STM32F746G-DISCO: Add a network-enabled NSH configuratino for network testing

configs/stm32f746g-disco/README.txt

@@ -489,9 +489,20 @@ Configurations
 Configuration Directories
 -------------------------
 
+  netnsh:
+  ------
+    This is a NetShell (NSH) very similar to the nsh configuration described
+    below.  It differs in that it has networking enabled.
+
+    NOTES:
+
+    1. Both IPv4 and IPv6 protocoals are enabled.
+
+    2. UDP, TCIP/IP, ARP, ICMP, and ICMPv6 are also enabled.
+
   nsh:
   ---
-    Configures the NuttShell (nsh) located at apps/examples/nsh.  The
+    Configures the NuttShell (NSH) located at apps/examples/nsh.  The
     Configuration enables the serial interfaces on UART6.  Support for
     builtin applications is enabled, but in the base configuration no
     builtin applications are selected.

configs/stm32f746g-disco/include/board.h

@@ -264,15 +264,12 @@
 #define LED_PANIC                    3 /* LD1=flashing */
 
 /* Button definitions ***************************************************************/
-/*   Pushbutton B1, labelled "User", is connected to GPIO PI11.  A high
+/* The STM32F7 Discovery supports one button:  Pushbutton B1, labelled "User", is
-  value will be sensed when the button is depressed.
+ * connected to GPIO PI11.  A high value will be sensed when the button is depressed.
-
+ */
-/* The STM32F7 Discovery supports one button: */
 
 #define BUTTON_USER        0
-
 #define NUM_BUTTONS        1
-
 #define BUTTON_USER_BIT    (1 << BUTTON_USER)
 
 /* Alternate function pin selections ************************************************/
@@ -294,6 +291,28 @@
 #define GPIO_USART6_RX GPIO_USART6_RX_1
 #define GPIO_USART6_TX GPIO_USART6_TX_1
 
+/* The STM32 F7 connects to a SMSC LAN8742A PHY using these pins:
+ *   STM32 F7 BOARD        LAN8742A
+ *   GPIO     SIGNAL       PIN NAME
+ *   -------- ------------ -------------
+ *   PG11     RMII_TX_EN   TXEN
+ *   PG13     RMII_TXD0    TXD0
+ *   PG14     RMII_TXD1    TXD1
+ *   PC4      RMII_RXD0    RXD0/MODE0
+ *   PC5      RMII_RXD1    RXD1/MODE1
+ *   PG2      RMII_RXER    RXER/PHYAD0
+ *   PA7      RMII_CRS_DV  CRS_DV/MODE2
+ *   PC1      RMII_MDC     MDC
+ *   PA2      RMII_MDIO    MDIO
+ *   N/A      NRST         nRST
+ *   PA1      RMII_REF_CLK nINT/REFCLK0
+ *   N/A      OSC_25M      XTAL1/CLKIN
+ */
+
+#define GPIO_ETH_RMII_TX_EN   GPIO_ETH_RMII_TX_EN_2
+#define GPIO_ETH_RMII_TXD0    GPIO_ETH_RMII_TXD0_2
+#define GPIO_ETH_RMII_TXD1    GPIO_ETH_RMII_TXD1_2
+
 /************************************************************************************
  * Public Data
  ************************************************************************************/

configs/stm32f746g-disco/netnsh/Make.defs

@@ -0,0 +1,112 @@
+############################################################################
+# configs/stm32f746g-disco/netnsh/Make.defs
+#
+#   Copyright (C) 2015 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+############################################################################
+
+include ${TOPDIR}/.config
+include ${TOPDIR}/tools/Config.mk
+include ${TOPDIR}/arch/arm/src/armv7-m/Toolchain.defs
+
+LDSCRIPT = flash.ld
+
+ifeq ($(WINTOOL),y)
+  # Windows-native toolchains
+  DIRLINK = $(TOPDIR)/tools/copydir.sh
+  DIRUNLINK = $(TOPDIR)/tools/unlink.sh
+  MKDEP = $(TOPDIR)/tools/mknulldeps.sh
+  ARCHINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}"
+  ARCHXXINCLUDES = -I. -isystem "${shell cygpath -w $(TOPDIR)/include}" -isystem "${shell cygpath -w $(TOPDIR)/include/cxx}"
+  ARCHSCRIPT = -T "${shell cygpath -w $(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/scripts/$(LDSCRIPT)}"
+else
+  # Linux/Cygwin-native toolchain
+  MKDEP = $(TOPDIR)/tools/mkdeps.sh
+  ARCHINCLUDES = -I. -isystem $(TOPDIR)/include
+  ARCHXXINCLUDES = -I. -isystem $(TOPDIR)/include -isystem $(TOPDIR)/include/cxx
+  ARCHSCRIPT = -T$(TOPDIR)/configs/$(CONFIG_ARCH_BOARD)/scripts/$(LDSCRIPT)
+endif
+
+CC = $(CROSSDEV)gcc
+CXX = $(CROSSDEV)g++
+CPP = $(CROSSDEV)gcc -E
+LD = $(CROSSDEV)ld
+AR = $(ARCROSSDEV)ar rcs
+NM = $(ARCROSSDEV)nm
+OBJCOPY = $(CROSSDEV)objcopy
+OBJDUMP = $(CROSSDEV)objdump
+
+ARCHCCVERSION = ${shell $(CC) -v 2>&1 | sed -n '/^gcc version/p' | sed -e 's/^gcc version \([0-9\.]\)/\1/g' -e 's/[-\ ].*//g' -e '1q'}
+ARCHCCMAJOR = ${shell echo $(ARCHCCVERSION) | cut -d'.' -f1}
+
+ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
+  ARCHOPTIMIZATION = -g
+endif
+
+ifneq ($(CONFIG_DEBUG_NOOPT),y)
+  ARCHOPTIMIZATION += $(MAXOPTIMIZATION) -fno-strict-aliasing -fno-strength-reduce -fomit-frame-pointer
+endif
+
+ARCHCFLAGS = -fno-builtin
+ARCHCXXFLAGS = -fno-builtin -fno-exceptions -fno-rtti
+ARCHWARNINGS = -Wall -Wstrict-prototypes -Wshadow
+ARCHWARNINGSXX = -Wall -Wshadow
+ARCHDEFINES =
+ARCHPICFLAGS = -fpic -msingle-pic-base -mpic-register=r10
+
+CFLAGS = $(ARCHCFLAGS) $(ARCHWARNINGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
+CXXFLAGS = $(ARCHCXXFLAGS) $(ARCHWARNINGSXX) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES) -pipe
+CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
+CPPFLAGS = $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRADEFINES)
+AFLAGS = $(CFLAGS) -D__ASSEMBLY__
+
+NXFLATLDFLAGS1 = -r -d -warn-common
+NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat-pcrel.ld -no-check-sections
+LDNXFLATFLAGS = -e main -s 2048
+
+OBJEXT = .o
+LIBEXT = .a
+EXEEXT =
+
+ifneq ($(CROSSDEV),arm-nuttx-elf-)
+  LDFLAGS += -nostartfiles -nodefaultlibs
+endif
+ifeq ($(CONFIG_DEBUG_SYMBOLS),y)
+  LDFLAGS += -g
+endif
+
+
+HOSTCC = gcc
+HOSTINCLUDES = -I.
+HOSTCFLAGS = -Wall -Wstrict-prototypes -Wshadow -g -pipe
+HOSTLDFLAGS =
+

configs/stm32f746g-disco/netnsh/setenv.sh

@@ -0,0 +1,77 @@
+#!/bin/bash
+# configs/stm32f746g-disco/netnsh/setenv.sh
+#
+#   Copyright (C) 2015 Gregory Nutt. All rights reserved.
+#   Author: Gregory Nutt <gnutt@nuttx.org>
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# 1. Redistributions of source code must retain the above copyright
+#    notice, this list of conditions and the following disclaimer.
+# 2. Redistributions in binary form must reproduce the above copyright
+#    notice, this list of conditions and the following disclaimer in
+#    the documentation and/or other materials provided with the
+#    distribution.
+# 3. Neither the name NuttX nor the names of its contributors may be
+#    used to endorse or promote products derived from this software
+#    without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+# POSSIBILITY OF SUCH DAMAGE.
+#
+
+if [ "$_" = "$0" ] ; then
+  echo "You must source this script, not run it!" 1>&2
+  exit 1
+fi
+
+WD=`pwd`
+if [ ! -x "setenv.sh" ]; then
+  echo "This script must be executed from the top-level NuttX build directory"
+  exit 1
+fi
+
+if [ -z "${PATH_ORIG}" ]; then
+  export PATH_ORIG="${PATH}"
+fi
+
+# This is the Cygwin path to the location where I installed the Atmel GCC
+# toolchain under Windows.  You will also have to edit this if you install
+# this toolchain in any other location
+#export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/Atmel/Atmel Toolchain/ARM GCC/Native/4.7.3.99/arm-gnu-toolchain/bin"
+
+# This is the Cygwin path to the location where I installed the CodeSourcery
+# toolchain under windows.  You will also have to edit this if you install
+# the CodeSourcery toolchain in any other location
+#export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery G++ Lite/bin"
+#export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/CodeSourcery/Sourcery_CodeBench_Lite_for_ARM_EABI/bin"
+# export TOOLCHAIN_BIN="/cygdrive/c/Users/MyName/MentorGraphics/Sourcery_CodeBench_Lite_for_ARM_EABI/bin"
+
+# This is the location where I installed the ARM "GNU Tools for ARM Embedded Processors"
+# You can this free toolchain here https://launchpad.net/gcc-arm-embedded
+export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/GNU Tools ARM Embedded/4.9 2014q4/bin"
+
+# This is the path to the location where I installed the devkitARM toolchain
+# You can get this free toolchain from http://devkitpro.org/ or http://sourceforge.net/projects/devkitpro/
+#export TOOLCHAIN_BIN="/cygdrive/c/Program Files (x86)/devkitARM/bin"
+
+# This is the Cygwin path to the location where I build the buildroot
+# toolchain.
+# export TOOLCHAIN_BIN="${WD}/../buildroot/build_arm_nofpu/staging_dir/bin"
+
+# Add the path to the toolchain to the PATH varialble
+export PATH="${TOOLCHAIN_BIN}:/sbin:/usr/sbin:${PATH_ORIG}"
+
+echo "PATH : ${PATH}"