mirror of
https://github.com/apache/nuttx.git
synced 2026-05-24 07:46:16 +08:00
SAMV7 USB: Move clock initialization back to sam_clockconfig.c; add seperate UTMI register definition header file; fix a couple of typo bugs
This commit is contained in:
Gregory Nutt
@@ -1,7 +1,7 @@
|
||||
/************************************************************************************************************
|
||||
* arch/arm/src/samv7/chip/sam_usbhs.h
|
||||
*
|
||||
* Copyright (C) 2013 Gregory Nutt. All rights reserved.
|
||||
* Copyright (C) 2015 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* References:
|
||||
@@ -126,10 +126,6 @@
|
||||
#define SAM_USBHS_SCR_OFFSET 0x0808 /* General Status Clear Register */
|
||||
#define SAM_USBHS_SFR_OFFSET 0x080c /* General Status Set Register */
|
||||
/* 0x0810-0x082c: Reserved */
|
||||
/* UTMI Registers */
|
||||
|
||||
#define SAM_UTMI_OHCIICR_OFFSET 0x0010 /* OHCI Interrupt Configuration Register */
|
||||
#define SAM_UTMI_CKTRIM_OFFSET 0x0030 /* UTMI Clock Trimming Register */
|
||||
|
||||
/* Register addresses ***************************************************************************************/
|
||||
|
||||
@@ -195,11 +191,6 @@
|
||||
#define SAM_USBHS_SCR (SAM_USBHS_BASE+SAM_USBHS_SCR_OFFSET)
|
||||
#define SAM_USBHS_SFR (SAM_USBHS_BASE+SAM_USBHS_SFR_OFFSET)
|
||||
|
||||
/* UTMI Registers */
|
||||
|
||||
#define SAM_UTMI_OHCIICR (SAM_UTMI_BASE+SAM_UTMI_OHCIICR_OFFSET)
|
||||
#define SAM_UTMI_CKTRIM (SAM_UTMI_BASE+SAM_UTMI_CKTRIM_OFFSET)
|
||||
|
||||
/* Register bit-field definitions ***************************************************************************/
|
||||
|
||||
/* USBHS Device Controller Register Bit Field Definitions */
|
||||
@@ -304,7 +295,7 @@
|
||||
|
||||
/* Device Endpoint Configuration Register */
|
||||
|
||||
#define USBHS_DEVEPTCFG_ALLOC (1 << 0) /* Bit 0: Endpoint Memory Allocate */
|
||||
#define USBHS_DEVEPTCFG_ALLOC (1 << 1) /* Bit 1: Endpoint Memory Allocate */
|
||||
#define USBHS_DEVEPTCFG_EPBK_SHIFT (2) /* Bits 2-3: Endpoint Banks */
|
||||
#define USBHS_DEVEPTCFG_EPBK_MASK (3 << USBHS_DEVEPTCFG_EPBK_SHIFT)
|
||||
# define USBHS_DEVEPTCFG_EPBK(n) ((uint32_t)((n)-1) << USBHS_DEVEPTCFG_EPBK_SHIFT)
|
||||
@@ -779,22 +770,6 @@
|
||||
|
||||
#define USBHS_SFR_RDERRIS (1 << 4) /* Bit 4: Remote Device Connection Error Interrupt Set */
|
||||
|
||||
/* UTMI Registers */
|
||||
|
||||
/* OHCI Interrupt Configuration Register */
|
||||
|
||||
#define UTMI_OHCIICR_RES0 (1 << 0) /* Bit 0: USB PORT0 Reset */
|
||||
#define UTMI_OHCIICR_ARIE (1 << 4) /* Bit 4: OHCI Asynchronous Resume Interrupt Enable */
|
||||
#define UTMI_OHCIICR_APPSTART (0 << 5) /* Bit 5: Reserved, must be zero */
|
||||
#define UTMI_OHCIICR_UDPPUDIS (1 << 23) /* Bit 23: USB Device Pull-up Disable */
|
||||
|
||||
/* UTMI Clock Trimming Register */
|
||||
|
||||
#define UTMI_CKTRIM_FREQ_SHIFT (0) /* Bits 0-1: UTMI Reference Clock Frequency */
|
||||
#define UTMI_CKTRIM_FREQ_MASK (3 << UTMI_CKTRIM_FREQ_SHIFT)
|
||||
# define UTMI_CKTRIM_FREQ_XTAL12 (0 << UTMI_CKTRIM_FREQ_SHIFT) /* 12 MHz reference clock */
|
||||
# define UTMI_CKTRIM_FREQ_XTAL16 (1 << UTMI_CKTRIM_FREQ_SHIFT) /* 16 MHz reference clock */
|
||||
|
||||
/************************************************************************************************************
|
||||
* Public Types
|
||||
************************************************************************************************************/
|
||||
|
||||
@@ -0,0 +1,92 @@
|
||||
/************************************************************************************************************
|
||||
* arch/arm/src/samv7/chip/sam_utmi.h
|
||||
*
|
||||
* Copyright (C) 2015 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* References:
|
||||
* SAMV7D3 Series Data Sheet
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
************************************************************************************************************/
|
||||
|
||||
#ifndef __ARCH_ARM_SRC_SAMV7_CHIP_SAM_UTMI_H
|
||||
#define __ARCH_ARM_SRC_SAMV7_CHIP_SAM_UTMI_H
|
||||
|
||||
/************************************************************************************************************
|
||||
* Included Files
|
||||
************************************************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
#include <arch/samv7/chip.h>
|
||||
|
||||
#include "chip/sam_memorymap.h"
|
||||
|
||||
/************************************************************************************************************
|
||||
* Pre-processor Definitions
|
||||
************************************************************************************************************/
|
||||
/* Register offsets *****************************************************************************************/
|
||||
|
||||
#define SAM_UTMI_OHCIICR_OFFSET 0x0010 /* OHCI Interrupt Configuration Register */
|
||||
#define SAM_UTMI_CKTRIM_OFFSET 0x0030 /* UTMI Clock Trimming Register */
|
||||
|
||||
/* Register addresses ***************************************************************************************/
|
||||
|
||||
#define SAM_UTMI_OHCIICR (SAM_UTMI_BASE+SAM_UTMI_OHCIICR_OFFSET)
|
||||
#define SAM_UTMI_CKTRIM (SAM_UTMI_BASE+SAM_UTMI_CKTRIM_OFFSET)
|
||||
|
||||
/* Register bit-field definitions ***************************************************************************/
|
||||
|
||||
/* OHCI Interrupt Configuration Register */
|
||||
|
||||
#define UTMI_OHCIICR_RES0 (1 << 0) /* Bit 0: USB PORT0 Reset */
|
||||
#define UTMI_OHCIICR_ARIE (1 << 4) /* Bit 4: OHCI Asynchronous Resume Interrupt Enable */
|
||||
#define UTMI_OHCIICR_APPSTART (0 << 5) /* Bit 5: Reserved, must be zero */
|
||||
#define UTMI_OHCIICR_UDPPUDIS (1 << 23) /* Bit 23: USB Device Pull-up Disable */
|
||||
|
||||
/* UTMI Clock Trimming Register */
|
||||
|
||||
#define UTMI_CKTRIM_FREQ_SHIFT (0) /* Bits 0-1: UTMI Reference Clock Frequency */
|
||||
#define UTMI_CKTRIM_FREQ_MASK (3 << UTMI_CKTRIM_FREQ_SHIFT)
|
||||
# define UTMI_CKTRIM_FREQ_XTAL12 (0 << UTMI_CKTRIM_FREQ_SHIFT) /* 12 MHz reference clock */
|
||||
# define UTMI_CKTRIM_FREQ_XTAL16 (1 << UTMI_CKTRIM_FREQ_SHIFT) /* 16 MHz reference clock */
|
||||
|
||||
/************************************************************************************************************
|
||||
* Public Types
|
||||
************************************************************************************************************/
|
||||
|
||||
/************************************************************************************************************
|
||||
* Public Data
|
||||
************************************************************************************************************/
|
||||
|
||||
/************************************************************************************************************
|
||||
* Public Functions
|
||||
************************************************************************************************************/
|
||||
|
||||
#endif /* __ARCH_ARM_SRC_SAMV7_CHIP_SAM_UTMI_H */
|
||||
@@ -54,11 +54,17 @@
|
||||
#include "chip/sam_wdt.h"
|
||||
#include "chip/sam_supc.h"
|
||||
#include "chip/sam_matrix.h"
|
||||
#include "chip/sam_utmi.h"
|
||||
|
||||
/****************************************************************************
|
||||
* Pre-processor Definitions
|
||||
****************************************************************************/
|
||||
/* Configuration ***********************************************************/
|
||||
/* Not yet supported */
|
||||
|
||||
#undef CONFIG_SAMV7_USBDEVHS_LOWPOWER
|
||||
|
||||
/* Board Settings **********************************************************/
|
||||
/* PMC register settings based on the board configuration values defined
|
||||
* in board.h
|
||||
*/
|
||||
@@ -223,6 +229,80 @@ static inline void sam_pmcsetup(void)
|
||||
putreg32(BOARD_CKGR_PLLAR, SAM_PMC_CKGR_PLLAR);
|
||||
sam_pmcwait(PMC_INT_LOCKA);
|
||||
|
||||
#ifdef CONFIG_USBDEV
|
||||
/* UTMI configuration: Enable port0, select 12/16 MHz MAINOSC crystal source */
|
||||
|
||||
#if 0 /* REVISIT: Does this apply only to OHCI? */
|
||||
putreg32(UTMI_OHCIICR_RES0, SAM_UTMI_OHCIICR);
|
||||
#endif
|
||||
|
||||
#if BOARD_MAINOSC_FREQUENCY == 12000000
|
||||
putreg32(UTMI_CKTRIM_FREQ_XTAL12, SAM_UTMI_CKTRIM);
|
||||
#elif BOARD_MAINOSC_FREQUENCY == 12000000
|
||||
putreg32(UTMI_CKTRIM_FREQ_XTAL16, SAM_UTMI_CKTRIM);
|
||||
#else
|
||||
# error ERROR: Unrecognized MAINSOSC frequency
|
||||
#endif
|
||||
|
||||
/* Enable UTMI Clocking. The USBHS can work in two modes:
|
||||
*
|
||||
* - Normal mode where High speed, Full speed and Low speed are available.
|
||||
* - Low-power mode where only Full speed and Low speed are available.
|
||||
*
|
||||
* Only the normal mode is supported by this logic.
|
||||
*/
|
||||
|
||||
#ifdef CONFIG_SAMV7_USBDEVHS_LOWPOWER
|
||||
/* UTMI Low-power mode, Full/Low Speed mode
|
||||
*
|
||||
* Enable the 48MHz FS Clock.
|
||||
*/
|
||||
|
||||
putreg32(PMC_USBCLK, SAM_PMC_SCER);
|
||||
|
||||
#else
|
||||
/* UTMI normal mode, High/Full/Low Speed
|
||||
*
|
||||
* Disable the 48MHz USB FS Clock. It is not used in this configuration
|
||||
*/
|
||||
|
||||
putreg32(PMC_USBCLK, SAM_PMC_SCDR);
|
||||
#endif
|
||||
|
||||
/* Select the UTMI PLL as the USB PLL clock input (480MHz) with divider
|
||||
* to get to 48MHz. UPLL output frequency is determined only by the
|
||||
* 12/16MHz crystal selection above.
|
||||
*/
|
||||
|
||||
regval = PMC_USB_USBS_UPLL;
|
||||
|
||||
#ifdef CONFIG_SAMV7_USBDEVHS_LOWPOWER
|
||||
if ((getreg32(SAM_PMC_MCKR) & PMC_MCKR_PLLADIV2) != 0)
|
||||
{
|
||||
/* Divider = 480 Mhz / 2 / 48 Mhz = 5 */
|
||||
|
||||
regval |= PMC_USB_USBDIV(4);
|
||||
}
|
||||
else
|
||||
{
|
||||
/* Divider = 480 Mhz / 1 / 48 Mhz = 10 */
|
||||
|
||||
regval |= PMC_USB_USBDIV(9);
|
||||
}
|
||||
#endif
|
||||
|
||||
putreg32(regval, SAM_PMC_USB);
|
||||
|
||||
/* Enable the UTMI PLL with the maximum start-up time */
|
||||
|
||||
regval = PMC_CKGR_UCKR_UPLLEN | PMC_CKGR_UCKR_UPLLCOUNT_MAX;
|
||||
putreg32(regval, SAM_PMC_CKGR_UCKR);
|
||||
|
||||
/* Wait for LOCKU */
|
||||
|
||||
sam_pmcwait(PMC_INT_LOCKU);
|
||||
#endif
|
||||
|
||||
/* Switch to the fast clock and wait for MCKRDY */
|
||||
|
||||
putreg32(BOARD_PMC_MCKR_FAST, SAM_PMC_MCKR);
|
||||
|
||||
@@ -73,7 +73,6 @@
|
||||
#include "cache.h"
|
||||
|
||||
#include "sam_periphclks.h"
|
||||
#include "chip/sam_pmc.h"
|
||||
#include "chip/sam_usbhs.h"
|
||||
#include "sam_usbdev.h"
|
||||
|
||||
@@ -118,7 +117,7 @@
|
||||
#define EP0 (0)
|
||||
#define SAM_EPSET_ALL (0xffff) /* All endpoints */
|
||||
#define SAM_EPSET_NOTEP0 (0xfffe) /* All endpoints except EP0 */
|
||||
#define SAM_EPSET_DMA (0x00fe) /* All endpoints that support DMA transfers */
|
||||
#define SAM_EPSET_DMA (0x01fe) /* All endpoints that support DMA transfers */
|
||||
#define SAM_EP_BIT(ep) (1 << (ep))
|
||||
#define SAM_EP0_MAXPACKET (64) /* EP0 Max. packet size */
|
||||
|
||||
@@ -479,6 +478,8 @@ static inline bool
|
||||
sam_ep_reserved(struct sam_usbdev_s *priv, int epno);
|
||||
static int sam_ep_configure_internal(struct sam_ep_s *privep,
|
||||
const struct usb_epdesc_s *desc);
|
||||
static inline int
|
||||
sam_ep0_configure(struct sam_usbdev_s *priv);
|
||||
|
||||
/* Endpoint operations ******************************************************/
|
||||
|
||||
@@ -815,26 +816,26 @@ static void sam_dumpep(struct sam_usbdev_s *priv, int epno)
|
||||
/* Global Registers */
|
||||
|
||||
lldbg("Global Register:\n");
|
||||
lldbg(" CTRL: %04x\n", sam_getreg(SAM_USBHS_DEVCTRL));
|
||||
lldbg(" IISR: %04x\n", sam_getreg(SAM_USBHS_DEVISR));
|
||||
lldbg(" IMR: %04x\n", sam_getreg(SAM_USBHS_DEVIMR));
|
||||
lldbg(" EPT: %04x\n", sam_getreg(SAM_USBHS_DEVEPT));
|
||||
lldbg(" FNUM: %04x\n", sam_getreg(SAM_USBHS_DEVFNUM));
|
||||
lldbg(" CTRL: %08x\n", sam_getreg(SAM_USBHS_DEVCTRL));
|
||||
lldbg(" IISR: %08x\n", sam_getreg(SAM_USBHS_DEVISR));
|
||||
lldbg(" IMR: %08x\n", sam_getreg(SAM_USBHS_DEVIMR));
|
||||
lldbg(" EPT: %08x\n", sam_getreg(SAM_USBHS_DEVEPT));
|
||||
lldbg(" FNUM: %08x\n", sam_getreg(SAM_USBHS_DEVFNUM));
|
||||
|
||||
/* Endpoint registers */
|
||||
|
||||
lldbg("Endpoint %d Register:\n", epno);
|
||||
lldbg(" CFG: %04x\n", sam_getreg(SAM_USBHS_DEVEPTCFG(epno)));
|
||||
lldbg(" ISR: %04x\n", sam_getreg(SAM_USBHS_DEVEPTISR(epno)));
|
||||
lldbg(" IMR: %04x\n", sam_getreg(SAM_USBHS_DEVEPTIMR(epno)));
|
||||
lldbg(" CFG: %08x\n", sam_getreg(SAM_USBHS_DEVEPTCFG(epno)));
|
||||
lldbg(" ISR: %08x\n", sam_getreg(SAM_USBHS_DEVEPTISR(epno)));
|
||||
lldbg(" IMR: %08x\n", sam_getreg(SAM_USBHS_DEVEPTIMR(epno)));
|
||||
|
||||
lldbg("DMA %d Register:\n", epno);
|
||||
if ((SAM_EPSET_DMA & SAM_EP_BIT(epno)) != 0)
|
||||
{
|
||||
lldbg(" NXTDSC: %04x\n", sam_getreg(SAM_USBHS_DEVDMANXTDSC(epno)));
|
||||
lldbg(" ADDRESS: %04x\n", sam_getreg(SAM_USBHS_DEVDMAADDR(epno)));
|
||||
lldbg(" CONTROL: %04x\n", sam_getreg(SAM_USBHS_DEVDMACTRL(epno)));
|
||||
lldbg(" STATUS: %04x\n", sam_getreg(SAM_USBHS_DEVDMASTA(epno)));
|
||||
lldbg(" NXTDSC: %08x\n", sam_getreg(SAM_USBHS_DEVDMANXTDSC(epno)));
|
||||
lldbg(" ADDRESS: %08x\n", sam_getreg(SAM_USBHS_DEVDMAADDR(epno)));
|
||||
lldbg(" CONTROL: %08x\n", sam_getreg(SAM_USBHS_DEVDMACTRL(epno)));
|
||||
lldbg(" STATUS: %08x\n", sam_getreg(SAM_USBHS_DEVDMASTA(epno)));
|
||||
}
|
||||
else
|
||||
{
|
||||
@@ -3306,7 +3307,7 @@ static int sam_ep_configure_internal(struct sam_ep_s *privep,
|
||||
|
||||
sam_putreg(USBHS_DEVEPTIDR_ALLINTS, SAM_USBHS_DEVEPTIDR(epno));
|
||||
|
||||
/* Reset Endpoint FIFOs */
|
||||
/* Clear toggle and stall indications */
|
||||
|
||||
sam_putreg(USBHS_DEVEPTISR_DTSEQ_MASK | USBHS_DEVEPTINT_STALLEDI,
|
||||
SAM_USBHS_DEVEPTICR(epno));
|
||||
@@ -3382,6 +3383,7 @@ static int sam_ep_configure_internal(struct sam_ep_s *privep,
|
||||
* the FIFO maximum capacity and the maximum number of allowed banks.
|
||||
*/
|
||||
|
||||
regaddr = SAM_USBHS_DEVEPTISR(epno);
|
||||
if ((sam_getreg(regaddr) & USBHS_DEVEPTISR_CFGOK) == 0)
|
||||
{
|
||||
usbtrace(TRACE_DEVERROR(SAM_TRACEERR_NCFGOK), epno);
|
||||
@@ -3444,6 +3446,19 @@ static int sam_ep_configure_internal(struct sam_ep_s *privep,
|
||||
return OK;
|
||||
}
|
||||
|
||||
/****************************************************************************
|
||||
* Name: sam_ep0_configure
|
||||
*
|
||||
* Description:
|
||||
* Configure EP0 for normal operation.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
static inline int sam_ep0_configure(struct sam_usbdev_s *priv)
|
||||
{
|
||||
return sam_ep_configure_internal(&priv->eplist[EP0], &g_ep0desc);
|
||||
}
|
||||
|
||||
/****************************************************************************
|
||||
* Endpoint operations
|
||||
****************************************************************************/
|
||||
@@ -4232,7 +4247,7 @@ static void sam_reset(struct sam_usbdev_s *priv)
|
||||
/* Reset and disable all endpoints other. Then re-configure EP0 */
|
||||
|
||||
sam_epset_reset(priv, SAM_EPSET_ALL);
|
||||
sam_ep_configure_internal(&priv->eplist[EP0], &g_ep0desc);
|
||||
sam_ep0_configure(priv);
|
||||
|
||||
/* Reset endpoint data structures */
|
||||
|
||||
@@ -4306,6 +4321,8 @@ static void sam_hw_setup(struct sam_usbdev_s *priv)
|
||||
* 2. Enable the USBHS (UIMOD = 1, USBE = 1, FRZCLK = 0).
|
||||
* 3. Enable the UPLL 480 MHz.
|
||||
* 4. Wait for the UPLL 480 MHz to be considered as locked by the PMC.
|
||||
*
|
||||
* Steps 1,3, and 4 were performed in sam_clockconfig.c.
|
||||
*/
|
||||
|
||||
/* Enable the USBHS peripheral clock (PMC_PCER) */
|
||||
@@ -4325,65 +4342,6 @@ static void sam_hw_setup(struct sam_usbdev_s *priv)
|
||||
regval |= USBHS_CTRL_UIMOD_DEVICE;
|
||||
sam_putreg(regval, SAM_USBHS_CTRL);
|
||||
|
||||
/* UTMI configuration: Enable port0, select 12/16 MHz MAINOSC crystal source */
|
||||
|
||||
#if 0 /* REVISIT: Does this apply only to OHCI? */
|
||||
sam_putreg(UTMI_OHCIICR_RES0, SAM_UTMI_OHCIICR);
|
||||
#endif
|
||||
|
||||
#if BOARD_MAINOSC_FREQUENCY == 12000000
|
||||
sam_putreg(UTMI_CKTRIM_FREQ_XTAL12, SAM_UTMI_CKTRIM);
|
||||
#elif BOARD_MAINOSC_FREQUENCY == 12000000
|
||||
sam_putreg(UTMI_CKTRIM_FREQ_XTAL16, SAM_UTMI_CKTRIM);
|
||||
#else
|
||||
# error ERROR: Unrecognized MAINSOSC frequency
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_SAMV7_USBDEVHS_LOWPOWER
|
||||
/* UTMI Full/Low Speed mode */
|
||||
|
||||
sam_putreg(PMC_USBCLK, SAM_PMC_SCER);
|
||||
#else
|
||||
/* UTMI parallel mode, High/Full/Low Speed
|
||||
*
|
||||
* Disable 48MHz USB FS Clock. It is not used in this configuration
|
||||
*/
|
||||
|
||||
sam_putreg(PMC_USBCLK, SAM_PMC_SCDR);
|
||||
#endif
|
||||
|
||||
/* Select the UTMI PLL as the USB PLL clock input (480MHz) with divider
|
||||
* to get to 48MHz.
|
||||
*/
|
||||
|
||||
regval = PMC_USB_USBS_UPLL;
|
||||
|
||||
#ifdef CONFIG_SAMV7_USBDEVHS_LOWPOWER
|
||||
if ((sam_getreg(SAM_PMC_MCKR) & PMC_MCKR_PLLADIV2) != 0)
|
||||
{
|
||||
/* Divider = 480 Mhz / 2 / 48 Mhz = 5 */
|
||||
|
||||
regval |= PMC_USB_USBDIV(4);
|
||||
}
|
||||
else
|
||||
{
|
||||
/* Divider = 480 Mhz / 1 / 48 Mhz = 10 */
|
||||
|
||||
regval |= PMC_USB_USBDIV(9);
|
||||
}
|
||||
#endif
|
||||
|
||||
sam_putreg(regval, SAM_PMC_USB);
|
||||
|
||||
/* Enable the UTMI PLL with the maximum start-up time */
|
||||
|
||||
regval = PMC_CKGR_UCKR_UPLLEN | PMC_CKGR_UCKR_UPLLCOUNT_MAX;
|
||||
sam_putreg(regval, SAM_PMC_CKGR_UCKR);
|
||||
|
||||
/* Wait for LOCKU */
|
||||
|
||||
while ((sam_getreg(SAM_PMC_SR) & PMC_INT_LOCKU) == 0);
|
||||
|
||||
/* Select High Speed */
|
||||
|
||||
regval = sam_getreg(SAM_USBHS_DEVCTRL);
|
||||
|
||||
Reference in New Issue
Block a user