configs/stm32f439i-disco: Add an fb configuration

configs/open1788/src/lpc17_bringup.c

@@ -389,7 +389,7 @@ int lpc17_bringup(void)
     }
 
 #ifdef CONFIG_VIDEO_FB
-  /* Initialize and register the simulated framebuffer driver */
+  /* Initialize and register the framebuffer driver */
 
   ret = fb_register(0, 0);
   if (ret < 0)

configs/stm32f429i-disco/README.txt

@@ -677,10 +677,12 @@ Where <subdir> is one of the following:
        external RS-232 line driver to the UART1 pins of the DISCO board
        on PA9 and PA10 of connector P1.
 
-  ltdc:
+  fb
-  ----
+  --
-    STM32F429I-DISCO LTDC Framebuffer demo example.  See
+
-    configs/stm32f429i-disco/ltdc/README.txt for additional information.
+    STM32F429I-DISCO LTDC Framebuffer demo example.  This is a simple
+    configuration used for some basic (non-graphic) debug of the framebuffer
+    character drivers using apps/examples/fb.
 
   nsh:
   ---

configs/stm32f429i-disco/fb/README.txt

@@ -0,0 +1,70 @@
+README.txt
+==========
+
+STM32F429I-DISCO LTDC Framebuffer demo example
+
+Configure and build
+-----------------------------------------------
+cd tools
+./configure -a <appdir> stm32f429i-disco/ltdc
+cd ..
+make
+
+Note!
+In the current implementation the DMA2D driver only supports clut pixel format
+if the LTDC driver it does. Otherwise it will not be compatible with the nx
+framework. If CONFIG_FB_CMAP is configured, nx expects that any pixel format
+supports color lookup tables. This is also the case for non CLUT formats e.g.
+FB_FMT_RGB16_565. This may result in wrong color representation by nx if the
+pixel format is unequal to FB_FMT_RGB8.
+
+On the other hand layers with CLUT pixel format are not supported by the DMA2D
+controller, in the case they will be used as destination layer for the following
+operations:
+- blit
+- blend
+- fillarea
+
+To enable clut support in both LTDC and DMA2D driver the following
+configurations are valid:
+
+1.
+- Enable LTDC_INTERFACE and LAYER1/LAYER2
+- Layer1 FB_FMT_RGB8
+- Layer2 any non clut format
+
+But Layer2 can only be used as destination layer for dma2d operations above.
+This configuration is not compatibly to nx because LAYER2 will be referenced
+by up_fbgetvplane and is an invalid CLUT pixel format.
+
+2.
+- Enable LTDC_INTERFACE and LAYER1/LAYER2
+- Layer2 FB_FMT_RGB8
+- Layer1 any non clut format
+
+But Layer1 can only be used as destination layer for dma2d operations above.
+This configuration should be compatibly to nx because LAYER2 will be referenced
+by up_fbgetvplane and is an valid CLUT pixel format.
+
+All other non clut configuration work fine.
+
+If using the DMA2D controller without the LTDC controller e.g. camera interface
+than enable CONFIG_FB_CMAP and optional CONFIG_FB_TRANSPARENCY in your board
+specific configuration.
+
+
+Loading
+-----------------------------------------------
+st-flash write nuttx.bin 0x8000000
+
+Executing
+-----------------------------------------------
+The ltdc is initialized during boot up.
+Interaction with NSH is via the serial console at 115200 8N1 baud.
+From the nsh comandline execute one (or both) of the examples:
+- nx (default nx example)
+- ltdc (trivial ltdc interface test)
+
+Note! The ltdc example ends in an infinite loop. To get control of the nsh
+start this example in the background with 'ltdc &'.
+

configs/stm32f429i-disco/fb/defconfig

@@ -0,0 +1,78 @@
+# CONFIG_ARCH_FPU is not set
+# CONFIG_NX_DISABLE_16BPP is not set
+# CONFIG_STM32_DMA2D_RGB888 is not set
+# CONFIG_STM32_FLASH_PREFETCH is not set
+CONFIG_ARCH_BOARD_STM32F429I_DISCO=y
+CONFIG_ARCH_BOARD="stm32f429i-disco"
+CONFIG_ARCH_BUTTONS=y
+CONFIG_ARCH_CHIP_STM32=y
+CONFIG_ARCH_CHIP_STM32F429Z=y
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_ARCH="arm"
+CONFIG_ARMV7M_TOOLCHAIN_CODESOURCERYL=y
+CONFIG_BOARD_INITIALIZE=y
+CONFIG_BOARD_LOOPSPERMSEC=16717
+CONFIG_BUILTIN=y
+CONFIG_DEBUG_CUSTOMOPT=y
+CONFIG_DEBUG_SYMBOLS=y
+CONFIG_DISABLE_POLL=y
+CONFIG_DRIVERS_VIDEO=y
+CONFIG_EXAMPLES_FB=y
+CONFIG_EXAMPLES_NSH_CXXINITIALIZE=y
+CONFIG_EXAMPLES_NSH=y
+CONFIG_EXAMPLES_NX_BPP=16
+CONFIG_EXAMPLES_NX=y
+CONFIG_FS_PROCFS_REGISTER=y
+CONFIG_FS_PROCFS=y
+CONFIG_HAVE_CXX=y
+CONFIG_HAVE_CXXINITIALIZE=y
+CONFIG_HEAP2_BASE=0xD0000000
+CONFIG_HEAP2_SIZE=8081408
+CONFIG_INTELHEX_BINARY=y
+CONFIG_MAX_TASKS=16
+CONFIG_MAX_WDOGPARMS=2
+CONFIG_MM_REGIONS=2
+CONFIG_MQ_MAXMSGSIZE=64
+CONFIG_NFILE_DESCRIPTORS=8
+CONFIG_NFILE_STREAMS=8
+CONFIG_NSH_BUILTIN_APPS=y
+CONFIG_NSH_FILEIOSIZE=512
+CONFIG_NSH_LINELEN=64
+CONFIG_NSH_READLINE=y
+CONFIG_NX_BLOCKING=y
+CONFIG_NX=y
+CONFIG_NXFONT_MONO5X8=y
+CONFIG_PREALLOC_MQ_MSGS=4
+CONFIG_PREALLOC_TIMERS=4
+CONFIG_PREALLOC_WDOGS=4
+CONFIG_RAM_SIZE=114688
+CONFIG_RAM_START=0x20000000
+CONFIG_RAW_BINARY=y
+CONFIG_RR_INTERVAL=200
+CONFIG_SCHED_WAITPID=y
+CONFIG_SDCLONE_DISABLE=y
+CONFIG_SPI_CMDDATA=y
+CONFIG_START_DAY=6
+CONFIG_START_MONTH=12
+CONFIG_START_YEAR=2011
+CONFIG_STM32_CCM_PROCFS=y
+CONFIG_STM32_CCMEXCLUDE=y
+CONFIG_STM32_DISABLE_IDLE_SLEEP_DURING_DEBUG=y
+CONFIG_STM32_DMA2D_NLAYERS=4
+CONFIG_STM32_DMA2D=y
+CONFIG_STM32_FSMC_SRAM=y
+CONFIG_STM32_FSMC=y
+CONFIG_STM32_JTAG_SW_ENABLE=y
+CONFIG_STM32_LTDC_FB_BASE=0xD07B5000
+CONFIG_STM32_LTDC_FB_SIZE=307200
+CONFIG_STM32_LTDC_INTERFACE=y
+CONFIG_STM32_LTDC=y
+CONFIG_STM32_PWR=y
+CONFIG_STM32_SPI5=y
+CONFIG_STM32_USART1=y
+CONFIG_STM32F429I_DISCO_ILI9341=y
+CONFIG_TASK_NAME_SIZE=0
+CONFIG_USART1_SERIAL_CONSOLE=y
+CONFIG_USER_ENTRYPOINT="nsh_main"
+CONFIG_VIDEO_FB=y
+CONFIG_WDOG_INTRESERVE=0

configs/stm32f429i-disco/src/stm32_appinit.c

@@ -55,6 +55,10 @@
 #  include <nuttx/mtd/mtd.h>
 #endif
 
+#ifdef CONFIG_VIDEO_FB
+#  include <nuttx/video/fb.h>
+#endif
+
 #ifdef CONFIG_USBMONITOR
 #  include <nuttx/usb/usbmonitor.h>
 #endif
@@ -340,9 +344,19 @@ int board_app_initialize(uintptr_t arg)
 #endif /* CONFIG_MTD */
 #endif /* CONFIG_STM32_SPI4 */
 
-  /* Create a RAM MTD device if configured */
+#ifdef CONFIG_VIDEO_FB
+  /* Initialize and register the framebuffer driver */
+
+  ret = fb_register(0, 0);
+  if (ret < 0)
+    {
+      syslog(LOG_ERR, "ERROR: fb_register() failed: %d\n", ret);
+    }
+#endif
 
 #if defined(CONFIG_RAMMTD) && defined(CONFIG_STM32F429I_DISCO_RAMMTD)
+  /* Create a RAM MTD device if configured */
+
   {
     uint8_t *start = (uint8_t *) kmm_malloc(CONFIG_STM32F429I_DISCO_RAMMTD_SIZE * 1024);
     mtd = rammtd_initialize(start, CONFIG_STM32F429I_DISCO_RAMMTD_SIZE * 1024);