boards/risc-v/esp32c3-generic: Add full GPIO and Buttons support

boards/risc-v/espressif/esp32h2-generic/configs/buttons/defconfig

@@ -0,0 +1,52 @@
+#
+# This file is autogenerated: PLEASE DO NOT EDIT IT.
+#
+# You can use "make menuconfig" to make any modifications to the installed .config file.
+# You can then do "make savedefconfig" to generate a new defconfig file that includes your
+# modifications.
+#
+# CONFIG_NSH_ARGCAT is not set
+# CONFIG_NSH_CMDOPT_HEXDUMP is not set
+CONFIG_ARCH="risc-v"
+CONFIG_ARCH_BOARD="esp32h2-generic"
+CONFIG_ARCH_BOARD_COMMON=y
+CONFIG_ARCH_BOARD_ESP32H2_GENERIC=y
+CONFIG_ARCH_BUTTONS=y
+CONFIG_ARCH_CHIP="espressif"
+CONFIG_ARCH_CHIP_ESPRESSIF=y
+CONFIG_ARCH_INTERRUPTSTACK=2048
+CONFIG_ARCH_IRQBUTTONS=y
+CONFIG_ARCH_RISCV=y
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_BOARDCTL_RESET=y
+CONFIG_BOARD_LOOPSPERMSEC=15000
+CONFIG_BUILTIN=y
+CONFIG_DEV_ZERO=y
+CONFIG_ESPRESSIF_ESP32H2=y
+CONFIG_ESPRESSIF_GPIO_IRQ=y
+CONFIG_EXAMPLES_BUTTONS=y
+CONFIG_FS_PROCFS=y
+CONFIG_IDLETHREAD_STACKSIZE=2048
+CONFIG_INIT_ENTRYPOINT="nsh_main"
+CONFIG_INPUT=y
+CONFIG_INPUT_BUTTONS=y
+CONFIG_INPUT_BUTTONS_LOWER=y
+CONFIG_INTELHEX_BINARY=y
+CONFIG_LIBC_PERROR_STDOUT=y
+CONFIG_LIBC_STRERROR=y
+CONFIG_NFILE_DESCRIPTORS_PER_BLOCK=6
+CONFIG_NSH_ARCHINIT=y
+CONFIG_NSH_BUILTIN_APPS=y
+CONFIG_NSH_FILEIOSIZE=512
+CONFIG_NSH_READLINE=y
+CONFIG_NSH_STRERROR=y
+CONFIG_PREALLOC_TIMERS=0
+CONFIG_RR_INTERVAL=200
+CONFIG_SCHED_BACKTRACE=y
+CONFIG_SCHED_WAITPID=y
+CONFIG_START_DAY=29
+CONFIG_START_MONTH=11
+CONFIG_START_YEAR=2019
+CONFIG_SYSTEM_DUMPSTACK=y
+CONFIG_SYSTEM_NSH=y
+CONFIG_UART0_SERIAL_CONSOLE=y

boards/risc-v/espressif/esp32h2-generic/configs/gpio/defconfig

@@ -0,0 +1,48 @@
+#
+# This file is autogenerated: PLEASE DO NOT EDIT IT.
+#
+# You can use "make menuconfig" to make any modifications to the installed .config file.
+# You can then do "make savedefconfig" to generate a new defconfig file that includes your
+# modifications.
+#
+# CONFIG_NSH_ARGCAT is not set
+# CONFIG_NSH_CMDOPT_HEXDUMP is not set
+CONFIG_ARCH="risc-v"
+CONFIG_ARCH_BOARD="esp32h2-generic"
+CONFIG_ARCH_BOARD_COMMON=y
+CONFIG_ARCH_BOARD_ESP32H2_GENERIC=y
+CONFIG_ARCH_CHIP="espressif"
+CONFIG_ARCH_CHIP_ESPRESSIF=y
+CONFIG_ARCH_INTERRUPTSTACK=2048
+CONFIG_ARCH_RISCV=y
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_BOARDCTL_RESET=y
+CONFIG_BOARD_LOOPSPERMSEC=15000
+CONFIG_BUILTIN=y
+CONFIG_DEV_GPIO=y
+CONFIG_DEV_ZERO=y
+CONFIG_ESPRESSIF_ESP32H2=y
+CONFIG_ESPRESSIF_GPIO_IRQ=y
+CONFIG_EXAMPLES_GPIO=y
+CONFIG_FS_PROCFS=y
+CONFIG_IDLETHREAD_STACKSIZE=2048
+CONFIG_INIT_ENTRYPOINT="nsh_main"
+CONFIG_INTELHEX_BINARY=y
+CONFIG_LIBC_PERROR_STDOUT=y
+CONFIG_LIBC_STRERROR=y
+CONFIG_NFILE_DESCRIPTORS_PER_BLOCK=6
+CONFIG_NSH_ARCHINIT=y
+CONFIG_NSH_BUILTIN_APPS=y
+CONFIG_NSH_FILEIOSIZE=512
+CONFIG_NSH_READLINE=y
+CONFIG_NSH_STRERROR=y
+CONFIG_PREALLOC_TIMERS=0
+CONFIG_RR_INTERVAL=200
+CONFIG_SCHED_BACKTRACE=y
+CONFIG_SCHED_WAITPID=y
+CONFIG_START_DAY=29
+CONFIG_START_MONTH=11
+CONFIG_START_YEAR=2019
+CONFIG_SYSTEM_DUMPSTACK=y
+CONFIG_SYSTEM_NSH=y
+CONFIG_UART0_SERIAL_CONSOLE=y

boards/risc-v/espressif/esp32h2-generic/include/board.h

@@ -21,5 +21,20 @@
 #ifndef __BOARDS_RISCV_ESPRESSIF_ESP32H2_GENERIC_INCLUDE_BOARD_H
 #define __BOARDS_RISCV_ESPRESSIF_ESP32H2_GENERIC_INCLUDE_BOARD_H
 
+/****************************************************************************
+ * Pre-processor Definitions
+ ****************************************************************************/
+
+/* GPIO pins used by the GPIO Subsystem */
+
+#define BOARD_NGPIOOUT    2 /* Amount of GPIO Output pins */
+#define BOARD_NGPIOINT    1 /* Amount of GPIO Input w/ Interruption pins */
+
+/* ESP32H2-Generic GPIOs ****************************************************/
+
+/* BOOT Button */
+
+#define BUTTON_BOOT  9
+
 #endif /* __BOARDS_RISCV_ESPRESSIF_ESP32H2_GENERIC_INCLUDE_BOARD_H */
 

boards/risc-v/espressif/esp32h2-generic/src/Make.defs

@@ -30,6 +30,14 @@ ifeq ($(CONFIG_BOARDCTL),y)
   endif
 endif
 
+ifeq ($(CONFIG_DEV_GPIO),y)
+  CSRCS += esp32h2_gpio.c
+endif
+
+ifeq ($(CONFIG_ARCH_BUTTONS),y)
+  CSRCS += esp32h2_buttons.c
+endif
+
 DEPPATH += --dep-path board
 VPATH += :board
 CFLAGS += ${INCDIR_PREFIX}$(TOPDIR)$(DELIM)arch$(DELIM)$(CONFIG_ARCH)$(DELIM)src$(DELIM)board$(DELIM)board

boards/risc-v/espressif/esp32h2-generic/src/esp32h2-generic.h

@@ -68,5 +68,20 @@
 
 int esp_bringup(void);
 
+/****************************************************************************
+ * Name: esp_gpio_init
+ *
+ * Description:
+ *   Configure the GPIO driver.
+ *
+ * Returned Value:
+ *   Zero (OK).
+ *
+ ****************************************************************************/
+
+#ifdef CONFIG_DEV_GPIO
+int esp_gpio_init(void);
+#endif
+
 #endif /* __ASSEMBLY__ */
 #endif /* __BOARDS_RISCV_ESPRESSIF_ESP32H2_GENERIC_SRC_ESP32H2_GENERIC_H */

boards/risc-v/espressif/esp32h2-generic/src/esp32h2_bringup.c

@@ -50,6 +50,14 @@
 #  include "esp_rtc.h"
 #endif
 
+#ifdef CONFIG_DEV_GPIO
+#  include "esp_gpio.h"
+#endif
+
+#ifdef CONFIG_INPUT_BUTTONS
+#  include <nuttx/input/buttons.h>
+#endif
+
 #include "esp32h2-generic.h"
 
 /****************************************************************************
@@ -147,6 +155,24 @@ int esp_bringup(void)
     }
 #endif
 
+#ifdef CONFIG_DEV_GPIO
+  ret = esp_gpio_init();
+  if (ret < 0)
+    {
+      ierr("Failed to initialize GPIO Driver: %d\n", ret);
+    }
+#endif
+
+#if defined(CONFIG_INPUT_BUTTONS) && defined(CONFIG_INPUT_BUTTONS_LOWER)
+  /* Register the BUTTON driver */
+
+  ret = btn_lower_initialize("/dev/buttons");
+  if (ret < 0)
+    {
+      ierr("ERROR: btn_lower_initialize() failed: %d\n", ret);
+    }
+#endif
+
   /* If we got here then perhaps not all initialization was successful, but
    * at least enough succeeded to bring-up NSH with perhaps reduced
    * capabilities.

boards/risc-v/espressif/esp32h2-generic/src/esp32h2_buttons.c

@@ -0,0 +1,198 @@
+/****************************************************************************
+ * boards/risc-v/espressif/esp32h2-generic/src/esp32h2_buttons.c
+ *
+ * Licensed to the Apache Software Foundation (ASF) under one or more
+ * contributor license agreements.  See the NOTICE file distributed with
+ * this work for additional information regarding copyright ownership.  The
+ * ASF licenses this file to you under the Apache License, Version 2.0 (the
+ * "License"); you may not use this file except in compliance with the
+ * License.  You may obtain a copy of the License at
+ *
+ *   http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
+ * License for the specific language governing permissions and limitations
+ * under the License.
+ *
+ ****************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+/* Config */
+
+#include <nuttx/config.h>
+
+/* Libc */
+
+#include <assert.h>
+#include <debug.h>
+#include <errno.h>
+#include <stdbool.h>
+#include <stdio.h>
+
+/* NuttX */
+
+#include <nuttx/arch.h>
+#include <nuttx/board.h>
+#include <nuttx/irq.h>
+#include <arch/irq.h>
+
+/* Arch */
+
+#include "esp_gpio.h"
+
+/* Board */
+
+#include "esp32h2-generic.h"
+#include <arch/board/board.h>
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: board_button_initialize
+ *
+ * Description:
+ *   board_button_initialize() must be called to initialize button resources.
+ *   After that, board_buttons() may be called to collect the current state
+ *   of all buttons or board_button_irq() may be called to register button
+ *   interrupt handlers.
+ *
+ * Input Parameters:
+ *   None.
+ *
+ * Returned Value:
+ *   The number of buttons that were initialized.
+ *
+ ****************************************************************************/
+
+uint32_t board_button_initialize(void)
+{
+  esp_configgpio(BUTTON_BOOT, INPUT_FUNCTION_3 | PULLUP);
+  return 1;
+}
+
+/****************************************************************************
+ * Name: board_buttons
+ *
+ * Description:
+ *   After board_button_initialize() has been called, board_buttons() may be
+ *   called to collect the state of all buttons.
+ *
+ * Input Parameters:
+ *   None.
+ *
+ * Returned Value:
+ *   An 8-bit bit set with each bit associated with a button. See the
+ *   BUTTON_*_BIT definitions in board.h for the meaning of each bit.
+ *
+ ****************************************************************************/
+
+uint32_t board_buttons(void)
+{
+  uint8_t ret = 0;
+  int i = 0;
+  int n = 0;
+
+  bool b0 = esp_gpioread(BUTTON_BOOT);
+
+  for (i = 0; i < 10; i++)
+    {
+      up_mdelay(1); /* TODO */
+
+      bool b1 = esp_gpioread(BUTTON_BOOT);
+
+      if (b0 == b1)
+        {
+          n++;
+        }
+      else
+        {
+          n = 0;
+        }
+
+      if (3 == n)
+        {
+          break;
+        }
+
+      b0 = b1;
+    }
+
+  iinfo("b=%d n=%d\n", b0, n);
+
+  /* Low value means that the button is pressed */
+
+  if (!b0)
+    {
+      ret = 0x1;
+    }
+
+  return ret;
+}
+
+/****************************************************************************
+ * Name: board_button_irq
+ *
+ * Description:
+ *   board_button_irq() may be called to register an interrupt handler that
+ *   will be called when a button is depressed or released. The ID value is
+ *   a button enumeration value that uniquely identifies a button resource.
+ *   See the BUTTON_* definitions in board.h for the meaning of enumeration
+ *   value.
+ *
+ * Input Parameters:
+ *   id         - Identifies the button to be monitored. It is equivalent to
+ *                the bit used to report the button state in the return value
+ *                from board_buttons().
+ *   irqhandler - The handler that will be invoked when the interrupt occurs.
+ *   arg        - Pointer to the arguments that will be provided to the
+ *                interrupt handler.
+ *
+ * Returned Value:
+ *   Zero (OK) on success; a negated errno value on failure.
+ *
+ ****************************************************************************/
+
+#ifdef CONFIG_ARCH_IRQBUTTONS
+int board_button_irq(int id, xcpt_t irqhandler, void *arg)
+{
+  int ret;
+  DEBUGASSERT(id == 0);
+
+  int irq = ESP_PIN2IRQ(BUTTON_BOOT);
+
+  if (NULL != irqhandler)
+    {
+      /* Make sure the interrupt is disabled */
+
+      esp_gpioirqdisable(irq);
+
+      gpioinfo("Attach %p\n", irqhandler);
+
+      ret = irq_attach(irq, irqhandler, arg);
+      if (ret < 0)
+        {
+          syslog(LOG_ERR, "ERROR: irq_attach() failed: %d\n", ret);
+          return ret;
+        }
+
+      /* Configure the interrupt for rising and falling edges */
+
+      gpioinfo("Enabling the interrupt\n");
+      esp_gpioirqenable(irq, CHANGE);
+    }
+  else
+    {
+      gpioinfo("Disable the interrupt\n");
+      esp_gpioirqdisable(irq);
+    }
+
+  return OK;
+}
+#endif