mirror of
https://github.com/grblHAL/core.git
synced 2026-08-17 16:41:45 +08:00
Fixed silly typedef mistake in setting struct, added settings $392 and $393 for spindle and coolant startup delays on safety door open.
This commit is contained in:
Terje Io
@@ -27,68 +27,68 @@
|
||||
#include "core_handlers.h"
|
||||
|
||||
PROGMEM static const status_detail_t status_detail[] = {
|
||||
{ Status_OK, "ok", NULL },
|
||||
{ Status_ExpectedCommandLetter, "Expected command letter", "G-code words consist of a letter and a value. Letter was not found." },
|
||||
{ Status_BadNumberFormat, "Bad number format", "Missing the expected G-code word value or numeric value format is not valid." },
|
||||
{ Status_InvalidStatement, "Invalid statement", "'$' system command was not recognized or supported." },
|
||||
{ Status_NegativeValue, "Value < 0", "Negative value received for an expected positive value." },
|
||||
{ Status_HomingDisabled, "Homing disabled", "Homing cycle failure. Homing is not configured via settings." },
|
||||
{ Status_SettingStepPulseMin, "Value < 2 microseconds", "Step pulse time must be greater or equal to 2 microseconds." },
|
||||
{ Status_SettingReadFail, "Settings read failed. Using defaults", "A settings read failed. Auto-restoring affected settings to default values." },
|
||||
{ Status_IdleError, "Not idle", "'$' command cannot be used unless controller state is IDLE. Ensures smooth operation during a job." },
|
||||
{ Status_SystemGClock, "G-code lock", "G-code commands are locked out during alarm or jog state." },
|
||||
{ Status_SoftLimitError, "Homing not enabled", "Soft limits cannot be enabled without homing also enabled." },
|
||||
{ Status_Overflow, "Line overflow", "Max characters per line exceeded. Received command line was not executed." },
|
||||
{ Status_MaxStepRateExceeded, "Max step rate too high", "'$' setting value cause the step rate to exceed the maximum supported." },
|
||||
{ Status_CheckDoor, "Check Door", "Safety door detected as opened and door state initiated." },
|
||||
{ Status_LineLengthExceeded, "Line length exceeded", "Build info or startup line exceeded line length limit. Line not stored." },
|
||||
{ Status_TravelExceeded, "Travel exceeded", "Jog target exceeds machine travel. Jog command has been ignored." },
|
||||
{ Status_InvalidJogCommand, "Invalid jog command", "Jog command has no '=' or contains prohibited g-code." },
|
||||
{ Status_SettingDisabledLaser, "Setting disabled", "Laser mode requires PWM output." },
|
||||
{ Status_Reset, "Reset asserted", "" },
|
||||
{ Status_NonPositiveValue, "Non positive value", "" },
|
||||
{ Status_GcodeUnsupportedCommand, "Unsupported command", "Unsupported or invalid g-code command found in block." },
|
||||
{ Status_GcodeModalGroupViolation, "Modal group violation", "More than one g-code command from same modal group found in block." },
|
||||
{ Status_GcodeUndefinedFeedRate, "Undefined feed rate", "Feed rate has not yet been set or is undefined." },
|
||||
{ Status_GcodeCommandValueNotInteger, "Invalid gcode ID:23", "G-code command in block requires an integer value." },
|
||||
{ Status_GcodeAxisCommandConflict, "Invalid gcode ID:24", "More than one g-code command that requires axis words found in block." },
|
||||
{ Status_GcodeWordRepeated, "Invalid gcode ID:25", "Repeated g-code word found in block." },
|
||||
{ Status_GcodeNoAxisWords, "Invalid gcode ID:26", "No axis words found in block for g-code command or current modal state which requires them." },
|
||||
{ Status_GcodeInvalidLineNumber, "Invalid gcode ID:27", "Line number value is invalid." },
|
||||
{ Status_GcodeValueWordMissing, "Invalid gcode ID:28", "G-code command is missing a required value word." },
|
||||
{ Status_GcodeUnsupportedCoordSys, "Invalid gcode ID:29", "G59.x work coordinate systems are not supported." },
|
||||
{ Status_GcodeG53InvalidMotionMode, "Invalid gcode ID:30", "G53 only allowed with G0 and G1 motion modes." },
|
||||
{ Status_GcodeAxisWordsExist, "Invalid gcode ID:31", "Axis words found in block when no command or current modal state uses them." },
|
||||
{ Status_GcodeNoAxisWordsInPlane, "Invalid gcode ID:32", "G2 and G3 arcs require at least one in-plane axis word." },
|
||||
{ Status_GcodeInvalidTarget, "Invalid gcode ID:33", "Motion command target is invalid." },
|
||||
{ Status_GcodeArcRadiusError, "Invalid gcode ID:34", "Arc radius value is invalid." },
|
||||
{ Status_GcodeNoOffsetsInPlane, "Invalid gcode ID:35", "G2 and G3 arcs require at least one in-plane offset word." },
|
||||
{ Status_GcodeUnusedWords, "Invalid gcode ID:36", "Unused value words found in block." },
|
||||
{ Status_GcodeG43DynamicAxisError, "Invalid gcode ID:37", "G43.1 dynamic tool length offset is not assigned to configured tool length axis." },
|
||||
{ Status_GcodeIllegalToolTableEntry, "Invalid gcode ID:38", "Tool number greater than max supported value or undefined tool selected." },
|
||||
{ Status_GcodeValueOutOfRange, "Invalid gcode ID:39", "Value out of range." },
|
||||
{ Status_GcodeToolChangePending, "Invalid gcode ID:40", "G-code command not allowed when tool change is pending." },
|
||||
{ Status_GcodeSpindleNotRunning, "Invalid gcode ID:41", "Spindle not running when motion commanded in CSS or spindle sync mode." },
|
||||
{ Status_GcodeIllegalPlane, "Invalid gcode ID:42", "Plane must be ZX for threading." },
|
||||
{ Status_GcodeMaxFeedRateExceeded, "Invalid gcode ID:43", "Max. feed rate exceeded." },
|
||||
{ Status_GcodeRPMOutOfRange, "Invalid gcode ID:44", "RPM out of range." },
|
||||
{ Status_LimitsEngaged, "Limit switch engaged", "Only homing is allowed when a limit switch is engaged." },
|
||||
{ Status_HomingRequired, "Homing required", "Home machine to continue." },
|
||||
{ Status_GCodeToolError, "Invalid gcode ID:47", "ATC: current tool is not set. Set current tool with M61." },
|
||||
{ Status_ValueWordConflict, "Invalid gcode ID:48", "Value word conflict." },
|
||||
{ Status_SelfTestFailed, "Self test failed", "Power on self test failed. A hard reset is required." },
|
||||
{ Status_EStop, "E-stop", "Emergency stop active." },
|
||||
{ Status_MotorFault, "Motor fault", "Motor fault." },
|
||||
{ Status_SettingValueOutOfRange, "Value out of range.", "Setting value is out of range." },
|
||||
{ Status_SettingDisabled, "Setting disabled", "Setting is not available, possibly due to limited driver support." },
|
||||
{ Status_GcodeInvalidRetractPosition, "Invalid gcode ID:54", "Retract position is less than drill depth." },
|
||||
{ Status_OK, NULL },
|
||||
{ Status_ExpectedCommandLetter, "G-code words consist of a letter and a value. Letter was not found." },
|
||||
{ Status_BadNumberFormat, "Missing the expected G-code word value or numeric value format is not valid." },
|
||||
{ Status_InvalidStatement, "'$' system command was not recognized or supported." },
|
||||
{ Status_NegativeValue, "Negative value received for an expected positive value." },
|
||||
{ Status_HomingDisabled, "Homing cycle failure. Homing is not configured via settings." },
|
||||
{ Status_SettingStepPulseMin, "Step pulse time must be greater or equal to 2 microseconds." },
|
||||
{ Status_SettingReadFail, "A settings read failed. Auto-restoring affected settings to default values." },
|
||||
{ Status_IdleError, "'$' command cannot be used unless controller state is IDLE. Ensures smooth operation during a job." },
|
||||
{ Status_SystemGClock, "G-code commands are locked out during alarm or jog state." },
|
||||
{ Status_SoftLimitError, "Soft limits cannot be enabled without homing also enabled." },
|
||||
{ Status_Overflow, "Max characters per line exceeded. Received command line was not executed." },
|
||||
{ Status_MaxStepRateExceeded, "'$' setting value cause the step rate to exceed the maximum supported." },
|
||||
{ Status_CheckDoor, "Safety door detected as opened and door state initiated." },
|
||||
{ Status_LineLengthExceeded, "Build info or startup line exceeded line length limit. Line not stored." },
|
||||
{ Status_TravelExceeded, "Jog target exceeds machine travel. Jog command has been ignored." },
|
||||
{ Status_InvalidJogCommand, "Jog command has no '=' or contains prohibited g-code." },
|
||||
{ Status_SettingDisabledLaser, "Laser mode requires PWM output." },
|
||||
{ Status_Reset, "Reset asserted" },
|
||||
{ Status_NonPositiveValue, "Non positive value" },
|
||||
{ Status_GcodeUnsupportedCommand, "Unsupported or invalid g-code command found in block." },
|
||||
{ Status_GcodeModalGroupViolation, "More than one g-code command from same modal group found in block." },
|
||||
{ Status_GcodeUndefinedFeedRate, "Feed rate has not yet been set or is undefined." },
|
||||
{ Status_GcodeCommandValueNotInteger, "G-code command in block requires an integer value." },
|
||||
{ Status_GcodeAxisCommandConflict, "More than one g-code command that requires axis words found in block." },
|
||||
{ Status_GcodeWordRepeated, "Repeated g-code word found in block." },
|
||||
{ Status_GcodeNoAxisWords, "No axis words found in block for g-code command or current modal state which requires them." },
|
||||
{ Status_GcodeInvalidLineNumber, "Line number value is invalid." },
|
||||
{ Status_GcodeValueWordMissing, "G-code command is missing a required value word." },
|
||||
{ Status_GcodeUnsupportedCoordSys, "G59.x work coordinate systems are not supported." },
|
||||
{ Status_GcodeG53InvalidMotionMode, "G53 only allowed with G0 and G1 motion modes." },
|
||||
{ Status_GcodeAxisWordsExist, "Axis words found in block when no command or current modal state uses them." },
|
||||
{ Status_GcodeNoAxisWordsInPlane, "G2 and G3 arcs require at least one in-plane axis word." },
|
||||
{ Status_GcodeInvalidTarget, "Motion command target is invalid." },
|
||||
{ Status_GcodeArcRadiusError, "Arc radius value is invalid." },
|
||||
{ Status_GcodeNoOffsetsInPlane, "G2 and G3 arcs require at least one in-plane offset word." },
|
||||
{ Status_GcodeUnusedWords, "Unused value words found in block." },
|
||||
{ Status_GcodeG43DynamicAxisError, "G43.1 dynamic tool length offset is not assigned to configured tool length axis." },
|
||||
{ Status_GcodeIllegalToolTableEntry, "Tool number greater than max supported value or undefined tool selected." },
|
||||
{ Status_GcodeValueOutOfRange, "Value out of range." },
|
||||
{ Status_GcodeToolChangePending, "G-code command not allowed when tool change is pending." },
|
||||
{ Status_GcodeSpindleNotRunning, "Spindle not running when motion commanded in CSS or spindle sync mode." },
|
||||
{ Status_GcodeIllegalPlane, "Plane must be ZX for threading." },
|
||||
{ Status_GcodeMaxFeedRateExceeded, "Max. feed rate exceeded." },
|
||||
{ Status_GcodeRPMOutOfRange, "RPM out of range." },
|
||||
{ Status_LimitsEngaged, "Only homing is allowed when a limit switch is engaged." },
|
||||
{ Status_HomingRequired, "Home machine to continue." },
|
||||
{ Status_GCodeToolError, "ATC: current tool is not set. Set current tool with M61." },
|
||||
{ Status_ValueWordConflict, "Value word conflict." },
|
||||
{ Status_SelfTestFailed, "Power on self test failed. A hard reset is required." },
|
||||
{ Status_EStop, "Emergency stop active." },
|
||||
{ Status_MotorFault, "Motor fault." },
|
||||
{ Status_SettingValueOutOfRange, "Setting value is out of range." },
|
||||
{ Status_SettingDisabled, "Setting is not available, possibly due to limited driver support." },
|
||||
{ Status_GcodeInvalidRetractPosition, "Retract position is less than drill depth." },
|
||||
#if NGC_EXPRESSIONS_ENABLE
|
||||
{ Status_ExpressionUknownOp, "Unknown operation found in expression", "Unknown operation found in expression." },
|
||||
{ Status_ExpressionDivideByZero, "Divide by zero in expression", "Divide by zero in expression attempted." },
|
||||
{ Status_ExpressionArgumentOutOfRange, "Expression argument out of range", "Too large or too small argrument provided." },
|
||||
{ Status_ExpressionInvalidArgument, "Invalid expression argument", "Argument is not valid for the operation" },
|
||||
{ Status_ExpressionSyntaxError, "Syntax error in expression", "Expression is not valid." },
|
||||
{ Status_ExpressionInvalidResult, "Invalid result returned from expression", "Either NAN (not a number) or infinity was returned from expression." }
|
||||
{ Status_ExpressionUknownOp, "Unknown operation found in expression." },
|
||||
{ Status_ExpressionDivideByZero, "Divide by zero in expression attempted." },
|
||||
{ Status_ExpressionArgumentOutOfRange, "Too large or too small argrument provided." },
|
||||
{ Status_ExpressionInvalidArgument, "Argument is not valid for the operation" },
|
||||
{ Status_ExpressionSyntaxError, "Expression is not valid." },
|
||||
{ Status_ExpressionInvalidResult, "Either NAN (not a number) or infinity was returned from expression." }
|
||||
#endif
|
||||
};
|
||||
|
||||
|
||||
Reference in New Issue
Block a user