# AP-H743-R1 Flight Controller

<Badge type="tip" text="PX4 v1.17" />

:::warning
PX4 не розробляє цей (або будь-який інший) автопілот.
:::

The AP-H743-R1 is an advanced autopilot manufactured by X-MAV<sup>&reg;</sup>.

The autopilot is recommended for commercial system integration, but is also suitable for academic research and any other applications.
It brings you ultimate performance, stability, and reliability in every aspect.

![AP-H743-R1](../../assets/flight_controller/x-mav_ap-h743r1/ap-h743r1-main.png)

:::info
These flight controllers are [manufacturer supported](../flight_controller/autopilot_manufacturer_supported.md).
:::

### Processors & Sensors

- FMU Processor: STM32H743VIT6
  - 32 Bit Arm® Cortex®-M7, 480MHz, 2MB flash memory, 1MB RAM
- IO Processor: STM32F103
  - 32 Bit Arm® Cortex®-M3, 72MHz, 20KB SRAM
- Сенсори на платі
  - Accel/Gyro: ICM-42688-P\*2(Version1), BMI270\*2(Version2)
  - Mag: QMC5883P
  - Barometer: SPL06

### Інтерфейси

- 15x PWM Servo Outputs
- 1x Dedicated S.Bus Input
- 3x TELEM Ports
- 1x SERIAL4 Port
- 2x GPS Ports
- 1x USB Port (TYPE-C)
- 3x I2C Bus Ports
- 2x CAN Ports
- 2x Power Input Ports
  - ADC Power Input
  - DroneCAN/UAVCAN Power Input
- 2x Dedicated Debug Port
  - FMU Debug
  - IO Debug

## Purchase Channels {#store}

Order from [X-MAV](https://www.x-mav.cn/).

## Радіоуправління

A Radio Control (RC) system is required if you want to manually control your vehicle (PX4 does not require a radio system for autonomous flight modes).

Вам буде потрібно вибрати сумісний передавач/приймач та потім зв'язати їх, щоб вони взаємодіяли (прочитайте інструкції, що додаються до вашого конкретного передавача/приймача).

SBUS receivers connect to the SBUS-IN input port.
CRSF receiver must be wired to a spare port (UART) on the Flight Controller. Then you can bind the transmitter and receiver together.

## Налаштування послідовного порту

| UART   | Пристрій   | Порт    |
| ------ | ---------- | ------- |
| USART1 | /dev/ttyS0 | GPS     |
| USART2 | /dev/ttyS1 | GPS2    |
| USART3 | /dev/ttyS2 | TELEM1  |
| UART4  | /dev/ttyS3 | TELEM2  |
| UART7  | /dev/ttyS4 | TELEM3  |
| UART8  | /dev/ttyS5 | SERIAL4 |

## PWM Output

The AP-H743-R1 flight controller supports up to 15 PWM outputs.
The first 8 outputs (labelled M1 to M8) are controlled by a dedicated STM32F103 IOMCU controller.
The remaining 7 outputs (labelled A1 to A7) are the "auxiliary" outputs.
These are directly attached to the STM32H743 FMU controller .

The 15 PWM outputs are:

M1 - M8 are connected to the IOMCU.
A1 - A7 are connected to the FMU.

M1 - M8 support DShot and are in 3 groups:

- M1, M2 in group 1
- M3, M4 in group 2
- M5, M6, M7, M8 in group 3

The 7 FMU PWM outputs are in 3 groups:

- A1 - A4 are in one group.
- A5, A6 are in a 2nd group.
- A7 is in a 3rd group.

Channels within the same group need to use the same output rate.
If any channel in a group uses DShot then all channels in the group need to use DShot.

### Електричні дані

- Номінальна напруга:
  - Max input voltage: 5.4V
  - Вхід USB Power: 4.75~5.25V
  - Вхід на серворейку: 0\~9.9В

## Battery Monitoring

The board has connectors for 2 power monitors.

- POWER1 -- ADC
- POWER2 -- DroneCAN

The board is configure by default for a analog power monitor, and also has DroneCAN power monitor configured which is enabled.

## Збірка прошивки

To [build PX4](../dev_setup/building_px4.md) for this target, execute:

```sh
make x-mav_ap-h743r1_default
```

## Pinouts and Size

![AP-H743-R1 pinouts](../../assets/flight_controller/x-mav_ap-h743r1/ap-h743r1-pinouts.png)

![AP-H743-R1](../../assets/flight_controller/x-mav_ap-h743r1/ap-h743r1-size.png)

## Підтримувані платформи / Конструкції

Any multirotor/airplane/rover or boat that can be controlled using normal RC servos or Futaba S-Bus servos.
The complete set of supported configurations can be found in the [Airframe Reference](../airframes/airframe_reference.md).

## Debug Port {#debug_port}

### SWD

The [SWD interface](../debug/swd_debug.md) operate on the **FMU-DEBUG** port (`FMU-DEBUG`).

The debug port (`FMU-DEBUG`) uses a [JST SM04B-GHS-TB](https://www.digikey.com/en/products/detail/jst-sales-america-inc/SM04B-GHS-TB/807788) connector and has the following pinout:

| Pin                        | Сигнал                         | Вольтаж               |
| -------------------------- | ------------------------------ | --------------------- |
| 1 (red) | 5V+                            | +5V                   |
| 2 (blk) | FMU_SWDIO | +3.3V |
| 3 (blk) | FMU_SWCLK | +3.3V |
| 4 (blk) | GND                            | GND                   |