************************************************
+ * Name: board_button_irq
+ *
+ * Description:
+ *   board_button_irq() may be called to register an interrupt handler that
+ *   will be called when a button is depressed or released.  The ID value is
+ *   a button enumeration value that uniquely identifies a button resource.
+ *   See the BUTTON_* definitions in board.h for the meaning of enumeration
+ *   value.
+ *
+ ****************************************************************************/
+
+#ifdef CONFIG_ARCH_IRQBUTTONS
+int board_button_irq(int id, xcpt_t irqhandler, void *arg)
+{
+  int ret;
+  DEBUGASSERT(id == 0);
+
+  int irq = ESP32S3_PIN2IRQ(BUTTON_BOOT);
+
+  if (irqhandler != NULL)
+    {
+      /* Make sure the interrupt is disabled */
+
+      esp32s3_gpioirqdisable(irq);
+
+      ret = irq_attach(irq, irqhandler, arg);
+      if (ret < 0)
+        {
+          syslog(LOG_ERR, "ERROR: irq_attach() failed: %d\n", ret);
+          return ret;
+        }
+
+      gpioinfo("Attach %p\n", irqhandler);
+
+      gpioinfo("Enabling the interrupt\n");
+
+      /* Configure the interrupt for rising and falling edges */
+
+      esp32s3_gpioirqenable(irq, CHANGE);
+    }
+  else
+    {
+      gpioinfo("Disable the interrupt\n");
+      esp32s3_gpioirqdisable(irq);
+    }
+
+  return OK;
+}
+#endif

boards/xtensa/esp32s3/esp32s3-8048S043/src/esp32s3_gpio.c

@@ -0,0 +1,435 @@
+/****************************************************************************
+ * boards/xtensa/esp32s3/esp32s3-8048S043/src/esp32s3_gpio.c
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed to the Apache Software Foundation (ASF) under one or more
+ * contributor license agreements.  See the NOTICE file distributed with
+ * this work for additional information regarding copyright ownership.  The
+ * ASF licenses this file to you under the Apache License, Version 2.0 (the
+ * "License"); you may not use this file except in compliance with the
+ * License.  You may obtain a copy of the License at
+ *
+ *   http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
+ * License for the specific language governing permissions and limitations
+ * under the License.
+ *
+ ****************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <sys/types.h>
+#include <nuttx/irq.h>
+#include <arch/irq.h>
+#include <assert.h>
+#include <debug.h>
+
+#include <nuttx/ioexpander/gpio.h>
+
+#include <arch/board/board.h>
+
+#include "esp32s3-8048S043.h"
+#include "esp32s3_gpio.h"
+#include "hardware/esp32s3_gpio_sigmap.h"
+
+#ifdef CONFIG_ESPRESSIF_DEDICATED_GPIO
+#include "espressif/esp_dedic_gpio.h"
+#endif
+
+#if defined(CONFIG_DEV_GPIO) && !defined(CONFIG_GPIO_LOWER_HALF)
+
+/****************************************************************************
+ * Pre-processor Definitions
+ ****************************************************************************/
+
+#if !defined(CONFIG_ESP32S3_GPIO_IRQ) && BOARD_NGPIOINT > 0
+#  error "NGPIOINT is > 0 and GPIO interrupts aren't enabled"
+#endif
+
+/* Output pins. GPIO15 is used as an example, any other outputs could be
+ * used.
+ */
+
+#define GPIO_OUT1    15
+
+/* Input pins. GPIO18 is used as an example, any other inputs could be
+ * used.
+ */
+
+#define GPIO_IN1     18
+
+/* Interrupt pins. GPIO21 is used as an example, any other inputs could be
+ * used.
+ */
+
+#define GPIO_IRQPIN1 21
+
+/* Dedicated GPIO pins. GPIO4 and GPIO5 is used as an example, any other
+ * GPIOs could be used.
+ */
+
+#define GPIO_DEDIC1       4
+#define GPIO_DEDIC2       5
+#define GPIO_DEDIC_COUNT  2
+
+/****************************************************************************
+ * Private Types
+ ****************************************************************************/
+
+struct esp32s3gpio_dev_s
+{
+  struct gpio_dev_s gpio;
+  uint8_t id;
+};
+
+struct esp32s3gpint_dev_s
+{
+  struct esp32s3gpio_dev_s esp32s3gpio;
+  pin_interrupt_t callback;
+};
+
+/****************************************************************************
+ * Private Function Prototypes
+ ****************************************************************************/
+
+#if BOARD_NGPIOOUT > 0
+static int gpout_read(struct gpio_dev_s *dev, bool *value);
+static int gpout_write(struct gpio_dev_s *dev, bool value);
+#endif
+
+#if BOARD_NGPIOIN > 0
+static int gpin_read(struct gpio_dev_s *dev, bool *value);
+#endif
+
+#if BOARD_NGPIOINT > 0
+static int gpint_read(struct gpio_dev_s *dev, bool *value);
+static int gpint_attach(struct gpio_dev_s *dev,
+                        pin_interrupt_t callback);
+static int gpint_enable(struct gpio_dev_s *dev, bool enable);
+#endif
+
+/****************************************************************************
+ * Private Data
+ ****************************************************************************/
+
+#if BOARD_NGPIOOUT > 0
+static const struct gpio_operations_s gpout_ops =
+{
+  .go_read   = gpout_read,
+  .go_write  = gpout_write,
+  .go_attach = NULL,
+  .go_enable = NULL,
+};
+
+/* This array maps the GPIO pins used as OUTPUT */
+
+static const uint32_t g_gpiooutputs[BOARD_NGPIOOUT] =
+{
+  GPIO_OUT1
+};
+
+static struct esp32s3gpio_dev_s g_gpout[BOARD_NGPIOOUT];
+#endif
+
+#if BOARD_NGPIOIN > 0
+static const struct gpio_operations_s gpin_ops =
+{
+  .go_read   = gpin_read,
+  .go_write  = NULL,
+  .go_attach = NULL,
+  .go_enable = NULL,
+};
+
+/* This array maps the GPIO pins used as INTERRUPT INPUTS */
+
+static const uint32_t g_gpioinputs[BOARD_NGPIOIN] =
+{
+  GPIO_IN1
+};
+
+static struct esp32s3gpio_dev_s g_gpin[BOARD_NGPIOIN];
+#endif
+
+#if BOARD_NGPIOINT > 0
+static const struct gpio_operations_s gpint_ops =
+{
+  .go_read   = gpint_read,
+  .go_write  = NULL,
+  .go_attach = gpint_attach,
+  .go_enable = gpint_enable,
+};
+
+/* This array maps the GPIO pins used as INTERRUPT INPUTS */
+
+static const uint32_t g_gpiointinputs[BOARD_NGPIOINT] =
+{
+  GPIO_IRQPIN1,
+};
+
+static struct esp32s3gpint_dev_s g_gpint[BOARD_NGPIOINT];
+#endif
+
+/* This array maps the GPIO pins used as Dedicated GPIO */
+
+#ifdef CONFIG_ESPRESSIF_DEDICATED_GPIO
+static const int g_gpioidedic[GPIO_DEDIC_COUNT] =
+{
+  GPIO_DEDIC1, GPIO_DEDIC2
+};
+
+static struct esp_dedic_gpio_flags_s dedic_gpio_flags =
+{
+  .input_enable = 1,
+  .invert_input_enable = 0,
+  .output_enable = 1,
+  .invert_output_enable = 0
+};
+
+struct esp_dedic_gpio_config_s dedic_gpio_conf =
+{
+  .gpio_array = g_gpioidedic,
+  .array_size = GPIO_DEDIC_COUNT,
+  .flags = &dedic_gpio_flags,
+  .path = "/dev/dedic_gpio0"
+};
+
+struct file *dedicated_gpio = NULL;
+#endif
+
+/****************************************************************************
+ * Private Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: gpout_read
+ ****************************************************************************/
+
+#if BOARD_NGPIOOUT > 0
+static int gpout_read(struct gpio_dev_s *dev, bool *value)
+{
+  struct esp32s3gpio_dev_s *esp32s3gpio = (struct esp32s3gpio_dev_s *)dev;
+
+  DEBUGASSERT(esp32s3gpio != NULL && value != NULL);
+  DEBUGASSERT(esp32s3gpio->id < BOARD_NGPIOOUT);
+  gpioinfo("Reading...\n");
+
+  *value = esp32s3_gpioread(g_gpiooutputs[esp32s3gpio->id]);
+  return OK;
+}
+
+/****************************************************************************
+ * Name: gpout_write
+ ****************************************************************************/
+
+static int gpout_write(struct gpio_dev_s *dev, bool value)
+{
+  struct esp32s3gpio_dev_s *esp32s3gpio = (struct esp32s3gpio_dev_s *)dev;
+
+  DEBUGASSERT(esp32s3gpio != NULL);
+  DEBUGASSERT(esp32s3gpio->id < BOARD_NGPIOOUT);
+  gpioinfo("Writing %d\n", (int)value);
+
+  esp32s3_gpiowrite(g_gpiooutputs[esp32s3gpio->id], value);
+  return OK;
+}
+#endif
+
+/****************************************************************************
+ * Name: gpin_read
+ ****************************************************************************/
+
+#if BOARD_NGPIOIN > 0
+static int gpin_read(struct gpio_dev_s *dev, bool *value)
+{
+  struct esp32s3gpio_dev_s *esp32s3gpio = (struct esp32s3gpio_dev_s *)dev;
+
+  DEBUGASSERT(esp32s3gpio != NULL && value != NULL);
+  DEBUGASSERT(esp32s3gpio->id < BOARD_NGPIOIN);
+  gpioinfo("Reading... pin %" PRIu32 "\n", g_gpioinputs[esp32s3gpio->id]);
+
+  *value = esp32s3_gpioread(g_gpioinputs[esp32s3gpio->id]);
+  return OK;
+}
+#endif
+
+/****************************************************************************
+ * Name: esp32s3gpio_interrupt
+ ****************************************************************************/
+
+#if BOARD_NGPIOINT > 0
+static int esp32s3gpio_interrupt(int irq, void *context, void *arg)
+{
+  struct esp32s3gpint_dev_s *esp32s3gpint = (struct esp32s3gpint_dev_s *)arg;
+
+  DEBUGASSERT(esp32s3gpint != NULL && esp32s3gpint->callback != NULL);
+  gpioinfo("Interrupt! callback=%p\n", esp32s3gpint->callback);
+
+  esp32s3gpint->callback(&esp32s3gpint->esp32s3gpio.gpio,
+                         esp32s3gpint->esp32s3gpio.id);
+  return OK;
+}
+
+/****************************************************************************
+ * Name: gpint_read
+ ****************************************************************************/
+
+static int gpint_read(struct gpio_dev_s *dev, bool *value)
+{
+  struct esp32s3gpint_dev_s *esp32s3gpint = (struct esp32s3gpint_dev_s *)dev;
+
+  DEBUGASSERT(esp32s3gpint != NULL && value != NULL);
+  DEBUGASSERT(esp32s3gpint->esp32s3gpio.id < BOARD_NGPIOINT);
+  gpioinfo("Reading int pin...\n");
+
+  *value = esp32s3_gpioread(g_gpiointinputs[esp32s3gpint->esp32s3gpio.id]);
+  return OK;
+}
+
+/****************************************************************************
+ * Name: gpint_attach
+ ****************************************************************************/
+
+static int gpint_attach(struct gpio_dev_s *dev,
+                        pin_interrupt_t callback)
+{
+  struct esp32s3gpint_dev_s *esp32s3gpint =
+    (struct esp32s3gpint_dev_s *)dev;
+  int irq = ESP32S3_PIN2IRQ(g_gpiointinputs[esp32s3gpint->esp32s3gpio.id]);
+  int ret;
+
+  gpioinfo("Attaching the callback\n");
+
+  /* Make sure the interrupt is disabled */
+
+  esp32s3_gpioirqdisable(irq);
+  ret = irq_attach(irq,
+                   esp32s3gpio_interrupt,
+                   &g_gpint[esp32s3gpint->esp32s3gpio.id]);
+  if (ret < 0)
+    {
+      syslog(LOG_ERR, "ERROR: gpint_attach() failed: %d\n", ret);
+      return ret;
+    }
+
+  gpioinfo("Attach %p\n", callback);
+  esp32s3gpint->callback = callback;
+  return OK;
+}
+
+/****************************************************************************
+ * Name: gpint_enable
+ ****************************************************************************/
+
+static int gpint_enable(struct gpio_dev_s *dev, bool enable)
+{
+  struct esp32s3gpint_dev_s *esp32s3gpint = (struct esp32s3gpint_dev_s *)dev;
+  int irq = ESP32S3_PIN2IRQ(g_gpiointinputs[esp32s3gpint->esp32s3gpio.id]);
+
+  if (enable)
+    {
+      if (esp32s3gpint->callback != NULL)
+        {
+          gpioinfo("Enabling the interrupt\n");
+
+          /* Configure the interrupt for rising edge */
+
+          esp32s3_gpioirqenable(irq, RISING);
+        }
+    }
+  else
+    {
+      gpioinfo("Disable the interrupt\n");
+      esp32s3_gpioirqdisable(irq);
+    }
+
+  return OK;
+}
+#endif
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: esp32s3_gpio_init
+ ****************************************************************************/
+
+int esp32s3_gpio_init(void)
+{
+  int pincount = 0;
+  int i;
+
+#if BOARD_NGPIOOUT > 0
+  for (i = 0; i < BOARD_NGPIOOUT; i++)
+    {
+      /* Setup and register the GPIO pin */
+
+      g_gpout[i].gpio.gp_pintype = GPIO_OUTPUT_PIN;
+      g_gpout[i].gpio.gp_ops     = &gpout_ops;
+      g_gpout[i].id              = i;
+      gpio_pin_register(&g_gpout[i].gpio, pincount);
+
+      /* Configure the pins that will be used as output */
+
+      esp32s3_gpio_matrix_out(g_gpiooutputs[i], SIG_GPIO_OUT_IDX, 0, 0);
+      esp32s3_configgpio(g_gpiooutputs[i], OUTPUT_FUNCTION_2 |
+                         INPUT_FUNCTION_2);
+      esp32s3_gpiowrite(g_gpiooutputs[i], 0);
+
+      pincount++;
+    }
+#endif
+
+#if BOARD_NGPIOIN > 0
+  for (i = 0; i < BOARD_NGPIOIN; i++)
+    {
+      /* Setup and register the GPIO pin */
+
+      g_gpin[i].gpio.gp_pintype = GPIO_INPUT_PIN;
+      g_gpin[i].gpio.gp_ops     = &gpin_ops;
+      g_gpin[i].id              = i;
+      gpio_pin_register(&g_gpin[i].gpio, pincount);
+
+      /* Configure the pins that will be used as INPUT */
+
+      esp32s3_configgpio(g_gpioinputs[i], INPUT_FUNCTION_2);
+
+      pincount++;
+    }
+#endif
+
+#if BOARD_NGPIOINT > 0
+  for (i = 0; i < BOARD_NGPIOINT; i++)
+    {
+      /* Setup and register the GPIO pin */
+
+      g_gpint[i].esp32s3gpio.gpio.gp_pintype = GPIO_INTERRUPT_PIN;
+      g_gpint[i].esp32s3gpio.gpio.gp_ops     = &gpint_ops;
+      g_gpint[i].esp32s3gpio.id              = i;
+      gpio_pin_register(&g_gpint[i].esp32s3gpio.gpio, pincount);
+
+      /* Configure the pins that will be used as interrupt input */
+
+      esp32s3_configgpio(g_gpiointinputs[i], INPUT_FUNCTION_2 | PULLDOWN);
+
+      pincount++;
+    }
+#endif
+
+#ifdef CONFIG_ESPRESSIF_DEDICATED_GPIO
+  dedicated_gpio = esp_dedic_gpio_new_bundle(&dedic_gpio_conf);
+
+  pincount++;
+#endif
+
+  return OK;
+}
+#endif /* CONFIG_DEV_GPIO && !CONFIG_GPIO_LOWER_HALF */

boards/xtensa/esp32s3/esp32s3-8048S043/src/esp32s3_reset.c

@@ -0,0 +1,87 @@
+/****************************************************************************
+ * boards/xtensa/esp32s3/esp32s3-8048S043/src/esp32s3_reset.c
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed to the Apache Software Foundation (ASF) under one or more
+ * contributor license agreements.  See the NOTICE file distributed with
+ * this work for additional information regarding copyright ownership.  The
+ * ASF licenses this file to you under the Apache License, Version 2.0 (the
+ * "License"); you may not use this file except in compliance with the
+ * License.  You may obtain a copy of the License at
+ *
+ *   http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
+ * License for the specific language governing permissions and limitations
+ * under the License.
+ *
+ ****************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <stdlib.h>
+#include <debug.h>
+#include <assert.h>
+#include <nuttx/arch.h>
+#include <nuttx/board.h>
+
+#include "esp32s3_systemreset.h"
+
+#ifdef CONFIG_BOARDCTL_RESET
+
+#if CONFIG_BOARD_ASSERT_RESET_VALUE == EXIT_SUCCESS
+#  error "CONFIG_BOARD_ASSERT_RESET_VALUE must not be equal to EXIT_SUCCESS"
+#endif
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: board_reset
+ *
+ * Description:
+ *   Reset board.  Support for this function is required by board-level
+ *   logic if CONFIG_BOARDCTL_RESET is selected.
+ *
+ * Input Parameters:
+ *   status - Status information provided with the reset event.  This
+ *            meaning of this status information is board-specific.  If not
+ *            used by a board, the value zero may be provided in calls to
+ *            board_reset().
+ *
+ * Returned Value:
+ *   If this function returns, then it was not possible to power-off the
+ *   board due to some constraints.  The return value in this case is a
+ *   board-specific reason for the failure to shutdown.
+ *
+ ****************************************************************************/
+
+int board_reset(int status)
+{
+  syslog(LOG_INFO, "reboot status=%d\n", status);
+
+  switch (status)
+    {
+      case EXIT_SUCCESS:
+        up_shutdown_handler();
+        break;
+      case CONFIG_BOARD_ASSERT_RESET_VALUE:
+        break;
+      default:
+        break;
+    }
+
+  up_systemreset();
+
+  return 0;
+}
+
+#endif /* CONFIG_BOARDCTL_RESET */

boards/xtensa/esp32s3/esp32s3-8048S043/src/etc/init.d/rc.sysinit

@@ -0,0 +1,24 @@
+/****************************************************************************
+ * boards/xtensa/esp32s3/esp32s3-devkit/src/etc/init.d/rc.sysinit
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed to the Apache Software Foundation (ASF) under one or more
+ * contributor license agreements.  See the NOTICE file distributed with
+ * this work for additional information regarding copyright ownership.  The
+ * ASF licenses this file to you under the Apache License, Version 2.0 (the
+ * "License"); you may not use this file except in compliance with the
+ * License.  You may obtain a copy of the License at
+ *
+ *   http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
+ * License for the specific language governing permissions and limitations
+ * under the License.
+ *
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+

boards/xtensa/esp32s3/esp32s3-8048S043/src/etc/init.d/rcS

@@ -0,0 +1,31 @@
+/****************************************************************************
+ * boards/xtensa/esp32s3/esp32s3-devkit/src/etc/init.d/rcS
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed to the Apache Software Foundation (ASF) under one or more
+ * contributor license agreements.  See the NOTICE file distributed with
+ * this work for additional information regarding copyright ownership.  The
+ * ASF licenses this file to you under the Apache License, Version 2.0 (the
+ * "License"); you may not use this file except in compliance with the
+ * License.  You may obtain a copy of the License at
+ *
+ *   http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
+ * License for the specific language governing permissions and limitations
+ * under the License.
+ *
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+
+#ifdef CONFIG_SYSTEM_ADBD
+adbd &
+#endif
+
+#ifdef CONFIG_SYSTEM_FASTBOOTD
+fastbootd &
+#endif

boards/xtensa/esp32s3/esp32s3-8048S043/src/etc/txtable.txt

@@ -0,0 +1,2 @@
+TXTABLE0
+data 0x100000 0