[new] Altered the way default settings are stored and restored. Saved about 300 bytes(!) of flashed size. Should free up enough for certain configurations of CoreXY machines.
[fix] When the optional M7 mist coolant IO was enabled, coolant overrides was not disabling correctly.
[fix] Coolant override states was not restored correctly after a parking motion in certain situations. It would restore programmed state, rather than current overridden state.
[fix] Now allow coolant overrides to operate during jogging motion.
[fix] Invert control pin mask typo.
[new] Added a new build info feedback mechanism for enabling the safety door input pin.
[fix] RAMPS soft-reset control pin interfered with Z-enable. Shifted
all control pins by plus one on the analog pins. RAMPS defines these
pins as belonging to the AUX 2 port, which is assumed to be unused.
- [fix] Spindle enable pin behavior corrected to be independent of the
PWM output. There was some crossover behavior.
- [fix] Tool numbers are now tracking and reporting correctly.
- [fix] G-code parser error when G0 is commanded without a feed rate
word while in inverse time mode.
- [fix] Config file was missing an option for probing behavior.
- [doc] Updated documentation.
- Applied an alarm handling bug fix that would not show the correct
alarm code, nor clear the alarm. It would occasionally go into an
infinite loop and would usually happen during a homing cycle fail.
- v1.1e
- Ported all current changes from the main Grbl 328p repo to the
Mega2560 branch. Main differences are increased planner, RX, TX, and
line buffers. And an optional sleep timeout feature.
- WARNING: Code compiles, but has not been tested.
- Removed all of the 328p-related code, which seemed to clean up things
quite a bit without all those ifdefs everywhere.
- Since the 328p was very memory and flash limited, lots of
compile-time options were disabled by default. These have been now been
enabled by default. As they are considered generally helpful and does
not significantly impact how Grbl runs.
- For example, status reports can now report back real time feed rate
and line number being executed. Variable spindle is standard with a
separate spindle enable pin. Grbl will now check if a user setting has
exceeded the maximum step frequency and report an error, if so. And
finally, M7 flood coolant is enabled.
- In addition, all buffers have been significantly increased to take
advantage of the additional memory available. The planner buffer can
plan up to 36 motions. The serial buffers have been doubled in size
(256/128 bytes RX/TX). And the longest line Grbl can accept is 256
bytes, per the g-code standard (Grbl 328p is limited to 80).
- Removed the cpu_map folder, since this version is strictly Mega2560.
- Soft limit errors were stuck in a feed hold without notifying the
user why it was in a hold. When resumed, the soft limit error would
kick in. Issue should be fixed to behave as intended. To automatically
hold and issue a soft limit alarm once the machine has come to a stop.
- Planner was under-estimating maximum speeds through straight
junctions in certain cases. The calculations have been updated to be
more accurate.
- Strange sizeof() bug in the most recent releases. Manifested as an
alarm upon a power up even when homing was disabled. Fixed by declaring
sizeof() with struct types, rather than variable names, even though
they were validated to give the same value.
- Spindle speed zero should disable the spindle. Now fixed.
- New configuration option for inverting certain limit pins. Handy for
mixed NO and NC switch machines. See config.h for details.
- New pin state realtime reporting feature. Instead of `Lim:000` for
limit state reports, the new feature shows `Pin:000|0|0000`, or
something similar. The `|` delimited fields indicate xyz limits, probe,
and control pin states, where 0 is always not triggered, and 1 is
triggered. Invert masks ARE accounted for.
Each field may be enabled or disabled via the `$10` status report
setting. The probe and control pin flags are bits 5 and 6, respectively.
- Remove the now deprecated `REPORT_CONTROL_PIN_STATE` option in
config.h
- The old limit pin reports `Lim:000` may be re-enabled by commenting
out `REPORT_ALL_PIN_STATES` in config.h.
- Incremented the version letter (v1.0c) to indicate the change in
reporting style.
- Replaced all bit_true_atomic and bit_false_atomic macros with
function calls. This saved a couple hundred bytes of flash.
- G38.x was not printing correctly in the $G g-code state reports. Now
fixed.
- When investigating the above issue, it was noticed that G38.x
wouldn’t show at all, but instead a G0 would be printed. This was
unlike the v0.9j master build. It turned out volatile variables do not
like to be defined inside a C struct. These are undefined on how to be
handled. Once pulled out, all weird issues went away.
- Also changed two ‘sizeof()’ statements in the mc_probe() and
probe_state_monitor() functions to be more robust later on.
- Updated the commit logs to individual files for each minor release.
Forgot to update the generating script to account for this.
- G38.x was not printing correctly in the $G g-code state reports. Now
fixed.
- Potential bug regarding volatile variables inside a struct. It has
never been a problem in v0.9, but ran into this during v1.0
development. Just to be safe, the fixes are applied here.
- Updated pre-built firmwares with these two bug fixes.
- G28 and G30’s behavior has been updated from the old NIST g-code
standard to LinuxCNC’s. Previously when an intermediate motion was
programmed, the NIST standard would move all axes to the final G28/30
stored coordinates. LinuxCNC states it only moves the axes specified in
the command.
For example, suppose G28’s stored position is (x,y,z) = (1,2,3) for
simplicity, and we want to do an automated z-axis tool retraction and
then park at the x,y location. `G28 G91 Z5` will first move the Z axis
5mm(or inches) up, then move Z to position 3 in machine coordinates.
Next, the command `G28 G91 X0 Y0` would skip the intermediate move
since distance is zero, but then move only the x and y axes to machine
coordinates 1 and 2, respectively. The z-axis wouldn’t move in this
case, since it wasn’t specified.
This change is intended to make Grbl more LinuxCNC compatible while
making commands, like the shown tool retraction, much easier to
implement.
- Tons of new stuff in this release, which is fairly stable and well
tested. However, much more is coming soon!
- Real-time parking motion with safety door. When this compile option
is enabled, an opened safety door will cause Grbl to automatically feed
hold, retract, de-energize the spindle/coolant, and parks near Z max.
After the door is closed and resume is commanded, this reverses and the
program continues as if nothing happened. This is also highly
configurable. See config.h for details.
- New spindle max and min rpm ‘$’ settings! This has been requested
often. Grbl will output 5V when commanded to turn on the spindle at its
max rpm, and 0.02V with min rpm. The voltage and the rpm range are
linear to each other. This should help users tweak their settings to
get close to true rpm’s.
- If the new max rpm ‘$’ setting is set = 0 or less than min rpm, the
spindle speed PWM pin will act like a regular on/off spindle enable
pin. On pin D11.
- BEWARE: Your old EEPROM settings will be wiped! The new spindle rpm
settings require a new settings version, so Grbl will automatically
wipe and restore the EEPROM with the new defaults.
- Control pin can now be inverted individually with a
CONTROL_INVERT_MASK in the cpu_map header file. Not typical for users
to need this, but handy to have.
- Fixed bug when Grbl receive too many characters in a line and
overflows. Previously it would respond with an error per overflow
character and another acknowledge upon an EOL character. This broke the
streaming protocol. Now fixed to only respond with an error after an
EOL character.
- Fixed a bug with the safety door during an ALARM mode. You now can’t
home or unlock the axes until the safety door has been closed. This is
for safety reasons (obviously.)
- Tweaked some the Mega2560 cpu_map settings . Increased segment buffer
size and fixed the spindle PWM settings to output at a higher PWM
frequency.
- Generalized the delay function used by G4 delay for use by parking
motion. Allows non-blocking status reports and real-time control during
re-energizing of the spindle and coolant.
- Added spindle rpm max and min defaults to default.h files.
- Added a new print float for rpm values.
- Version bump requested by OEMs to easily determine whether the
firmware supports the new EEPROM reset feature. Other than that, no
significant changes.
- Tweaked the previous EEPROM restore implementation and added new
functionality.
- `$RST=$` restores the `$$` grbl settings back to firmware defaults,
which are set when compiled.
- `$RST=#` restores the `$#` parameters in EEPROM. At times it’s useful
to clear these and start over, rather than manually writing each entry.
-`$RST=*` wipe all of the data in EEPROM that Grbl uses and restores
them to defaults. This includes `$$` settings, `$#` parameters, `$N`
startup lines, and `$i` build info string.
NOTE: This doesn’t write zeros throughout the EEPROM. It only writes
where Grbl looks for data. For a complete wipe, please use the Arduino
IDE’s EEPROM clear example.
- Refactored the restore and wipe functions in settings.c to
accommodate the new commands.
- New restore setting defaults command. Only wipes ‘$$’ setting in
EEPROM and reloads them based on the defaults used when Grbl was
compiled. Used with a `$RST` command
NOTE: `$RST` is intentionally not listed in the Grbl ‘$’ help message.
- Added X-Carve 500mm and 1000mm default files.
- Tweaked all default files. Removed obsolete AUTO_START and updated
some JUNCTION_DEVIATION defaults after testing showed these needed to
be reduced slightly.
- Updated new homing cycle to error out when a pull-off motion detects
the limit is still active.
- Created a limits_get_state() function to centralize it. It reports
state as a bit-wise booleans according to axis numbering.
- Updated the print uint8 functions. Generalized it to allow both base2
and base10 printouts, while allowing base2 prints with N_AXIS digits
for limit state status reports. Doing this saved about 100bytes of
flash as well.
- Applied CoreXY status reporting bug fix by @phd0. Thanks!
- Critical fix for M0 program pause. Due to its recent change, it would
cause Grbl to suspend but wouldn’t notify the user of why Grbl was not
doing anything. The state would show IDLE and a cycle start would
resume it. Grbl now enters a HOLD state to better indicate the state
change.
- Critical fix for M2 and M30 program end. As with M0, the state
previously would show IDLE while suspended. Grbl now does not suspend
upon program end and leaves job control to the GUI. Grbl simply reports
a `[Pgm End]` as a feedback message and resets certain g-code modes.
- M2/30 g-code reseting fix. Previously Grbl would soft-reset after an
M2/30, but this was not complaint to the (linuxcnc) g-code standard. It
simply resets [G1,G17,G90,G94,G40,G54,M5,M9,M48] and keeps all other
modes the same.
- M0/M2/M30 check-mode fix. It now does not suspend the machine during
check-mode.
- Minor bug fix related to commands similar to G90.1, but not G90.1,
not reporting an unsupported command.
- Homing cycle refactoring. To help reduce the chance of users
misunderstanding their limit switch wiring, Grbl only moves a short
distance for the locate cycles only. In addition, the homing cycle
pulls-off the limit switch by the pull-off distance to re-engage and
locate home. This should improve its accuracy.
- HOMING_FORCE_ORIGIN now sets the origin to the pull-off location,
rather than where the limit switch was triggered.
- Updated default junction deviation to 0.01mm. Recent tests showed
that this improves Grbl’s cornering behavior a bit.
- Added the ShapeOko3 defaults.
- Added new feedback message `[Pgm End]` for M2/30 notification.
- Limit pin reporting is now a $10 status report option. Requested by
OEMs to help simplify support troubleshooting.
- Commit history added to repo, as an easier way for people to see view
the changes over time.
- Grbl logo copyright license added. All rights reserved with regards
to the Grbl logo.
- G2/3 full circles would sometime not execute. The problem was due to
numerical round-off of a trig calculation. Added a machine epsilon
define to help detect and correct for this problem. Tested and should
not effect general operation of arcs.
- The homing cycle should be working again. Reverted it back to how it
was about a month ago before I started to fiddle with it. Turns out
that my past self knew what he was doing.
- Added an include in the right spot, if a user tries to compile and
upload Grbl through the Arduino IDE with the old way.
- Fixed a minor bug with homing max travel calculations. It was causing
simultaneous axes homing to move slow than it did before.
- G91.1 support added. This g-code sets the arc IJK distance mode to
incremental, which is the default already. This simply helps reduce
parsing errors with certain CAM programs that output this command.
- Max step rate checks weren’t being compiled in if the option was
enabled. Fixed now.
- Alarm codes were not displaying correctly when GUI reporting mode was
enabled. Due to unsigned int problem. Changed codes to positive values
since they aren’t shared with other codes.
- New configuration option at compile-time:
- Force alarm upon power-up or hard reset. When homing is enabled,
this is already the default behavior. This simply forces this all of
the time.
- GUI reporting mode. Removes most human-readable strings that GUIs
don’t need. This saves nearly 2KB in flash space that can be used for
other features.
- Hard limit force state check: In the hard limit pin change ISR, Grbl
by default sets the hard limit alarm upon any pin change to guarantee
the alarm is set. If this option is set, it’ll check the state within
the ISR, but can’t guarantee the pin will be read correctly if the
switch is bouncing. This option makes hard limit behavior a little less
annoying if you have a good buffered switch circuit that removes
bouncing and electronic noise.
- Software debounce bug fix. It was reading the pin incorrectly for the
setting.
- Re-factored some of the ‘$’ settings code.
- Instead of a single overall max travel for a search distance for the
homing limit switches. The homing cycle now applies the max travel of
each axis to the search target. Generally makes more sense this way and
saved more than a 100bytes of flash too.
- Homing cycle failure reports alarm feedback when the homing cycle is
exited via a reset, interrupted by a safety door switch, or does not
find the limit switch.
- Homing cycle bug fix when not finding the limit switch. It would just
idle before, but now will exit with an alarm.
- Licensing update. Corrected licensing according to lawyer
recommendations. Removed references to other Grbl versions.
- Overhauled the state machine and cleaned up its overall operation.
This involved creating a new ‘suspend’ state for what all external
commands, except real-time commands, are ignored. All hold type states
enter this suspend state.
- Removed ‘auto cycle start’ setting from Grbl. This was not used by
users in its intended way and is somewhat redundant, as GUI manage the
cycle start by streaming. It also muddled up how Grbl should interpret
how and when to execute a g-code block. Removing it made everything
much much simpler.
- Fixed a program pause bug when used with other buffer_sync commands.
- New safety door feature for OEMs. Immediately forces a feed hold and
then de-energizes the machine. Resuming is blocked until the door is
closed. When it is, it re-energizes the system and then resumes on the
normal toolpath.
- Safety door input pin is optional and uses the feed hold pin on A1.
Enabled by config.h define.
- Spindle and coolant re-energizing upon a safety door resume has a
programmable delay time to allow for complete spin up to rpm and
turning on the coolant before resuming motion.
- Safety door-style feed holds can be used instead of regular feed hold
(doesn’t de-energize the machine) with a ‘@‘ character. If the safety
door input pin is not enabled, the system can be resumed at any time.
- ‘build’ directory was not being synced by git because it was empty.
Added a .gitignore file in the ‘build’ directory to force git to sync
it but keep it empty.
- Updated the Makefile to not erase the .gitignore.
- Re-organized source code files into a ‘grbl’ directory to lessen one
step in compiling Grbl through the Arduino IDE.
- Added an ‘examples’ directory with an upload .INO sketch to further
simplify compiling and uploading Grbl via the Arduino IDE.
- Updated the Makefile with regard to the source code no longer being
in the root directory. All files generated by compiling is placed in a
separate ‘build’ directory to keep things tidy. The makefile should
operate in the same way as it did before.
- Critical bug fix for diagonal motions that continue on the same
direction or return in the exact opposite direction. This issue could
cause Grbl to crash intermittently due to a numerical round-off error.
Grbl versions prior to v0.9g shouldn’t have this issue.
- Reorganized all of the includes used by Grbl. Centralized it into a
single “grbl.h” include. This will help simplify the compiling and
uploading process through the Arduino IDE.
- Added an example .INO file for users to simply open and run when
compiling and uploading through the IDE. More to come later.
- As a setup feature, users can compile-in input pin status reporting.
Doesn’t do anything special, just prints the binary for the port. 0’s
and 1’s indicate low and high signals on the pins. It’s a bit cryptic
right now, but it’s just a start.
- Added a max step rate check when writing step/mm and max rate
settings. Should help avoid people misdiagnosing problems associated
with going over the 30kHz step rate limit. Right now not enabled. Takes
up over 100k of flash. Need that room for other things right now.
- Planner bug when moving along a diagonal back and forth on the same
path. Rare for the fact that most CAM programs don’t program this type
of motion, neither does jogging. Fixed in this update.
- Added grbl_sim defaults for testing purposes.
- All pins, which include limits, control command, and probe pins, can
now all be configured to trigger as active-low or active-high and
whether the pin has its internal pull-up resistor enabled. This should
allow for just about all types of NO and NC switch configurations.
- The probe pin invert setting hasn’t been added to the Grbl settings,
like the others, and will have to wait until v1.0. But for now, it’s
available as a compile-time option in config.h.
- Fixed a variable spindle bug.
- Rudimentary CoreXY kinematics support. Didn’t test, but homing and
feed holds should work. See config.h. Please report successes and
issues as we find bugs.
- G40 (disable cutter comp) is now “supported”. Meaning that Grbl will
no longer issue an error when typically sent in g-code program header.
- Refactored coolant and spindle state setting into separate functions
for future features.
- Configuration option for fixing homing behavior when there are two
limit switches on the same axis sharing an input pin.
- Created a new “grbl.h” that will eventually be used as the main
include file for Grbl. Also will help simply uploading through the
Arduino IDE
- Separated out the alarms execution flags from the realtime (used be
called runtime) execution flag variable. Now reports exactly what
caused the alarm. Expandable for new alarms later on.
- Refactored the homing cycle to support CoreXY.
- Applied @EliteEng updates to Mega2560 support. Some pins were
reconfigured.
- Created a central step to position and vice versa function. Needed
for non-traditional cartesian machines. Should make it easier later.
- Removed the new CPU map for the Uno. No longer going to used. There
will be only one configuration to keep things uniform.
- Minor bug fix for variable spindle PWM output. Values smaller than
the minimum RPM for the spindle would overflow the PWM value. Thanks
Rob!
- Created an optional minimum spindle PWM low-mark value as a
compile-time option. This is for special circumstances when the PWM has
to be at a certain level to be read by the spindle controller.
- Refactored the new probing commands (G38.3, G38.4, G38.5) code to
work better with the rest of Grbl’s systems.
- Refactored mc_probe() and mc_arc() to accept the mode of the command,
i.e. clockwise vs counter, toward vs away, etc. This is to make these
functions independent of gcode state variables.
- Removed the pull off motion in the probing cycle. This is not an
official operation and was added for user simplicity, but wrongly did
so. So bye bye.
- Created a configure probe invert mask function to handle the
different probe pin setting and probing cycle modes with a single mask.
- Minor bug fix with reporting motion modes via $G. G38.2 wasn’t
showing up. It now does, along with the other new probing commands.
- Refactored some of the new pin configurations for the future of Grbl.
-
- The `x` in `$x=val` would overflow when a value larger than 255 was
entered and passed to Grbl. This resulted with unintended parameters
being set by the overflow value. To fix, simply check for values larger
than 255 and error out.
- Sometime I HATE github. This push is just here to be able to describe
the last two pushes today that had a merging conflict and lost all of
the commit comments before.
- Setting $10 would cause $11 to be the same value. Missed a break
statement in the switch-case. Oops! Now fixed.
- CPU pin map for the future versions of Grbl introduced, but not yet
finalized. Still working on it and it’s subject to change.
- Added a new high-speed machining test g-code routine written by Todd
Fleming. Mills a pocket at 15,000mm/min. Do not use when connected to
your machine! You’ve been warned!
- Updated ShapeOko2 defaults based on machine testing of the basic
model provided by Inventables. (or close to it.) Should be pretty
conservative but much faster than before. For example, X and Y axes are
set at (10x) faster at 5000mm/min. It can run much faster than this,
but this seems like a safe speed for everyone.
- Updated README for master release.
- Added some new settings methods for clearing the EEPROM when changing
versions. Needs some more work, but it should ok for master release.
Should work on it more for the next version.
- When updating from v0.8, the settings will wipe the startup lines and
build info locations so that it won’t use whatever is already there in
the EEPROM. Parameters (coord offsets) are retained. They should be ok
during an upgrade.
- A G28/30 bug would cause it to move to machine coordinate [0,0,0] if
no axis words were sent. It was a typo in the new g-code parser. Fixed
and slightly re-written to be more consistent with the program flow.
- Updated the ShapeOko2 defaults based on testing on the real machine.
A little conservative, but it might change again after some more
testing.
- Now blocks ‘$$’ command during a motion, because the printout takes
too long and can starve the segment buffer.
- A very very low feed rate command like `G1 X100 F0.01` would cause
some floating-point round-off error and freeze Grbl into an infinite
loop. To fix it, introduced a MINIMUM_FEED_RATE parameter in config.h
to ensure motions always complete.
- MINIMUM_FEED_RATE is set at 1.0 mm/min by default. It’s recommended
that no rates are below this value, but 0.1mm/min may be ok in some
situations.
- Restored probe position syncing. Had removed a pull-off motion after
a probe cycle completes, but ended up de-synchronizing the g-code
parser and probing cycle positions. Putting the pull-off motion back
fixed the problem.
- Probing cycle would drop into a QUEUED state, if multiple G38.2 are
sent. It would not honor the auto cycle start flags. To fix, the auto
cycle start state is saved at the beginning of the probing cycle and
restored at the end, since the feed hold it uses to stop a triggered
probe will disable the auto start flag. For now it’s a patch, rather
than a permanent fix.
- protocol_buffer_synchronize() also has a failure case. Auto cycle
start does not get executed when the system is waiting in here, so if
it’s in a QUEUED state already, it won’t resume. Patched here, but not
fully resolved.
- Fixed a problem with the “view build info” command. The EEPROM write
would do weird things and corrupt the EEPROM. Not sure exactly what
caused it, but it’s likely a compiler problem with an improperly
defined EEPROM address. It didn’t have enough room to store a full
string. To fix, the build info EEPROM range was increased and the max
number of STARTUP_BLOCKS was reduced to 2 from 3.
- Lastly, when a $I view build info is used for the first time, it
would normally show an EEPROM read error, since it wasn’t cleared or
wasn’t therein the first place. It will now not show that error. A
patch rather than a permanent fix again.
- Bug fix for step and direction invert masks not immediately being in
effect. Now regenerates the masks when a user changes this setting.
- Bug fix for probing cycle. G-code standard mandates that there is an
error if the probe is already triggered when the cycle is commanded.
However, Grbl may have motions to pull off a previous probing cycle in
queue and can falsely lead to errors. To fix this, the triggered check
is performed within the probing cycle itself, right after the planner
buffer is synced. If there is an error, it will now alarm out as a
probe fail.
- `$I` prints the Grbl build info and version number. NOTE: `$I=xxx`
stores an additional 30 character string into EEPROM, which will be
printed with the build info the next time it’s run. This is for
identification purposes for users that have more than one system using
Grbl.
- Only minor changes were required to make the Arduino IDE compile all
of the Grbl’s source code (correctly using the C-compiler). Tested in
Windows and Mac and with the normal USB upload and with a programmer.
This is likely the last major change to the v0.9 code base before push
to master. Only two minor things remain on the agenda (CoreXY support,
force clear EEPROM, and an extremely low federate bug).
- NEW! Grbl is now compile-able and may be flashed directly through the
Arduino IDE. Only minor changes were required for this compatibility.
See the Wiki to learn how to do it.
- New status reporting mask to turn on and off what Grbl sends back.
This includes machine coordinates, work coordinates, serial RX buffer
usage, and planner buffer usage. Expandable to more information on user
request, but that’s it for now.
- Settings have been completely renumbered to allow for future new
settings to be installed without having to constantly reshuffle and
renumber all of the settings every time.
- All settings masks have been standardized to mean bit 0 = X, bit 1 =
Y, and bit 2 = Z, to reduce confusion on how they work. The invert
masks used by the internal Grbl system were updated to accommodate this
change as well.
- New invert probe pin setting, which does what it sounds like.
- Fixed a probing cycle bug, where it would freeze intermittently, and
removed some redundant code.
- Homing may now be set to the origin wherever the limit switches are.
Traditionally machine coordinates should always be in negative space,
but when limit switches on are on the opposite side, the machine
coordinate would be set to -max_travel for the axis. Now you can always
make it [0,0,0] via a compile-time option in config.h. (Soft limits
routine was updated to account for this as well.)
- Probe coordinate message immediately after a probing cycle may now
be turned off via a compile-time option in config.h. By default the
probing location is always reported.
- Reduced the N_ARC_CORRECTION default value to reflect the changes in
how circles are generated by an arc tolerance, rather than a fixed arc
segment setting.
- Increased the incoming line buffer limit from 70 to 80 characters.
Had some extra memory space to invest into this.
- Fixed a bug where tool number T was not being tracked and reported
correctly.
- Added a print free memory function for debugging purposes. Not used
otherwise.
- Realtime rate report should now work during feed holds, but it hasn’t
been tested yet.
- Updated the streaming scripts with MIT-license and added the simple
streaming to the main stream.py script to allow for settings to be sent.
- Some minor code refactoring to improve flash efficiency. Reduced the
flash by several hundred KB, which was re-invested in some of these new
features.
- Incremented from v0.9e to v0.9f due to the new g-codes, velocity
reporting option, decimal printing refactoring, grbl-sim updates, and
G0/G1 bug fix.
- Settings version was also incremented since settings.decimal_places
is now gone.
Sonny Jeon