mirror of
https://github.com/apache/nuttx.git
synced 2026-06-04 06:42:32 +08:00
Remove documentation from defconfig files so that they are more maintainable
git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@5068 42af7a65-404d-4744-a932-0658087f49c3
This commit is contained in:
patacongo
@@ -33,39 +33,7 @@
|
||||
#
|
||||
############################################################################
|
||||
#
|
||||
# architecture selection
|
||||
#
|
||||
# CONFIG_ARCH - identifies the arch subdirectory and, hence, the
|
||||
# processor architecture.
|
||||
# CONFIG_ARCH_family - for use in C code. This identifies the
|
||||
# particular chip family that the architecture is implemented
|
||||
# in.
|
||||
# CONFIG_ARCH_architecture - for use in C code. This identifies the
|
||||
# specific architecture within the chip familyl.
|
||||
# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
||||
# CONFIG_ARCH_CHIP_name - For use in C code
|
||||
# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
|
||||
# the board that supports the particular chip or SoC.
|
||||
# CONFIG_ARCH_BOARD_name - for use in C code
|
||||
# CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
|
||||
# CONFIG_BOARD_LOOPSPERMSEC - for delay loops
|
||||
# CONFIG_DRAM_SIZE - Describes the installed DRAM.
|
||||
# CONFIG_DRAM_START - The start address of DRAM (physical)
|
||||
# CONFIG_ARCH_IRQPRIO - The LM3S6918 supports interrupt prioritization
|
||||
# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
||||
# stack. If defined, this symbol is the size of the interrupt
|
||||
# stack in bytes. If not defined, the user task stacks will be
|
||||
# used during interrupt handling.
|
||||
# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
||||
# CONFIG_ARCH_BOOTLOADER - Configure to use the MicroMint Eagle-100
|
||||
# Ethernet bootloader.
|
||||
# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
||||
# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
||||
# cause a 100 second delay during boot-up. This 100 second delay
|
||||
# serves no purpose other than it allows you to calibratre
|
||||
# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure
|
||||
# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until
|
||||
# the delay actually is 100 seconds.
|
||||
# Architecture Selection
|
||||
#
|
||||
CONFIG_ARCH="arm"
|
||||
CONFIG_ARCH_ARM=y
|
||||
@@ -101,19 +69,6 @@ CONFIG_LM3S_DISABLE_GPIOJ_IRQS=y
|
||||
#
|
||||
# LM3S6918 specific serial device driver settings
|
||||
#
|
||||
# CONFIG_UARTn_DISABLE - select to disable all support for
|
||||
# the UART
|
||||
# CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
|
||||
# console and ttys0 (default is the UART0).
|
||||
# CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
|
||||
# This specific the size of the receive buffer
|
||||
# CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
|
||||
# being sent. This specific the size of the transmit buffer
|
||||
# CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be
|
||||
# CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
|
||||
# CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
||||
# CONFIG_UARTn_2STOP - Two stop bits
|
||||
#
|
||||
CONFIG_UART0_DISABLE=n
|
||||
CONFIG_UART1_DISABLE=y
|
||||
CONFIG_UART0_SERIAL_CONSOLE=y
|
||||
@@ -134,16 +89,6 @@ CONFIG_UART1_2STOP=0
|
||||
#
|
||||
# LM3S6918 specific SSI device driver settings
|
||||
#
|
||||
# CONFIG_SSIn_DISABLE - select to disable all support for
|
||||
# the SSI
|
||||
# CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support
|
||||
# Poll-waiting is recommended if the interrupt rate would be to
|
||||
# high in the interrupt driven case.
|
||||
# CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
|
||||
# emptying the Rx FIFO. If the SPI frequency is high and this
|
||||
# value is large, then larger values of this setting may cause
|
||||
# Rx FIFO overrun errors. Default: half of the Tx FIFO size (4).
|
||||
#
|
||||
CONFIG_SSI0_DISABLE=n
|
||||
CONFIG_SSI1_DISABLE=y
|
||||
CONFIG_SSI_POLLWAIT=y
|
||||
@@ -152,19 +97,6 @@ CONFIG_SSI_POLLWAIT=y
|
||||
#
|
||||
# LM3S6918 specific serial device driver settings
|
||||
#
|
||||
# CONFIG_LM3S_ETHERNET - This must be set (along with CONFIG_NET)
|
||||
# to build the LM3S Ethernet driver
|
||||
# CONFIG_LM3S_ETHLEDS - Enable to use Ethernet LEDs on the board.
|
||||
# CONFIG_LM3S_BOARDMAC - If the board-specific logic can provide
|
||||
# a MAC address (via lm3s_ethernetmac()), then this should be selected.
|
||||
# CONFIG_LM3S_ETHHDUPLEX - Set to force half duplex operation
|
||||
# CONFIG_LM3S_ETHNOAUTOCRC - Set to suppress auto-CRC generation
|
||||
# CONFIG_LM3S_ETHNOPAD - Set to suppress Tx padding
|
||||
# CONFIG_LM3S_MULTICAST - Set to enable multicast frames
|
||||
# CONFIG_LM3S_PROMISCUOUS - Set to enable promiscuous mode
|
||||
# CONFIG_LM3S_BADCRC - Set to enable bad CRC rejection.
|
||||
# CONFIG_LM3S_DUMPPACKET - Dump each packet received/sent to the console.
|
||||
#
|
||||
CONFIG_LM3S_ETHERNET=y
|
||||
CONFIG_LM3S_ETHLEDS=n
|
||||
CONFIG_LM3S_BOARDMAC=y
|
||||
@@ -179,19 +111,6 @@ CONFIG_LM3S_DUMPPACKET=n
|
||||
#
|
||||
# General build options
|
||||
#
|
||||
# CONFIG_RRLOAD_BINARY - make the rrload binary format used with
|
||||
# BSPs from www.ridgerun.com using the tools/mkimage.sh script
|
||||
# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format
|
||||
# used with many different loaders using the GNU objcopy program
|
||||
# Should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format
|
||||
# used with many different loaders using the GNU objcopy program
|
||||
# Should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_RAW_BINARY - make a raw binary format file used with many
|
||||
# different loaders using the GNU objcopy program. This option
|
||||
# should not be selected if you are not using the GNU toolchain.
|
||||
# CONFIG_HAVE_LIBM - toolchain supports libm.a
|
||||
#
|
||||
CONFIG_RRLOAD_BINARY=n
|
||||
CONFIG_INTELHEX_BINARY=n
|
||||
CONFIG_MOTOROLA_SREC=n
|
||||
@@ -201,72 +120,6 @@ CONFIG_HAVE_LIBM=n
|
||||
#
|
||||
# General OS setup
|
||||
#
|
||||
# CONFIG_APPS_DIR - Identifies the relative path to the directory
|
||||
# that builds the application to link with NuttX. Default: ../apps
|
||||
# CONFIG_DEBUG - enables built-in debug options
|
||||
# CONFIG_DEBUG_VERBOSE - enables verbose debug output
|
||||
# CONFIG_DEBUG_SYMBOLS - build without optimization and with
|
||||
# debug symbols (needed for use with a debugger).
|
||||
# CONFIG_MM_REGIONS - If the architecture includes multiple
|
||||
# regions of memory to allocate from, this specifies the
|
||||
# number of memory regions that the memory manager must
|
||||
# handle and enables the API mm_addregion(start, end);
|
||||
# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot
|
||||
# time console output
|
||||
# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz
|
||||
# or MSEC_PER_TICK=10. This setting may be defined to
|
||||
# inform NuttX that the processor hardware is providing
|
||||
# system timer interrupts at some interrupt interval other
|
||||
# than 10 msec.
|
||||
# CONFIG_RR_INTERVAL - The round robin timeslice will be set
|
||||
# this number of milliseconds; Round robin scheduling can
|
||||
# be disabled by setting this value to zero.
|
||||
# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in
|
||||
# scheduler to monitor system performance
|
||||
# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a
|
||||
# task name to save in the TCB. Useful if scheduler
|
||||
# instrumentation is selected. Set to zero to disable.
|
||||
# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY -
|
||||
# Used to initialize the internal time logic.
|
||||
# CONFIG_JULIAN_TIME - Enables Julian time conversions
|
||||
# CONFIG_DEV_CONSOLE - Set if architecture-specific logic
|
||||
# provides /dev/console. Enables stdout, stderr, stdin.
|
||||
# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console
|
||||
# driver (minimul support)
|
||||
# CONFIG_MUTEX_TYPES: Set to enable support for recursive and
|
||||
# errorcheck mutexes. Enables pthread_mutexattr_settype().
|
||||
# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority
|
||||
# inheritance on mutexes and semaphores.
|
||||
# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority
|
||||
# inheritance is enabled. It defines the maximum number of
|
||||
# different threads (minus one) that can take counts on a
|
||||
# semaphore with priority inheritance support. This may be
|
||||
# set to zero if priority inheritance is disabled OR if you
|
||||
# are only using semaphores as mutexes (only one holder) OR
|
||||
# if no more than two threads participate using a counting
|
||||
# semaphore.
|
||||
# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled,
|
||||
# then this setting is the maximum number of higher priority
|
||||
# threads (minus 1) than can be waiting for another thread
|
||||
# to release a count on a semaphore. This value may be set
|
||||
# to zero if no more than one thread is expected to wait for
|
||||
# a semaphore.
|
||||
# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors
|
||||
# by task_create() when a new task is started. If set, all
|
||||
# files/drivers will appear to be closed in the new task.
|
||||
# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first
|
||||
# three file descriptors (stdin, stdout, stderr) by task_create()
|
||||
# when a new task is started. If set, all files/drivers will
|
||||
# appear to be closed in the new task except for stdin, stdout,
|
||||
# and stderr.
|
||||
# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket
|
||||
# desciptors by task_create() when a new task is started. If
|
||||
# set, all sockets will appear to be closed in the new task.
|
||||
# CONFIG_NXFLAT. Enable support for the NXFLAT binary format.
|
||||
# This format will support execution of NuttX binaries located
|
||||
# in a ROMFS filesystem (see examples/nxflat).
|
||||
#
|
||||
#CONFIG_APPS_DIR=
|
||||
CONFIG_DEBUG=y
|
||||
CONFIG_DEBUG_VERBOSE=n
|
||||
CONFIG_DEBUG_SYMBOLS=n
|
||||
@@ -318,9 +171,6 @@ CONFIG_DISABLE_POLL=y
|
||||
#
|
||||
# Misc libc settings
|
||||
#
|
||||
# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a
|
||||
# little smaller if we do not support fieldwidthes
|
||||
#
|
||||
CONFIG_NOPRINTF_FIELDWIDTH=n
|
||||
|
||||
#
|
||||
@@ -343,38 +193,6 @@ CONFIG_ARCH_BZERO=n
|
||||
#
|
||||
# Sizes of configurable things (0 disables)
|
||||
#
|
||||
# CONFIG_MAX_TASKS - The maximum number of simultaneously
|
||||
# active tasks. This value must be a power of two.
|
||||
# CONFIG_MAX_TASK_ARGS - This controls the maximum number of
|
||||
# of parameters that a task may receive (i.e., maxmum value
|
||||
# of 'argc')
|
||||
# CONFIG_NPTHREAD_KEYS - The number of items of thread-
|
||||
# specific data that can be retained
|
||||
# CONFIG_NFILE_DESCRIPTORS - The maximum number of file
|
||||
# descriptors (one for each open)
|
||||
# CONFIG_NFILE_STREAMS - The maximum number of streams that
|
||||
# can be fopen'ed
|
||||
# CONFIG_NAME_MAX - The maximum size of a file name.
|
||||
# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate
|
||||
# on fopen. (Only if CONFIG_NFILE_STREAMS > 0)
|
||||
# CONFIG_NUNGET_CHARS - Number of characters that can be
|
||||
# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0)
|
||||
# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message
|
||||
# structures. The system manages a pool of preallocated
|
||||
# message structures to minimize dynamic allocations
|
||||
# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with
|
||||
# a fixed payload size given by this settin (does not include
|
||||
# other message structure overhead.
|
||||
# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that
|
||||
# can be passed to a watchdog handler
|
||||
# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog
|
||||
# structures. The system manages a pool of preallocated
|
||||
# watchdog structures to minimize dynamic allocations
|
||||
# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX
|
||||
# timer structures. The system manages a pool of preallocated
|
||||
# timer structures to minimize dynamic allocations. Set to
|
||||
# zero for all dynamic allocations.
|
||||
#
|
||||
CONFIG_MAX_TASKS=8
|
||||
CONFIG_MAX_TASK_ARGS=4
|
||||
CONFIG_NPTHREAD_KEYS=0
|
||||
@@ -392,51 +210,18 @@ CONFIG_PREALLOC_TIMERS=8
|
||||
#
|
||||
# Filesystem configuration
|
||||
#
|
||||
# CONFIG_FS_FAT - Enable FAT filesystem support
|
||||
# CONFIG_FAT_SECTORSIZE - Max supported sector size
|
||||
# CONFIG_FS_ROMFS - Enable ROMFS filesystem support
|
||||
CONFIG_FS_FAT=n
|
||||
CONFIG_FS_ROMFS=n
|
||||
|
||||
#
|
||||
# SPI-based MMC/SD driver
|
||||
#
|
||||
# CONFIG_MMCSD_NSLOTS
|
||||
# Number of MMC/SD slots supported by the driver
|
||||
# CONFIG_MMCSD_READONLY
|
||||
# Provide read-only access (default is read/write)
|
||||
# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card.
|
||||
# Default is 20MHz.
|
||||
#
|
||||
CONFIG_MMCSD_NSLOTS=1
|
||||
CONFIG_MMCSD_READONLY=n
|
||||
CONFIG_MMCSD_SPICLOCK=12500000
|
||||
|
||||
#
|
||||
# TCP/IP and UDP support via uIP
|
||||
# CONFIG_NET - Enable or disable all network features
|
||||
# CONFIG_NET_IPv6 - Build in support for IPv6
|
||||
# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread.
|
||||
# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options
|
||||
# CONFIG_NET_BUFSIZE - uIP buffer size
|
||||
# CONFIG_NET_TCP - TCP support on or off
|
||||
# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks)
|
||||
# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers
|
||||
# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero)
|
||||
# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until
|
||||
# accept() is called. The size of the backlog is selected when listen() is called.
|
||||
# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks)
|
||||
# CONFIG_NET_UDP - UDP support on or off
|
||||
# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off
|
||||
# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections
|
||||
# CONFIG_NET_ICMP - ICMP ping response support on or off
|
||||
# CONFIG_NET_ICMP_PING - ICMP ping request support on or off
|
||||
# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address
|
||||
# CONFIG_NET_STATISTICS - uIP statistics on or off
|
||||
# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window
|
||||
# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table
|
||||
# CONFIG_NET_BROADCAST - Broadcast support
|
||||
# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates
|
||||
#
|
||||
CONFIG_NET=y
|
||||
CONFIG_NET_IPv6=n
|
||||
@@ -462,8 +247,6 @@ CONFIG_NET_BROADCAST=n
|
||||
|
||||
#
|
||||
# UIP Network Utilities
|
||||
# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP
|
||||
# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries
|
||||
#
|
||||
CONFIG_NET_DHCP_LIGHT=n
|
||||
CONFIG_NET_RESOLV_ENTRIES=4
|
||||
@@ -478,18 +261,7 @@ CONFIG_EXAMPLE_UIP_DHCPC=n
|
||||
|
||||
#
|
||||
# Settings for examples/nettest
|
||||
# CONFIG_EXAMPLE_NETTEST_SERVER - The target board can act
|
||||
# as either the client side or server side of the test
|
||||
# CONFIG_EXAMPLE_NETTEST_PERFORMANCE - If set, then the
|
||||
# client side simply receives messages forever, allowing
|
||||
# measurement of throughput
|
||||
# CONFIG_EXAMPLE_NETTEST_NOMAC - Set if the hardware has
|
||||
# no MAC address; one will be assigned
|
||||
# CONFIG_EXAMPLE_NETTEST_IPADDR - Target board IP address
|
||||
# CONFIG_EXAMPLE_NETTEST_DRIPADDR - Default router address
|
||||
# CONFIG_EXAMPLE_NETTEST_NETMASK - Network mask
|
||||
# CONFIG_EXAMPLE_NETTEST_CLIENTIP - IP address of the
|
||||
# client side of the test (may be target or host)
|
||||
#
|
||||
CONFIG_EXAMPLE_NETTEST_SERVER=n
|
||||
CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n
|
||||
CONFIG_EXAMPLE_NETTEST_NOMAC=n
|
||||
@@ -508,36 +280,6 @@ CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
|
||||
#
|
||||
# Settings for apps/nshlib
|
||||
#
|
||||
# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer
|
||||
# CONFIG_NSH_STRERROR - Use strerror(errno)
|
||||
# CONFIG_NSH_LINELEN - Maximum length of one command line
|
||||
# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi
|
||||
# CONFIG_NSH_DISABLESCRIPT - Disable scripting support
|
||||
# CONFIG_NSH_DISABLEBG - Disable background commands
|
||||
# CONFIG_NSH_ROMFSETC - Use startup script in /etc
|
||||
# CONFIG_NSH_CONSOLE - Use serial console front end
|
||||
# CONFIG_NSH_TELNET - Use telnetd console front end
|
||||
# CONFIG_NSH_ARCHINIT - Platform provides architecture
|
||||
# specific initialization (nsh_archinitialize()).
|
||||
#
|
||||
# If CONFIG_NSH_TELNET is selected:
|
||||
# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size
|
||||
# CONFIG_NSH_DHCPC - Obtain address using DHCP
|
||||
# CONFIG_NSH_IPADDR - Provides static IP address
|
||||
# CONFIG_NSH_DRIPADDR - Provides static router IP address
|
||||
# CONFIG_NSH_NETMASK - Provides static network mask
|
||||
# CONFIG_NSH_NOMAC - Use a bogus MAC address
|
||||
#
|
||||
# If CONFIG_NSH_ROMFSETC is selected:
|
||||
# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint
|
||||
# CONFIG_NSH_INITSCRIPT - Relative path to init script
|
||||
# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor
|
||||
# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size
|
||||
# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor
|
||||
# CONFIG_NSH_FATSECTSIZE - FAT FS sector size
|
||||
# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors
|
||||
# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint
|
||||
#
|
||||
CONFIG_NSH_FILEIOSIZE=512
|
||||
CONFIG_NSH_STRERROR=n
|
||||
CONFIG_NSH_LINELEN=64
|
||||
@@ -573,26 +315,6 @@ CONFIG_NSH_MMCSDMINOR=0
|
||||
#
|
||||
# Stack and heap information
|
||||
#
|
||||
# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP
|
||||
# operation from FLASH but must copy initialized .data sections to RAM.
|
||||
# (should also be =n for the Eagle100 which always runs from flash)
|
||||
# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH
|
||||
# but copy themselves entirely into RAM for better performance.
|
||||
# CONFIG_CUSTOM_STACK - The up_ implementation will handle
|
||||
# all stack operations outside of the nuttx model.
|
||||
# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only)
|
||||
# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack.
|
||||
# This is the thread that (1) performs the inital boot of the system up
|
||||
# to the point where user_start() is spawned, and (2) there after is the
|
||||
# IDLE thread that executes only when there is no other thread ready to
|
||||
# run.
|
||||
# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate
|
||||
# for the main user thread that begins at the user_start() entry point.
|
||||
# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size
|
||||
# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size
|
||||
# CONFIG_HEAP_BASE - The beginning of the heap
|
||||
# CONFIG_HEAP_SIZE - The size of the heap
|
||||
#
|
||||
CONFIG_BOOT_RUNFROMFLASH=n
|
||||
CONFIG_BOOT_COPYTORAM=n
|
||||
CONFIG_CUSTOM_STACK=n
|
||||
|
||||
Reference in New Issue
Block a user