Fix various typos and spelling errors.

ChangeLog

@@ -3213,7 +3213,7 @@
 	  strings by strerror().
 	* arch/arm/src/stm32/stm32_usbotghost.c:  Finally... the USB OTG FS
 	  appears to handle NAKing correctly.
-	* configs/stm32f4discovery/*:  Added and verifed support for USB OTG FS
+	* configs/stm32f4discovery/*:  Added and verified support for USB OTG FS
 	  host on the STM32F4Discovery board.
 	* configs/*/defconfig: Remove configuration documentation from config
 	  files.  It is redundant, error-prone, and difficult to maintain.
@@ -10053,7 +10053,7 @@
 	  stm32_stdclockconfig() in stm32fxxxxx_rcc.c.  Doing this I checked
 	  the possible uses of the LSI and the LSE sources: the LSI can be used
 	  for RTC and/or the IWDG, while the LSE only for the RTC (and to output
-	  the MCO1 pin). This change is not verifed for any other platforms.
+	  the MCO1 pin). This change is not verified for any other platforms.
 	  From Leo Aloe3132
 	* Rename arch_nshinitialize() to board_app_initialize() (2015-03-30).
 	* ./*.mk, configs/.gitignore, Makefile, boardctl.c, include/nuttx/fs/ioctl,
@@ -19507,7 +19507,7 @@
 	  USART_CR3. This was not being done, so calls to TIOCSSINGLEWIRE were
 	  silently failing.
 	  This change checks the state of UE in USART_CR1, clears the UE bit
-	  before writing HDSEL, then re-enables it if neccesary.  From Kurt
+	  before writing HDSEL, then re-enables it if necessary.  From Kurt
 	  Kiefer (2018-06-14).
 	* drivers/sensors:  Add support for Telair T6713 carbon dioxide
 	  sensor.  From Juha Niskanen (2018-06-15).
@@ -20035,7 +20035,7 @@
 	  the STM32 RTC and use an external RTC you cannot because the external
 	  RTC also depends on the global CONFIG_RTC.  The solution is to add a
 	  new CONFIG_STM32xx_RTC configuration option the permits to you select
-	  or deselect the STM32 RTC but still be able to selecte the external
+	  or deselect the STM32 RTC but still be able to select the external
 	  RTC.  From Gregory Nutt (2018-08-08).
 	* configs/stm32f4discovery/scripts/ld.script:  Missing
 	  EXTERN(_vectors)  From Gregory Nutt (2018-08-08).
@@ -26538,7 +26538,7 @@
 	  automatically if the NuttX math library is selected.  From Gregory
 	  Nutt (2019-09-16).
 	* boards/arm/cxd56xx/spresense/include/board_pinconfig.h:  Add board
-	  specific pin configurations of CXD5602 pins to fit Spresense board. 
+	  specific pin configurations of CXD5602 pins to fit Spresense board.
 	  From Takayoshi Koizumi (2019-09-16).
 	* boards/arm/cxd56xx/spresense/Kconfig:  Add a configuration to select
 	  if an extension board is attached to the SPresence.  If there is no
@@ -26708,7 +26708,7 @@
 	    extension board.  From Alin Jerpelea (2019-09-26).
 	* arch\arm\src\stm32h7\Kconfig:  Add the CRC option in KConfig.  From
 	  Eduard Niesner (2019-09-27).
-	* arch/arm/src/stm32l4/stm32l4_dumpgpio.c: Fix using wrong GPIO enable register. 
+	* arch/arm/src/stm32l4/stm32l4_dumpgpio.c: Fix using wrong GPIO enable register.
 	  From Juha Niskanen (2019-09-27).
 	* boards/arm/stm32/stm32f429i-disco/include/board.h:  Remove forbidden STM32
 	  header file inclusions.  Fix some coding standard issues.  From Gregory Nutt
@@ -26826,7 +26826,7 @@
 	  other SMP architectures as well.  From Gregory Nutt (2019-10-04).
 	* sched/wdog/wd_start.c:  Back out a kludge-workaround for an SDCC
 	  compiler problem fix back in Feb 2017.  That workaround now appears to
-	  conflict with newer GCC versions using unsupport warning options. 
+	  conflict with newer GCC versions using unsupport warning options.
 	  From Gregory Nutt (2019-10-04).
 	* drivers/wireless/bluetooth/bt_uart_bcm4343x.c:  BCM4343x HCIUART
 	  support.  From Dave Marples (2019-10-04).
@@ -26835,7 +26835,7 @@
 	  (2019-10-04).
 	* boards/arm/tiva/tm4c123g-launchpad/: SPI CAN functionality on
 	  TM4C123GXL - ek-tm4c123gxl_spi_can.  From DisruptiveNL (2019-10-05).
-	* arch/sim/src/sim/up_hostfs.c:   hostfs skip '.' and '..' in readdir' 
+	* arch/sim/src/sim/up_hostfs.c:   hostfs skip '.' and '..' in readdir'
 	  From Xiang Xiao (2019-10-07).
 	* tools/mkromfsimg.sh:  Use sed to add const to ROMFS declarations so
 	  that they like in FLASH not RAM.  From Bernd Walter (2019-10-07).
@@ -26854,7 +26854,7 @@
 	    overflow on some calculations.
 	  From Daniel Pereira Volpato (2019-10-07).
 	* boards/arm/stm32f0l0g0/nucleo-g070rb/include/board.h: Add TIMx clock
-	  frequencies boards/arm/stm32f0l0g0/nucleo-g070rb: Enable basic timers 
+	  frequencies boards/arm/stm32f0l0g0/nucleo-g070rb: Enable basic timers
 	  From Daniel Pereira Volpato (2019-10-07).
 	* drivers/wireless/bluetooth/bt_uart_bcm4343x.c:  Fix small a small bug
 	  found during testing.
@@ -26944,7 +26944,7 @@
 	  be ignored.  From liuhaitao (2019-10-17).
 	* tools/LibTargets.mk:  Make libapps.a by the default target.  From
 	  Xiang Xiao (2019-10-17).
-	* include/nuttx/timers/pwm.h:  Correct some typos. 
+	* include/nuttx/timers/pwm.h:  Correct some typos.
 	  arch/arm/src/stm32f0l0g0: Add PWM support.  From Daniel Pereira
 	  Volpato (2019-10-17).
 	* boards/arm/stm32f0l0g0/nucleo-g070rb: Add PWM support and GPIO_TIM3_*
@@ -27010,7 +27010,7 @@
 	* stm32f4dis with gs2200m:
 	  - drivers: wireless: Add SPI_SELECT() to _read/write_data() in gs2200m.c
 	  - boards: stm32f4discovery: Add support for gs2200m.  NOTE: GS2200M
-	    for Spresense works with mikroe STM32F4 Discovery Shield (slot3) 
+	    for Spresense works with mikroe STM32F4 Discovery Shield (slot3)
 	    From Masayuki Ishikawa (2019-10-22).
 	* STM32H7:  Flash driver and Serious BUG fixes:
 	  - arch/arm/Kconfig:Add ARCH_HAVE_PROGMEM for STM32H7
@@ -27126,7 +27126,7 @@
 	  (2019-10-26).
 	* tools/nxstyle.c:  Eliminate false alarms when checking for alignment
 	  of comments to the right of code.  Fix check for C++ style comments so
-	  that strings like http:// and https:// do not generate false alarms. 
+	  that strings like http:// and https:// do not generate false alarms.
 	  From Gregory Nutt (2019-10-27).
 	* boards/arm/sama5/sama5d4-ek/src/sam_appinit.c:  Fix error found in
 	  build testing.  Bad conditional compilation for
@@ -27459,7 +27459,7 @@
 	  imx1060-evk to remove compilation warnings about duplicated
 	  definitions. No functional changes.  From Dave Marples (2019-11-10).
 	* arch/sim/src/sim/up_simuart.c:  Remove CONFIG_SIM_UART_DATAPOST for
-	  arch/sim.  It's very dangerous to call NuttX API from simuart_thread. 
+	  arch/sim.  It's very dangerous to call NuttX API from simuart_thread.
 	  From Xiang Xiao (2019-11-10).
 	* arch/sim/src/sim:  Replace all CONFIG_DEV_CONSOLE with USE_DEVCONSOLE
 	  for arch/sim and compile up_devconsole.c conditionally.  From Xiang
@@ -27499,7 +27499,7 @@
 	* arch/arm/src/imxrt/imxrt_idle.c:  Y'all remember that conversation we
 	  had about why WFI might have been disabled on imxrt? Well, looks like
 	  we found the reason:
-	  - https://github.com/zephyrproject-rtos/zephyr/pull/8535/commits: 
+	  - https://github.com/zephyrproject-rtos/zephyr/pull/8535/commits:
 	    "The imxrt1050 is configured to use SYSTICK for the kernel timer, but
 	    SYSTICK cannot wake up the soc from low-power modes. Disable
 	    low-power modes on this soc until we have support for an alternative

Documentation/NuttX.html

@@ -6421,11 +6421,11 @@ Mem:         29232       5920      23312      23312
     <ul>
       <p>
        <b>STATUS:</b>
-         The basic port was code-complete in NuttX-5.19 and verifed in NuttX-6.0.
+         The basic port was code-complete in NuttX-5.19 and verified in NuttX-6.0.
          The port was verified using the OS and NuttShell (NSH) examples under QEMU.
          The port is reported to be functional on the <a href="http://bifferos.bizhat.com">Bifferboard</a> as well.
          In NuttX 7.1, Lizhuoyi contributed additional keyboard and VGA drivers.
-         This is a great, stable starting point for anyone interest in fleshing out the x86 port!
+         This is a great, stable starting point for anyone interested in fleshing out the x86 port!
          Refer to the NuttX <a href="https://bitbucket.org/nuttx/nuttx/src/master/boards/x86/qemu/qemu-i486/README.txt" target="_blank">README</a> file for further information.
       </p>
     </ul>

ReleaseNotes

@@ -8787,7 +8787,7 @@ detailed bugfix information):
         stm32fxxxxx_rcc.c.  Doing this I checked the possible uses of the
         LSI and the LSE sources: the LSI can be used for RTC and/or the
         IWDG, while the LSE only for the RTC (and to output the MCO1 pin).
-        This change is not verifed for any other platforms.  From Leo
+        This change is not verified for any other platforms.  From Leo
         Aloe3132
 
     * Tiva Drivers:
@@ -19459,7 +19459,7 @@ detailed bugfix information):
         use an external RTC you cannot because the external RTC also
         depends on the global CONFIG_RTC.  The solution is to add a new
         CONFIG_STM32xx_RTC configuration option the permits to you select
-        or deselect the STM32 RTC but still be able to selecte the external
+        or deselect the STM32 RTC but still be able to select the external
         RTC.  From Gregory Nutt.
       - STM32 F3 I2C:  Fix compile error with I2C reset.  From Juha
         Niskanen.
@@ -19467,7 +19467,7 @@ detailed bugfix information):
         must be disabled in order to write HDSEL in USART_CR3. This was not
         being done, so calls to TIOCSSINGLEWIRE were silently failing.
         This change checks the state of UE in USART_CR1, clears the UE bit
-        before writing HDSEL, then re-enables it if neccesary.  From Kurt
+        before writing HDSEL, then re-enables it if necessary.  From Kurt
         Kiefer.
       - STM32 F7 DMA:  DMA macros did not account for the increase from 8
         to 16 DMA channels.  From Gregory Nutt.

arch/arm/src/kinetis/kinetis_timerisr.c

@@ -122,7 +122,7 @@ void arm_timer_initialize(void)
   regval |= (NVIC_SYSH_PRIORITY_DEFAULT << NVIC_SYSH_PRIORITY_PR15_SHIFT);
   putreg32(regval, NVIC_SYSH12_15_PRIORITY);
 
-  /* Note that is should not be neccesary to set the SYSTICK clock source:
+  /* Note that it should not be necessary to set the SYSTICK clock source:
    * "The CLKSOURCE bit in SysTick Control and Status register is always set
    *  to select the core clock."
    */

arch/arm/src/lpc17xx_40xx/lpc17_40_sdcard.c

@@ -1280,7 +1280,7 @@ static int lpc17_40_interrupt(int irq, void *context, FAR void *arg)
                       lpc17_40_endtransfer(priv, SDIOWAIT_TRANSFERDONE);
                     }
 
-                  /* Otherwise, just disable futher transfer interrupts and
+                  /* Otherwise, just disable further transfer interrupts and
                    * wait for the DMA complete event.
                    */
 

arch/arm/src/sam34/sam4cm_oneshot.h

@@ -84,8 +84,8 @@ struct sam_oneshot_s
                                        * the callback */
 #ifdef CONFIG_SAM34_FREERUN
   volatile uint32_t start_count;      /* Stores the value of the freerun counter,
-                                       * at each start of the onshot timer. Is neccesary
+                                       * at each start of the oneshot timer. Is necessary
-                                       * to find out if the onshot counter was updated
+                                       * to find out if the oneshot counter was updated
                                        * correctly at the time of the call to
                                        * sam_oneshot_cancel or not. */
 #endif

arch/arm/src/sama5/sam_oneshot.h

@@ -84,8 +84,8 @@ struct sam_oneshot_s
                                        * the callback */
 #ifdef CONFIG_SAMA5_FREERUN
   volatile uint32_t start_count;      /* Stores the value of the freerun counter,
-                                       * at each start of the onshot timer. Is neccesary
+                                       * at each start of the oneshot timer. Is necessary
-                                       * to find out if the onshot counter was updated
+                                       * to find out if the oneshot counter was updated
                                        * correctly at the time of the call to
                                        * sam_oneshot_cancel or not. */
 #endif

arch/arm/src/samv7/sam_oneshot.h

@@ -84,8 +84,8 @@ struct sam_oneshot_s
                                        * the callback */
 #ifdef CONFIG_SAMV7_FREERUN
   volatile uint32_t start_count;      /* Stores the value of the freerun counter,
-                                       * at each start of the onshot timer. Is neccesary
+                                       * at each start of the oneshot timer. Is necessary
-                                       * to find out if the onshot counter was updated
+                                       * to find out if the oneshot counter was updated
                                        * correctly at the time of the call to
                                        * sam_oneshot_cancel or not. */
 #endif

arch/arm/src/stm32/stm32_sdio.c

@@ -93,7 +93,7 @@
  *   CONFIG_STM32_SDIO_WIDTH_D1_ONLY - This may be selected to force the
  *     driver operate with only a single data line (the default is to use
  *     all 4 SD data lines).
- *   CONFIG_SDM_DMAPRIO - SDIO DMA priority.  This can be selecte if
+ *   CONFIG_SDM_DMAPRIO - SDIO DMA priority.  This can be selected if
  *     CONFIG_STM32_SDIO_DMA is enabled.
  *   CONFIG_SDIO_XFRDEBUG - Enables some very low-level debug output
  *     This also requires CONFIG_DEBUG_FS and CONFIG_DEBUG_INFO
@@ -1468,7 +1468,7 @@ static int stm32_interrupt(int irq, void *context, FAR void *arg)
                       stm32_endtransfer(priv, SDIOWAIT_TRANSFERDONE);
                     }
 
-                  /* Otherwise, just disable futher transfer interrupts and
+                  /* Otherwise, just disable further transfer interrupts and
                    * wait for the DMA complete event.
                    */
 

arch/arm/src/stm32f7/stm32_sdmmc.c

@@ -95,7 +95,7 @@
  *   CONFIG_SDMMC1/2_WIDTH_D1_ONLY - This may be selected to force the driver
  *     operate with only a single data line (the default is to use all
  *     4 SD data lines).
- *   CONFIG_SDMMMC_DMAPRIO - SDMMC DMA priority.  This can be selecte if
+ *   CONFIG_SDMMC_DMAPRIO - SDMMC DMA priority.  This can be selected if
  *     CONFIG_STM32F7_SDMMC_DMA is enabled.
  *   CONFIG_CONFIG_STM32F7_SDMMC_XFRDEBUG - Enables some very low-level debug
  *     output.  This also requires CONFIG_DEBUG_FS and CONFIG_DEBUG_INFO
@@ -1723,7 +1723,7 @@ static int stm32_sdmmc_interrupt(int irq, void *context, void *arg)
                       stm32_endtransfer(priv, SDIOWAIT_TRANSFERDONE);
                     }
 
-                  /* Otherwise, just disable futher transfer interrupts and
+                  /* Otherwise, just disable further transfer interrupts and
                    * wait for the DMA complete event.
                    */
 

arch/arm/src/stm32l4/stm32l4_sdmmc.c

@@ -94,7 +94,7 @@
  *   CONFIG_SDMMC1/2_WIDTH_D1_ONLY - This may be selected to force the driver
  *     operate with only a single data line (the default is to use all
  *     4 SD data lines).
- *   CONFIG_SDMMMC_DMAPRIO - SDMMC DMA priority.  This can be selecte if
+ *   CONFIG_SDMMC_DMAPRIO - SDMMC DMA priority.  This can be selected if
  *     CONFIG_STM32L4_SDMMC_DMA is enabled.
  *   CONFIG_CONFIG_STM32L4_SDMMC_XFRDEBUG - Enables some very low-level
  *     debug output.  This also requires CONFIG_DEBUG_FS and
@@ -1575,7 +1575,7 @@ static int stm32_sdmmc_interrupt(int irq, void *context, void *arg)
                       stm32_endtransfer(priv, SDIOWAIT_TRANSFERDONE);
                     }
 
-                  /* Otherwise, just disable futher transfer interrupts and
+                  /* Otherwise, just disable further transfer interrupts and
                    * wait for the DMA complete event.
                    */
 

arch/arm/src/tms570/tms570_selftest.c

@@ -242,7 +242,7 @@ void tms570_memtest_selftest(void)
  * Name: tms570_memtest_start
  *
  * Description:
- *   Start the memory test on the selecte set of RAMs.  This test does not
+ *   Start the memory test on the selected set of RAMs.  This test does not
  *   return until the memory test is completed.
  *
  * Input Parameters:

arch/arm/src/xmc4/xmc4_timerisr.c

@@ -140,7 +140,7 @@ void arm_timer_initialize(void)
   putreg32(regval, NVIC_SYSH12_15_PRIORITY);
 
 #ifndef USE_STDBY_CLOCK
-  /* Note that is should not be neccesary to set the SYSTICK clock source:
+  /* Note that it should not be necessary to set the SYSTICK clock source:
    * "The CLKSOURCE bit in SysTick Control and Status register is always set
    *  to select the core clock."
    *

arch/mips/src/pic32mz/pic32mz-ethernet.c

@@ -179,8 +179,8 @@
 
 /* Debug Configuration *****************************************************/
 
-/* Register/Descriptor debug -- can only happen of CONFIG_DEBUG_FEATURES is
+/* Register/Descriptor debug -- can only happen if CONFIG_DEBUG_FEATURES is
- * selecte. This will probably generate much more output than you care to see.
+ * selected. This will probably generate much more output than you care to see.
  */
 
 #ifndef CONFIG_DEBUG_FEATURES

boards/arm/imx6/sabre-6quad/README.txt

@@ -574,9 +574,9 @@ A: Yes with the following modifications to the procedure above.
        gdb> mon go
 
    That will restart U-Boot and you have to press ENTER in the terminal
-   window to stop U-Boot.  Restarting U-Boot is a necesary part of the
+   window to stop U-Boot.  Restarting U-Boot is a necessary part of the
    restart process because you need to put the hardware back in its initial
-   state before running NuttX
+   state before running NuttX.
 
    Then this will restart the debug session just as before:
 

boards/arm/samv7/samv71-xult/README.txt

@@ -144,9 +144,9 @@ to a particular configuration.
      as of this writing. See discussion in include/nuttx/spi/slave.h and
      in the section entitle "SPI Slave" below.
 
-  9. A QSPI FLASH driver was added and verifed on 2015-11-10.  This driver
+  9. A QSPI FLASH driver was added and verified on 2015-11-10.  This driver
      operated in the memory mapped Serial Memory Mode (SMM).  See the
-     "S25FL116K QuadSPI FLASH" section below for futher information.
+     "S25FL116K QuadSPI FLASH" section below for further information.
 
  10. On-chip FLASH support as added and verified on 2015-11-13.  See the
      "Program FLASH Access" section below for further information.
@@ -174,7 +174,7 @@ use either the VCOM or an external RS-232 driver.  Here are some options.
     ------ ------ ------- ------- --------
 
     In this configuration, an external RS232 driver can also be used
-    instead of the shield.  Simply connext as follows:
+    instead of the shield.  Simply connect as follows:
 
     --------- -----------
     Arduino   RS-232
@@ -489,7 +489,7 @@ The configuration data device will appear at /dev/config.
 S25FL116K QuadSPI FLASH
 ====================
 
-A QSPI FLASH driver was added and verifed on 2015-11-07.  This driver
+A QSPI FLASH driver was added and verified on 2015-11-07.  This driver
 operated in the memory mapped Serial Memory Mode (SMM).  These
 configuration options were enabled to test QSPI:
 
@@ -575,7 +575,7 @@ wrapped as a character driver and available as /dev/mtd0.
 
 Program FLASH Access
 ====================
-An on-chip FLASH driver was added and verifed on 2015-11-13.  These
+An on-chip FLASH driver was added and verified on 2015-11-13.  These
 configuration options were enabled to test the on-chip FLASH support:
 
   CONFIG_MTD_PROGMEM=y
@@ -767,9 +767,9 @@ Cache-Related Issues
 
 I- and D-Caches can be enabled but the D-Cache must be enabled in write-
 through mode.  This is to work around issues with the RX and TX descriptors
-with are 8-bytes in size.  But the D-Cache cache line size is 32-bytes.
+which are 8-bytes in size.  But the D-Cache cache line size is 32-bytes.
 That means that you cannot reload, clean or invalidate a descriptor without
-also effecting three neighboring descriptors. Setting write through mode
+also affecting three neighboring descriptors.  Setting write through mode
 eliminates the need for cleaning the D-Cache.  If only reloading and
 invalidating are done, then there is no problem.
 
@@ -1191,7 +1191,7 @@ the connectors worked.  Let me share this so that, perhaps, I can save you
 the same embarrassment:
 
 - The maXTouch Xplained Pro has an Omron XF2M-5015-1A connector.  There is a
-  black bar at back (toward the baord).  Raise that bar and insert the cable
+  black bar at back (toward the board).  Raise that bar and insert the cable
   with the contacts away from the board.  Lower that bar to lock the cable
   in place.
 

boards/z80/ez80/ez80f910200zco/README.txt

@@ -62,7 +62,7 @@ Version 5.2.1
 
 Version 5.3.0
 
-  I verifed compilation using 5.30 on June 2, 2019.  To use this version,
+  I verified compilation using 5.30 on June 2, 2019.  To use this version,
   I had to make spurious modification to the implementation of gmtimer() to
   work around an internal compiler error.  I have still not verified that
   are no errors in the compiled code.

drivers/input/ft5x06.c

@@ -9,7 +9,7 @@
  *   Dec. 18, 2012
  *
  * Some of this driver was developed with input from NXP sample code for
- * the LPCXpresso-LPC54628 baord.  That sample code as a compatible BSD
+ * the LPCXpresso-LPC54628 board.  That sample code as a compatible BSD
  * license:
  *
  *   Copyright (c) 2016, Freescale Semiconductor, Inc.

drivers/input/ft5x06.h

@@ -9,7 +9,7 @@
  *   Dec. 18, 2012
  *
  * Some of this driver was developed with input from NXP sample code for
- * the LPCXpresso-LPC54628 baord.  That sample code as a compatible BSD
+ * the LPCXpresso-LPC54628 board.  That sample code as a compatible BSD
  * license:
  *
  *   Copyright (c) 2016, Freescale Semiconductor, Inc.

drivers/net/telnet.c

@@ -628,7 +628,7 @@ static bool telnet_putchar(FAR struct telnet_dev_s *priv, uint8_t ch,
   register int index;
   bool ret = false;
 
-  /* Ignore carriage returns (we will put these in automatically as necesary) */
+  /* Ignore carriage returns (we will put these in automatically as necessary) */
 
   if (ch != ISO_cr)
     {

fs/nxffs/nxffs.h

@@ -955,7 +955,7 @@ int nxffs_wrreserve(FAR struct nxffs_volume_s *volume, size_t size);
  *
  * Input Parameters:
  *   volume - Describes the NXFFS volume
- *   size - The size of the object to be verifed.
+ *   size - The size of the object to be verified.
  *
  * Returned Value:
  *   Zero is returned on success.  Otherwise, a negated errno value is

fs/nxffs/nxffs_write.c

@@ -835,7 +835,7 @@ int nxffs_wrreserve(FAR struct nxffs_volume_s *volume, size_t size)
  *
  * Input Parameters:
  *   volume - Describes the NXFFS volume
- *   size - The size of the object to be verifed.
+ *   size - The size of the object to be verified.
  *
  * Returned Value:
  *   Zero is returned on success.  Otherwise, a negated errno value is

include/nuttx/sched_note.h

@@ -310,7 +310,7 @@ void sched_note_spinabort(FAR struct tcb_s *tcb, FAR volatile void *spinlock);
  *
  * Description:
  *   Remove the next note from the tail of the circular buffer.  The note
- *   is also removed from the circular buffer to make room for futher notes.
+ *   is also removed from the circular buffer to make room for further notes.
  *
  * Input Parameters:
  *   buffer - Location to return the next note

net/icmp/icmp_sendto.c

@@ -410,7 +410,7 @@ ssize_t icmp_sendto(FAR struct socket *psock, FAR const void *buf, size_t len,
    * packets from the read-ahead buffer.
    *
    * REVISIT:  How to we free up any lingering reponses if there are no
-   * futher pings?
+   * further pings?
    */
 
   icmp = (FAR struct icmp_hdr_s *)buf;

net/icmpv6/icmpv6_sendto.c

@@ -401,7 +401,7 @@ ssize_t icmpv6_sendto(FAR struct socket *psock, FAR const void *buf, size_t len,
    * packets from the read-ahead buffer.
    *
    * REVISIT:  How to we free up any lingering reponses if there are no
-   * futher pings?
+   * further pings?
    */
 
   icmpv6 = (FAR struct icmpv6_echo_request_s *)buf;

sched/sched/sched_note.c

@@ -594,7 +594,7 @@ void sched_note_spinabort(FAR struct tcb_s *tcb, FAR volatile void *spinlock)
  *
  * Description:
  *   Remove the next note from the tail of the circular buffer.  The note
- *   is also removed from the circular buffer to make room for futher notes.
+ *   is also removed from the circular buffer to make room for further notes.
  *
  * Input Parameters:
  *   buffer - Location to return the next note

tools/Makefile.host

@@ -182,7 +182,7 @@ nxstyle: nxstyle$(HOSTEXEEXT)
 endif
 
 # initialconfig - Create a barebones .config file sufficient only for
-# instantiating the symbolic links necesary to do a real configuration
+# instantiating the symbolic links necessary to do a real configuration
 # from scratch.
 
 initialconfig$(HOSTEXEEXT): initialconfig.c