airframes: add r1 again

This was dropped in f454dcef6b

ROMFS/px4fmu_common/init.d/airframes/50003_aion_robotics_r1_rover

@@ -0,0 +1,75 @@
+#!/bin/sh
+#
+# @name Aion Robotics R1 UGV
+#
+# @url https://www.aionrobotics.com/r1
+#
+# @type Rover
+# @class Rover
+#
+# @board px4_fmu-v2 exclude
+# @board bitcraze_crazyflie exclude
+#
+
+. ${R}etc/init.d/rc.rover_defaults
+
+param set-default BAT1_N_CELLS 4
+
+param set-default EKF2_GBIAS_INIT 0.01
+param set-default EKF2_ANGERR_INIT 0.01
+param set-default EKF2_MAG_TYPE 1
+
+param set-default FW_AIRSPD_MIN 0
+param set-default FW_AIRSPD_TRIM 1
+param set-default FW_AIRSPD_MAX 3
+
+param set-default GND_SP_CTRL_MODE 1
+param set-default GND_L1_DIST 5
+param set-default GND_L1_PERIOD 3
+param set-default GND_THR_CRUISE 0.7
+param set-default GND_THR_MAX 0.5
+
+# Because this is differential drive, it can make a turn with radius 0.
+# This corresponds to a turn angle of pi radians.
+# If a special case is made for differential-drive, this will need to change.
+param set-default GND_MAX_ANG 3.142
+param set-default GND_WHEEL_BASE 0.3
+
+# TODO: Set to -1.0, to allow reversing. This will require many changes in the codebase
+# to support negative throttle.
+param set-default GND_THR_MIN 0
+param set-default GND_SPEED_P 0.25
+param set-default GND_SPEED_I 3
+param set-default GND_SPEED_D 0.001
+param set-default GND_SPEED_IMAX 0.125
+param set-default GND_SPEED_THR_SC 1
+
+param set-default MIS_LTRMIN_ALT 0.01
+param set-default MIS_TAKEOFF_ALT 0.01
+
+param set-default NAV_ACC_RAD 0.5
+
+# Enable Airspeed check circuit breaker because Rovers will have no airspeed sensor
+param set-default CBRK_AIRSPD_CHK 162128
+
+# Differential drive acts like ackermann steering with a maximum turn angle of 180 degrees, or pi radians
+param set-default GND_MAX_ANG 3.1415
+
+param set-default RBCLW_BAUD 8
+param set-default RBCLW_COUNTS_REV 1200
+param set-default RBCLW_ADDRESS 128
+# 104 corresponds to Telem 4
+param set-default RBCLW_SER_CFG 104
+# Start this driver after setting parameters, because the driver uses some of those parameters.
+# roboclaw start /dev/ttyS3
+
+# Set geometry & output configration
+param set-default CA_AIRFRAME 6
+param set-default CA_R_REV 3
+param set-default PWM_MAIN_FUNC1 101
+param set-default PWM_MAIN_FUNC2 102
+param set-default PWM_MAIN_DIS1 1500
+param set-default PWM_MAIN_DIS2 1500
+param set-default PWM_MAIN_TIM0 50
+param set-default PWM_MAIN_TIM1 50
+

ROMFS/px4fmu_common/init.d/airframes/CMakeLists.txt

@@ -118,6 +118,7 @@ px4_add_romfs_files(
 
 	50000_generic_ground_vehicle
 	50004_nxpcup_car_dfrobot_gpx
+	50003_aion_robotics_r1_rover
 
 	# [60000, 61000] (Unmanned) Underwater Robots
 	60000_uuv_generic