Mirrors_Framework/PX4-Autopilot
1
0
Fork 0
mirror of https://github.com/PX4/PX4-Autopilot.git synced 2026-05-27 18:27:05 +08:00
Code Issues Actions 30 Packages Projects Releases Wiki Activity

New Crowdin translations - zh-CN (#24829)

Browse Source 
Co-authored-by: Crowdin Bot <support+bot@crowdin.com>
This commit is contained in:
PX4 Build Bot
2025-05-14 09:22:33 +10:00
committed by GitHub
parent 2b7710122e
commit 8adb439b58
14 changed files with 366 additions and 215 deletions
Download Patch File Download Diff File Expand all files Collapse all files
docs/zh/flight_controller/kakuteh7-wing.md
+84
View File
@@ -0,0 +1,84 @@
# Holybro Kakute H7 V2
:::warning
PX4 does not manufacture this (or any) autopilot.
Contact the [manufacturer](https://holybro.com/) for hardware support or compliance issues.
:::
The [Holybro Kakute H743 Wing](https://holybro.com/products/kakute-h743-wing) is a fully featured flight controller specifically aimed at fixed-wing and VTOL applications. It has the STM32 H743 Processor running at 480 MHz and CAN Bus support, along with dual camera support & switch, ON/OFF Pit Switch, 5V, 6V/8V, 9V/12 BEC, and plug-and-play GPS, CAN, I2C ports.
:::info
This flight controller is [manufacturer supported](../flight_controller/autopilot_manufacturer_supported.md).
:::
## 购买渠道
The board can be bought from one of the following shops (for example):
- [Holybro](https://holybro.com/products/kakute-h743-wing)
## Connectors and Pins
| 针脚 | 功能 | PX4 default |
| ---------------- | --------------------------------- | ------------------------------------------------------------- |
| GPS 1 | USART1 and I2C1 | GPS1 |
| R2, T2 | USART2 RX and TX | GPS2 |
| R3, T3 | USART3 RX and TX | TELEM1 |
| R5, T5 | USART5 RX and TX | TELEM2 |
| R6, T6 | USART6 RX and TX | RC (PPM, SBUS, etc.) input |
| R7, T7, RTS, CTS | UART7 RX and TX with flow control | TELEM3 |
| R8, T8 | UART8 RX and TX | Console |
| Buz-, Buz+ | Piezo buzzer | |
| M1 to M14 | Motor signal outputs | |
<a id="bootloader"></a>
## PX4 Bootloader Update
The board comes pre-installed with [Betaflight](https://github.com/betaflight/betaflight/wiki).
Before the PX4 firmware can be installed, the _PX4 bootloader_ must be flashed.
Download the [holybro_kakuteh7-wing.hex](https://github.com/PX4/PX4-Autopilot/raw/main/docs/assets/flight_controller/kakuteh7-wing/holybro_kakuteh7-wing_bootloader.hex) bootloader binary and read [this page](../advanced_config/bootloader_update_from_betaflight.md) for flashing instructions.
## 编译固件
To [build PX4](../dev_setup/building_px4.md) for this target:
```
make holybro_kakuteh7-wing_default
```
## Installing PX4 Firmware
:::info
KakuteH7-wing is supported with PX4 master & PX4 v1.16 or newer..
Prior to that release you will need to manually build and install the firmware.
:::
Firmware can be manually installed in any of the normal ways:
- Build and upload the source:
```
make holybro_kakuteh7-wing_default upload
```
- [Load the firmware](../config/firmware.md) using _QGroundControl_.
You can use either pre-built firmware or your own custom firmware.
## 串口映射
| UART | 设备 | Port | Default function |
| ------ | ---------- | --------------------------- | ---------------- |
| USART1 | /dev/ttyS0 | GPS 1 | GPS1 |
| USART2 | /dev/ttyS1 | R2, T2 | GPS2 |
| USART3 | /dev/ttyS2 | R3, T3 | TELEM1 |
| UART5 | /dev/ttyS3 | R5, T5 | TELEM2 |
| USART6 | /dev/ttyS4 | R6, (T6) | 遥控输入 |
| UART7 | /dev/ttyS5 | R7, T7, RTS, CTS | TELEM3 |
| UART8 | /dev/ttyS6 | R8, T8 | Console |
## 调试接口
### 系统控制台
UART8 RX and TX are configured for use as the [System Console](../debug/system_console.md).