mirror of
https://github.com/apache/nuttx.git
synced 2026-05-29 04:19:37 +08:00
Added Adafruit QT Py RP2040 board.
Added ability to configure indivdual UART, SPI and I2C pin location.
This commit is contained in:
curuvar
Xiang Xiao
@@ -55,9 +55,10 @@ the power.
|
||||
|
||||
Pin Mapping
|
||||
===========
|
||||
Pads numbered anticlockwise from USB connector.
|
||||
|
||||
===== ========== ==========
|
||||
Pin Signal Notes
|
||||
Pad Signal Notes
|
||||
===== ========== ==========
|
||||
1 Reset Pull to ground to reset the RP2040 processor.
|
||||
2 3.3V Power out to peripherals.
|
||||
|
||||
@@ -50,9 +50,10 @@ A ws2812 (NeoPixel) smart RGB LED controlled by GPIO17.
|
||||
|
||||
Pin Mapping
|
||||
===========
|
||||
Pads numbered anticlockwise from USB connector.
|
||||
|
||||
===== ========== ==========
|
||||
Pin Signal Notes
|
||||
Pad Signal Notes
|
||||
===== ========== ==========
|
||||
1 D+ Alternate USB data connection.
|
||||
2 GPIO0 Default TX for UART0 serial console
|
||||
|
||||
Binary file not shown.
|
After Width: | Height: | Size: 125 KiB |
@@ -0,0 +1,119 @@
|
||||
=======================
|
||||
Adafruit QT Py RP2040
|
||||
=======================
|
||||
|
||||
The QT Py RP2040 is a tiny general purpose RP2040 board supplied by
|
||||
Adafruit.
|
||||
|
||||
.. figure:: QT-Py.png
|
||||
:align: center
|
||||
|
||||
Features
|
||||
========
|
||||
|
||||
* RP2040 microcontroller chip
|
||||
* Dual-core ARM Cortex M0+ processor, flexible clock running up to 133 MHz
|
||||
* 264kB of SRAM, and 8MB of on-board Flash memory
|
||||
* Castellated module allows soldering direct to carrier boards
|
||||
* USB Host and Device support via type C connector.
|
||||
* Low-power sleep and dormant modes
|
||||
* Drag & drop programming using mass storage over USB
|
||||
* 13 multi-function GPIO pins (11 breakout pads and two QT pads)
|
||||
* 2× SPI, 2× I2C, 2× UART, 4× 12-bit ADC, 16× controllable PWM channels
|
||||
* Accurate clock and timer on-chip
|
||||
* Temperature sensor
|
||||
* Accelerated floating point libraries on-chip
|
||||
* 8 × Programmable IO (PIO) state machines for custom peripheral support
|
||||
|
||||
Serial Console
|
||||
==============
|
||||
|
||||
By default a serial console appears on GPIO pins 20 (RX GPIO1) and pin 5
|
||||
(TX GPIO1). This console runs a 115200-8N1.
|
||||
|
||||
The board can be configured to use the USB connection as the serial console.
|
||||
|
||||
Buttons and LEDs
|
||||
================
|
||||
|
||||
A ws2812 (NeoPixel) smart RGB LED controlled by GPIO12 (data) and
|
||||
GPIO11 (power).
|
||||
|
||||
There is a BOOT button which if held down when power is first
|
||||
applied or the RESET button is pressed will cause the RP2040 to
|
||||
boot into program mode and appear as a storage device to
|
||||
a USB connecter. Saving a .UF2 file to this device will
|
||||
replace the Flash ROM contents on the RP2040.
|
||||
|
||||
A RESET button that allows rebooting the board without disconnecting
|
||||
the power.
|
||||
|
||||
Pin Mapping
|
||||
===========
|
||||
Pads numbered anticlockwise from USB connector.
|
||||
|
||||
===== ========== ==========
|
||||
Pad Signal Notes
|
||||
===== ========== ==========
|
||||
1 GPIO26 ADC0
|
||||
2 GPIO27 ADC1
|
||||
3 GPIO28 ADC2
|
||||
4 GPIO29 ADC3
|
||||
5 GPIO24
|
||||
6 GPIO25
|
||||
7 GPIO20 Default TX for UART1 serial console
|
||||
8 GPIO5 Default RX for UART1 serial console
|
||||
9 GPIO6
|
||||
10 GPIO4
|
||||
11 GPIO3
|
||||
12 3.3V Power out to peripherals.
|
||||
13 Ground
|
||||
14 5V
|
||||
===== ========== ==========
|
||||
|
||||
The board has a STEMMA QT connector that is also connected to
|
||||
pins GPIO22 (I2C1 SDA) and GPIO23 (I2C1 SCL).
|
||||
|
||||
Power Supply
|
||||
============
|
||||
|
||||
The Raspberry Pi Pico can be powered via the USB connector,
|
||||
or by supplying +5V to pin 14. The board had a diode that prevents
|
||||
power from pin 14 from flowing back to the USB socket, although
|
||||
this can be disabled by connecting on-board solder pads if there
|
||||
is need to run as a usb host.
|
||||
|
||||
The Raspberry Pi Pico chip run on 3.3 volts which is supplied by
|
||||
an on board regulator.
|
||||
|
||||
|
||||
Configurations
|
||||
==============
|
||||
|
||||
gpio
|
||||
--------
|
||||
|
||||
NuttShell configuration (console enabled in UART1, at 115200 bps) with GPIO examples.
|
||||
|
||||
nsh
|
||||
---
|
||||
|
||||
Basic NuttShell configuration (console enabled in UART1, at 115200 bps).
|
||||
|
||||
nshsram
|
||||
-------
|
||||
|
||||
NuttShell configuration (console enabled in UART1, at 115200 bps) with interrupt
|
||||
vectors in RAM.
|
||||
|
||||
smp
|
||||
---
|
||||
|
||||
Basic NuttShell configuration (console enabled in UART1, at 115200 bps) with
|
||||
both ARM cores enabled.
|
||||
|
||||
usbnsh
|
||||
------
|
||||
|
||||
Basic NuttShell configuration (console enabled in USB Port, at 115200 bps).
|
||||
|
||||
@@ -46,9 +46,10 @@ on the RP2040.
|
||||
|
||||
Pin Mapping
|
||||
===========
|
||||
Pads numbered anticlockwise from USB connector.
|
||||
|
||||
===== ========== ==========
|
||||
Pin Signal Notes
|
||||
Pad Signal Notes
|
||||
===== ========== ==========
|
||||
1 VBUS Connected to USB +5V
|
||||
2 Ground
|
||||
|
||||
@@ -46,9 +46,10 @@ on the RP2040.
|
||||
|
||||
Pin Mapping
|
||||
===========
|
||||
Pads numbered anticlockwise from USB connector.
|
||||
|
||||
===== ========== ==========
|
||||
Pin Signal Notes
|
||||
Pad Signal Notes
|
||||
===== ========== ==========
|
||||
1 GPIO0 Default TX for UART0 serial console
|
||||
2 GPIO1 Default RX for UART1 serial console
|
||||
|
||||
Reference in New Issue
Block a user