nuttx/boards/arm/stm32f0l0g0/b-l072z-lrwan1/include/board.h

/****************************************************************************
 * boards/b-l072z-lrwan1/include/board.h
 * include/arch/board/board.h
 *
 *   Copyright (C) 2018 Gregory Nutt. All rights reserved.
 *   Author: Mateusz Szafoni <raiden00@railab.me>
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in
 *    the documentation and/or other materials provided with the
 *    distribution.
 * 3. Neither the name NuttX nor the names of its contributors may be
 *    used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
 * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
 * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
 * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
 * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
 * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 *
 ****************************************************************************/

#ifndef __BOARDS_ARM_B_L072Z_LRWAN1_INCLUDE_BOARD_H
#define __BOARDS_ARM_B_L072Z_LRWAN1_INCLUDE_BOARD_H

/****************************************************************************
 * Included Files
 ****************************************************************************/

#include <nuttx/config.h>

#ifndef __ASSEMBLY__
#  include <stdint.h>
#  include <stdbool.h>
#endif

/****************************************************************************
 * Pre-processor Definitions
 ****************************************************************************/

/* Clocking *****************************************************************/

/* HSI - Internal 16 MHz RC Oscillator
 * LSI - 32 KHz RC
 * HSE - 8 MHz from MCO output of ST-LINK (default OFF on board)
 * LSE - 32.768 kHz
 */

#define STM32_BOARD_XTAL        8000000ul

#define STM32_HSI_FREQUENCY     16000000ul
#define STM32_LSI_FREQUENCY     32000            /* Between 30kHz and 60kHz */
#define STM32_HSE_FREQUENCY     STM32_BOARD_XTAL
#define STM32_LSE_FREQUENCY     32768            /* X2 on board */

/* PLL source is HSI/1, PLL multipler is 4: PLL frequency is 16MHz (XTAL) x 4 = 64MHz */

#define STM32_CFGR_PLLSRC       0
#define STM32_CFGR_PLLXTPRE     0
#define STM32_CFGR_PLLMUL       RCC_CFGR_PLLMUL_CLKx4
#define STM32_PLL_FREQUENCY     (4*STM32_HSI_FREQUENCY)

/* Use the PLL and set the SYSCLK source to be the PLL/2 (32MHz) */

#define STM32_SYSCLK_SW         RCC_CFGR_SW_PLL
#define STM32_SYSCLK_SWS        RCC_CFGR_SWS_PLL
#define STM32_CFGR_PLLDIV       RCC_CFGR_PLLDIV_2
#define STM32_SYSCLK_FREQUENCY  STM32_PLL_FREQUENCY/2

/* AHB clock (HCLK) is SYSCLK (32MHz) */

#define STM32_RCC_CFGR_HPRE     RCC_CFGR_HPRE_SYSCLK
#define STM32_HCLK_FREQUENCY    STM32_SYSCLK_FREQUENCY
#define STM32_BOARD_HCLK        STM32_HCLK_FREQUENCY

/* APB2 clock (PCLK2) is HCLK (32MHz) */

#define STM32_RCC_CFGR_PPRE2    RCC_CFGR_PPRE2_HCLK
#define STM32_PCLK2_FREQUENCY   STM32_HCLK_FREQUENCY
#define STM32_APB2_CLKIN        (STM32_PCLK2_FREQUENCY)

/* APB1 clock (PCLK1) is HCLK/2 (16MHz) */

#define STM32_RCC_CFGR_PPRE1    RCC_CFGR_PPRE1_HCLKd2
#define STM32_PCLK1_FREQUENCY   (STM32_HCLK_FREQUENCY/2)

/* 48MHz clock configuration */

#if defined(CONFIG_STM32F0L0G0_USB) || defined(CONFIG_STM32F0L0G0_RNG)
#  define STM32_USE_CLK48       1
#  define STM32_CLK48_SEL       RCC_CCIPR_CLK48SEL_HSI48
#  define STM32_HSI48_SYNCSRC   SYNCSRC_NONE
#endif

/* TODO: timers */

/* LED definitions **********************************************************/
/* The Nucleo LO73RZ board has three LEDs.  Two of these are controlled by
 * logic on the board and are not available for software control:
 *
 * LD1 COM:  LD1 default status is red.  LD1 turns to green to indicate that
 *           communications are in progress between the PC and the
 *           ST-LINK/V2-1.
 * LD3 PWR:  red LED indicates that the board is powered.
 *
 * And one can be controlled by software:
 *
 * User LD2: green LED is a user LED connected to the I/O PA5 of the
 *           STM32LO73RZ.
 *
 * If CONFIG_ARCH_LEDS is not defined, then the user can control the LED in
 * any way.  The following definition is used to access the LED.
 */

/* LED index values for use with board_userled() */

#define BOARD_LED1       0 /* User LD2 */
#define BOARD_NLEDS      1

/* LED bits for use with board_userled_all() */

#define BOARD_LED1_BIT   (1 << BOARD_LED1)

/* If CONFIG_ARCH_LEDs is defined, then NuttX will control the LED on board
 * the Nucleo LO73RZ.  The following definitions describe how NuttX controls
 * the LED:
 *
 *   SYMBOL              Meaning                  LED1 state
 *   ------------------  -----------------------  ----------
 *   LED_STARTED         NuttX has been started   OFF
 *   LED_HEAPALLOCATE    Heap has been allocated  OFF
 *   LED_IRQSENABLED     Interrupts enabled       OFF
 *   LED_STACKCREATED    Idle stack created       ON
 *   LED_INIRQ           In an interrupt          No change
 *   LED_SIGNAL          In a signal handler      No change
 *   LED_ASSERTION       An assertion failed      No change
 *   LED_PANIC           The system has crashed   Blinking
 *   LED_IDLE            STM32 is is sleep mode   Not used
 */

#define LED_STARTED      0
#define LED_HEAPALLOCATE 0
#define LED_IRQSENABLED  0
#define LED_STACKCREATED 1
#define LED_INIRQ        2
#define LED_SIGNAL       2
#define LED_ASSERTION    2
#define LED_PANIC        1

/* Button definitions *******************************************************/
/* The Nucleo LO73RZ supports two buttons; only one button is controllable
 * by software:
 *
 *   B1 USER:  user button connected to the I/O PB2/PA0 of the STM32LO73RZ.
 *   B2 RESET: push button connected to NRST is used to RESET the
 *             STM32LO73RZ.
 */

#define BUTTON_USER      0
#define NUM_BUTTONS      1

#define BUTTON_USER_BIT  (1 << BUTTON_USER)

/* Alternate function pin selections ****************************************/

/* CMWX1ZZABZ-091 module pinout and internal connections
 *
 * STM32L072CZ | Function
 * ------------+-----------
 * PC0         | SX1276_CE (NRESET)
 * PA7         | SX1276_MOSI
 * PA6         | SX1276_MISO
 * PB3         | SX1276_SCK
 * PA15        | SX1276_NSS
 * PB4         | SX1276_DIO0
 * PB1         | SX1276_DIO1
 * PB0         | SX1276_DIO2
 * PC13        | SX1276_DIO3
 * PA5         | SX1276_DIO4 optional / LED5
 * PA4         | SX1276_DIO5 optional
 * PA1         | CRF1
 * PC1         | CRF2
 * PC2         | CRF3
 * PA3         | STLINK Virtual COM RX
 * PA2         | STLINK Virtual COM TX
 * PA10        | USART1_RX
 * PA9         | USART1_TX
 * PB15        | SPI2_MOSI
 * PB14        | SPI2_MISO
 * PB13        | SPI2_SCK
 * PB12        | SPI2_NSS
 * PB5         | LPTIM1_INI / LED2
 * PB6         | LPTIM1_ETR / LED3
 * PB7         | LPTIM1_IN2 / LED4
 * PB2         | LPTIM1_OUT / BUTTON
 * PA0         | BUTTON (optional)
 * PB9         | I2C1_SDA
 * PB8         | I2C1_SCL
 * PA12        | USB_DP optional / TCXO_VCC
 * PA11        | USB_DM optional
 *
 */

/* USART */

/* USART1 */

#define GPIO_USART1_RX GPIO_USART1_RX_1 /* PA10 */
#define GPIO_USART1_TX GPIO_USART1_TX_1 /* PA9 */

/* By default the USART2 is connected to STLINK Virtual COM Port:
 * USART2_RX - PA3
 * USART2_TX - PA2
 */

#define GPIO_USART2_RX GPIO_USART2_RX_1 /* PA3 */
#define GPIO_USART2_TX GPIO_USART2_TX_1 /* PA2 */

/* SPI */

/* SPI1 is connected to SX1276 radio */

#define GPIO_SPI1_MOSI GPIO_SPI1_MOSI_2 /* PA7 */
#define GPIO_SPI1_MISO GPIO_SPI1_MISO_2 /* PA6 */
#define GPIO_SPI1_SCK  GPIO_SPI1_SCK_2  /* PB3 */
#define GPIO_SPI1_NSS  GPIO_SPI1_NSS_1  /* PA15 */

/* SPI2  */

#define GPIO_SPI2_MOSI GPIO_SPI2_MOSI_1 /* PB15 */
#define GPIO_SPI2_MISO GPIO_SPI2_MISO_1 /* PB14 */
#define GPIO_SPI2_SCK  GPIO_SPI2_SCK_3  /* PB13 */
#define GPIO_SPI2_NSS  GPIO_SPI2_NSS_1  /* PB12 */

/* I2C */

/* I2C1 */

#define GPIO_I2C1_SDA  GPIO_I2C1_SDA_2 /* PB9 */
#define GPIO_I2C1_SCL  GPIO_I2C1_SCL_2 /* PB8 */

/* DMA channels *************************************************************/
/* ADC */

#define ADC1_DMA_CHAN DMACHAN_ADC1_1    /* DMA1_CH1 */

#endif /* __BOARDS_ARM_NUCLEO_LO73RZ_INCLUDE_BOARD_H */