SAM4E-EK: Add a touchscreen driver (untestd on initial checkin)

configs/sam4e-ek/Kconfig

@@ -70,15 +70,12 @@ choice
 
 config SAM4EEK_LCD_RGB565
 	bool "RGB565"
-	default n
 
 config SAM4EEK_LCD_RGB24
 	bool "RGB24 / RGB888"
-	default n
 
 config SAM4EEK_LCD_RGB32
 	bool "RGB32"
-	default n
 
 endchoice # ILI9325-based LCD Color Configuration
 

configs/sam4e-ek/README.txt

@@ -857,8 +857,8 @@ Touchscreen
       CONFIG_SPI_OWNBUS=y                   : Smaller code if this is the only SPI device
 
       CONFIG_INPUT=y                        : Enable support for input devices
-      CONFIG_INPUT_ADS7843E=y               : Enable support for the XPT2046
+      CONFIG_INPUT_ADS7843E=y               : Enable support for the ADS7843E
-      CONFIG_ADS7843E_SPIDEV=2              : Use SPI CS 2 for communication
+      CONFIG_ADS7843E_SPIDEV=0              : Use SPI CS 0 for communication
       CONFIG_ADS7843E_SPIMODE=0             : Use SPI mode 0
       CONFIG_ADS7843E_FREQUENCY=1000000     : SPI BAUD 1MHz
       CONFIG_ADS7843E_SWAPXY=y              : If landscape orientation
@@ -889,9 +889,6 @@ Touchscreen
       CONFIG_DEBUG_VERBOSE=y            : Enable verbose debug output
       CONFIG_DEBUG_INPUT=y              : Enable debug output from input devices
 
-  STATUS
-    2014-3-27: As of this writing, the touchscreen is untested.
-
 ILI9325-Based LCD
 =================
 
@@ -1335,6 +1332,96 @@ Configurations
        slot.  Support for the SD slot can be enabled following the
        instructions provided above in the paragraph entitled "HSMCI."
 
+   11. This configuration has been used for verifying the touchscreen on
+       on the SAM4E-EK LCD module.
+
+       The NSH configuration can be used to verify the ADS7843E touchscreen on
+       the SAM4E-EK LCD.  With these modifications, you can include the touchscreen
+       test program at apps/examples/touchscreen as an NSH built-in application.
+       You can enable the touchscreen and test by modifying the default
+       configuration in the following ways:
+
+       Device Drivers
+         CONFIG_SPI=y                      : Enable SPI support
+         CONFIG_SPI_EXCHANGE=y             : The exchange() method is supported
+         CONFIG_SPI_OWNBUS=y               : Smaller code if this is the only SPI device
+
+         CONFIG_INPUT=y                    : Enable support for input devices
+         CONFIG_INPUT_ADS7843E=y           : Enable support for the ADS7843E
+         CONFIG_ADS7843E_SPIDEV=0          : Use SPI CS 0 for communication
+         CONFIG_ADS7843E_SPIMODE=0         : Use SPI mode 0
+         CONFIG_ADS7843E_FREQUENCY=1000000 : SPI BAUD 1MHz
+         CONFIG_ADS7843E_SWAPXY=y          : If landscape orientation
+         CONFIG_ADS7843E_THRESHX=51        : These will probably need to be tuned
+         CONFIG_ADS7843E_THRESHY=39
+
+       System Type -> Peripherals:
+         CONFIG_SAM34_SPI0=y               : Enable support for SPI
+
+       System Type:
+         CONFIG_SAM34_GPIO_IRQ=y           : GPIO interrupt support
+         CONFIG_SAM34_GPIOA_IRQ=y          : Enable GPIO interrupts from port A
+
+       RTOS Features:
+         CONFIG_DISABLE_SIGNALS=n          : Signals are required
+
+       Library Support:
+         CONFIG_SCHED_WORKQUEUE=y          : Work queue support required
+
+       Application Configuration:
+         CONFIG_EXAMPLES_TOUCHSCREEN=y     : Enable the touchscreen built-in test
+
+       Defaults should be okay for related touchscreen settings.  Touchscreen
+       debug output on UART0 can be enabled with:
+
+       Build Setup:
+         CONFIG_DEBUG=y                    : Enable debug features
+         CONFIG_DEBUG_VERBOSE=y            : Enable verbose debug output
+         CONFIG_DEBUG_INPUT=y              : Enable debug output from input devices
+
+   11. This configuration can be re-configured to test the on-board LCD
+       module.
+
+       System Type -> AT91SAM3/4 Configuration Options
+         CONFIG_SAM34_SMC=y                : SMC support
+
+       Device Drivers -> LCD Driver Support
+         CONFIG_LCD=y                      : Enable LCD support
+         CONFIG_NX_LCDDRIVER=y             : LCD graphics device
+         CONFIG_LCD_MAXCONTRAST=1          : Value should not matter
+         CONFIG_LCD_MAXPOWER=64            : Must be > 16
+         CONFIG_LCD_LANDSCAPE=y            : Landscape orientation
+
+       Board Selection
+         CONFIG_SAM4EEK_LCD_RGB565=y       : Color resolution
+         CONFIG_SAM4EEK_LCD_BGCOLOR=0x00   : Initial background color
+
+       Graphics Support
+         CONFIG_NX=y
+
+       Graphics Support -> Supported Pixel Depths
+         CONFIG_NX_DISABLE_1BPP=y          : Only 16BPP supported
+         CONFIG_NX_DISABLE_2BPP=y
+         CONFIG_NX_DISABLE_4BPP=y
+         CONFIG_NX_DISABLE_8BPP=y
+         CONFIG_NX_DISABLE_24BPP=y
+         CONFIG_NX_DISABLE_32BPP=y
+
+       Graphics Support -> Font Selections
+         CONFIG_NXFONTS_CHARBITS=7
+         CONFIG_NXFONT_SANS22X29B=y
+         CONFIG_NXFONT_SANS23X27=y
+
+       Application Configuration -> Examples
+         CONFIG_EXAMPLES_NXLINES=y
+         CONFIG_EXAMPLES_NXLINES_BGCOLOR=0x0320
+         CONFIG_EXAMPLES_NXLINES_LINEWIDTH=16
+         CONFIG_EXAMPLES_NXLINES_LINECOLOR=0xffe0
+         CONFIG_EXAMPLES_NXLINES_BORDERWIDTH=4
+         CONFIG_EXAMPLES_NXLINES_BORDERCOLOR=0xffe0
+         CONFIG_EXAMPLES_NXLINES_CIRCLECOLOR=0xf7bb
+         CONFIG_EXAMPLES_NXLINES_BPP=16
+
        STATUS:
          2014-3-24:  DMA is not currently functional and without DMA, there
                      may not be reliable data transfers at high speeds due

configs/sam4e-ek/src/Makefile

@@ -46,10 +46,6 @@ ifeq ($(CONFIG_HAVE_CXXINITIALIZE),y)
 CSRCS += sam_cxxinitialize.c
 endif
 
-ifeq ($(CONFIG_SAM4EEK_ILI9325),y)
-CSRCS += sam_ili9325.c
-endif
-
 ifeq ($(CONFIG_NSH_ARCHINIT),y)
 CSRCS += sam_nsh.c
 endif
@@ -62,6 +58,10 @@ ifeq ($(CONFIG_LCD),y)
 CSRCS += sam_ili9325.c
 endif
 
+ifeq ($(CONFIG_INPUT_ADS7843E),y)
+CSRCS += sam_ads7843e.c
+endif
+
 ifeq ($(CONFIG_SAM34_SPI0),y)
 CSRCS += sam_spi.c
 ifeq ($(CONFIG_MTD_AT25),y)

configs/sam4e-ek/src/sam_ads7843e.c

@@ -0,0 +1,290 @@
+/************************************************************************************
+ * configs/sam4e-ek/src/sam_ads7843e.c
+ *
+ *   Copyright (C) 2014 Gregory Nutt. All rights reserved.
+ *   Author: Gregory Nutt <gnutt@nuttx.org>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name NuttX nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ************************************************************************************/
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <stdbool.h>
+#include <stdio.h>
+#include <debug.h>
+#include <assert.h>
+#include <errno.h>
+
+#include <nuttx/spi/spi.h>
+#include <nuttx/input/touchscreen.h>
+#include <nuttx/input/ads7843e.h>
+
+#include "sam_gpio.h"
+#include "sam4e-ek.h"
+
+#if defined(CONFIG_INPUT) && defined(CONFIG_INPUT_ADS7843E)
+
+/****************************************************************************
+ * Pre-Processor Definitions
+ ****************************************************************************/
+/* Configuration ************************************************************/
+
+#ifndef CONFIG_SAM34_SPI0
+#  error "Touchscreen support requires CONFIG_SAM34_SPI0"
+#endif
+
+#ifndef CONFIG_SAM34_GPIOA_IRQ
+#  error "Touchscreen support requires CONFIG_SAM34_GPIOA_IRQ"
+#endif
+
+#ifndef CONFIG_ADS7843E_FREQUENCY
+#  define CONFIG_ADS7843E_FREQUENCY 500000
+#endif
+
+#ifndef CONFIG_ADS7843E_SPIDEV
+#  define CONFIG_ADS7843E_SPIDEV TSC_CSNUM
+#endif
+
+#if CONFIG_ADS7843E_SPIDEV != TSC_CSNUM
+#  error "CONFIG_ADS7843E_SPIDEV must have the same value as TSC_CSNUM"
+#endif
+
+#ifndef CONFIG_ADS7843E_DEVMINOR
+#  define CONFIG_ADS7843E_DEVMINOR 0
+#endif
+
+/****************************************************************************
+ * Static Function Prototypes
+ ****************************************************************************/
+
+/* IRQ/GPIO access callbacks.  These operations all hidden behind
+ * callbacks to isolate the ADS7843E driver from differences in GPIO
+ * interrupt handling by varying boards and MCUs.  If possible,
+ * interrupts should be configured on both rising and falling edges
+ * so that contact and loss-of-contact events can be detected.
+ *
+ * attach  - Attach the ADS7843E interrupt handler to the GPIO interrupt
+ * enable  - Enable or disable the GPIO interrupt
+ * clear   - Acknowledge/clear any pending GPIO interrupt
+ * pendown - Return the state of the pen down GPIO input
+ */
+
+static int  tsc_attach(FAR struct ads7843e_config_s *state, xcpt_t isr);
+static void tsc_enable(FAR struct ads7843e_config_s *state, bool enable);
+static void tsc_clear(FAR struct ads7843e_config_s *state);
+static bool tsc_busy(FAR struct ads7843e_config_s *state);
+static bool tsc_pendown(FAR struct ads7843e_config_s *state);
+
+/****************************************************************************
+ * Private Data
+ ****************************************************************************/
+
+/* A reference to a structure of this type must be passed to the ADS7843E
+ * driver.  This structure provides information about the configuration
+ * of the ADS7843E and provides some board-specific hooks.
+ *
+ * Memory for this structure is provided by the caller.  It is not copied
+ * by the driver and is presumed to persist while the driver is active. The
+ * memory must be writeable because, under certain circumstances, the driver
+ * may modify frequency or X plate resistance values.
+ */
+
+static struct ads7843e_config_s g_tscinfo =
+{
+  .frequency = CONFIG_ADS7843E_FREQUENCY,
+
+  .attach    = tsc_attach,
+  .enable    = tsc_enable,
+  .clear     = tsc_clear,
+  .busy      = tsc_busy,
+  .pendown   = tsc_pendown,
+};
+
+/****************************************************************************
+ * Private Functions
+ ****************************************************************************/
+
+/* IRQ/GPIO access callbacks.  These operations all hidden behind
+ * callbacks to isolate the ADS7843E driver from differences in GPIO
+ * interrupt handling by varying boards and MCUs.  If possible,
+ * interrupts should be configured on both rising and falling edges
+ * so that contact and loss-of-contact events can be detected.
+ *
+ * attach  - Attach the ADS7843E interrupt handler to the GPIO interrupt
+ * enable  - Enable or disable the GPIO interrupt
+ * clear   - Acknowledge/clear any pending GPIO interrupt
+ * pendown - Return the state of the pen down GPIO input
+ */
+
+static int tsc_attach(FAR struct ads7843e_config_s *state, xcpt_t isr)
+{
+  /* Attach the ADS7843E interrupt */
+
+  ivdbg("Attaching %p to IRQ %d\n", isr, SAM_TCS_IRQ);
+  return irq_attach(SAM_TCS_IRQ, isr);
+}
+
+static void tsc_enable(FAR struct ads7843e_config_s *state, bool enable)
+{
+  /* Attach and enable, or detach and disable */
+
+  ivdbg("IRQ:%d enable:%d\n", SAM_TCS_IRQ, enable);
+  if (enable)
+    {
+      sam_gpioirqenable(SAM_TCS_IRQ);
+    }
+  else
+    {
+      sam_gpioirqdisable(SAM_TCS_IRQ);
+    }
+}
+
+static void tsc_clear(FAR struct ads7843e_config_s *state)
+{
+  /* Does nothing */
+}
+
+static bool tsc_busy(FAR struct ads7843e_config_s *state)
+{
+#if defined(CONFIG_DEBUG_INPUT) && defined(CONFIG_DEBUG_VERBOSE)
+  static bool last = (bool)-1;
+#endif
+
+  /* BUSY is high impedance when CS is high (not selected).  When CS is
+   * is low, BUSY is active high.
+   */
+
+  bool busy = sam_gpioread(GPIO_TCS_BUSY);
+#if defined(CONFIG_DEBUG_INPUT) && defined(CONFIG_DEBUG_VERBOSE)
+  if (busy != last)
+    {
+      ivdbg("busy:%d\n", busy);
+      last = busy;
+    }
+#endif
+
+  return busy;
+}
+
+static bool tsc_pendown(FAR struct ads7843e_config_s *state)
+{
+  /* The /PENIRQ value is active low */
+
+  bool pendown = !sam_gpioread(GPIO_TCS_IRQ);
+  ivdbg("pendown:%d\n", pendown);
+  return pendown;
+}
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/****************************************************************************
+ * Name: arch_tcinitialize
+ *
+ * Description:
+ *   Each board that supports a touchscreen device must provide this function.
+ *   This function is called by application-specific, setup logic to
+ *   configure the touchscreen device.  This function will register the driver
+ *   as /dev/inputN where N is the minor device number.
+ *
+ * Input Parameters:
+ *   minor   - The input device minor number
+ *
+ * Returned Value:
+ *   Zero is returned on success.  Otherwise, a negated errno value is
+ *   returned to indicate the nature of the failure.
+ *
+ ****************************************************************************/
+
+int arch_tcinitialize(int minor)
+{
+  FAR struct spi_dev_s *dev;
+  int ret;
+
+  idbg("minor %d\n", minor);
+  DEBUGASSERT(minor == 0);
+
+  /* Configure and enable the ADS7843E interrupt pin as an input */
+
+  (void)sam_configgpio(GPIO_TCS_BUSY);
+  (void)sam_configgpio(GPIO_TCS_IRQ);
+
+  /* Configure the PIO interrupt */
+
+  sam_gpioirq(GPIO_TCS_IRQ);
+
+  /* Get an instance of the SPI interface for the touchscreen chip select */
+
+  dev = up_spiinitialize(TSC_CSNUM);
+  if (!dev)
+    {
+      idbg("Failed to initialize SPI chip select %d\n", TSC_CSNUM);
+      return -ENODEV;
+    }
+
+  /* Initialize and register the SPI touschscreen device */
+
+  ret = ads7843e_register(dev, &g_tscinfo, CONFIG_ADS7843E_DEVMINOR);
+  if (ret < 0)
+    {
+      idbg("Failed to initialize SPI chip select %d\n", TSC_CSNUM);
+      /* up_spiuninitialize(dev); */
+      return -ENODEV;
+    }
+
+  return OK;
+}
+
+/****************************************************************************
+ * Name: arch_tcuninitialize
+ *
+ * Description:
+ *   Each board that supports a touchscreen device must provide this function.
+ *   This function is called by application-specific, setup logic to
+ *   uninitialize the touchscreen device.
+ *
+ * Input Parameters:
+ *   None
+ *
+ * Returned Value:
+ *   None.
+ *
+ ****************************************************************************/
+
+void arch_tcuninitialize(void)
+{
+  /* No support for un-initializing the touchscreen ADS7843E device yet */
+}
+
+#endif /* CONFIG_INPUT && CONFIG_INPUT_ADS7843E */