Mirrors_Framework/PX4-Autopilot
1
0
Fork 0
mirror of https://github.com/PX4/PX4-Autopilot.git synced 2026-05-24 15:40:31 +08:00
Code Issues Actions 8 Packages Projects Releases Wiki Activity

docs(i18n): PX4 guide translations (Crowdin) - ko (#27267)

Browse Source 
Co-authored-by: Crowdin Bot <support+bot@crowdin.com>
This commit is contained in:
PX4 Build Bot
2026-05-06 11:15:31 +10:00
committed by GitHub
parent 220a143a23
commit 929be2bef4
33 changed files with 524 additions and 298 deletions
Download Patch File Download Diff File Expand all files Collapse all files
docs/ko/peripherals/adsb_flarm.md
+18 -10
View File
@@ -18,7 +18,7 @@ It has been tested with the following devices:
Any of the devices can be connected to any free/unused serial port on the flight controller.
Most commonly they are connected to `TELEM2` (if this is not being use for some other purpose).
### PingRX
### PingRX Pro
The PingRX MAVLink port uses a JST ZHR-4 mating connector with pinout as shown below.
@@ -29,9 +29,17 @@ The PingRX MAVLink port uses a JST ZHR-4 mating connector with pinout as shown b
| 3 (흑) | 전원 | +4 to 6V |
| 4 (흑) | GND | GND |
The PingRX comes with connector cable that can be attached directly to the TELEM2 port (DF13-6P) on an [mRo Pixhawk](../flight_controller/mro_pixhawk.md).
The PingRX comes with connector cable that can be attached directly to the `TELEM2` port (DF13-6P) on an [mRo Pixhawk](../flight_controller/mro_pixhawk.md).
For other ports or boards, you will need to obtain your own cable.
The recommended port configuration for this receiver is:
| 매개변수 | Recommended Value |
| ------------------------------------------------------------------------------------------------------------------------------------------- | ----------------- |
| [MAV_X_CONFIG](../advanced_config/parameter_reference.md#MAV_1_CONFIG) | `TELEM 2` |
| [MAV_X_MODE](../advanced_config/parameter_reference.md#MAV_1_MODE) | uAvionix |
| [MAV_X_RADIO_CTL](../advanced_config/parameter_reference.md#MAV_1_RADIO_CTL) | Disabled |
## FLARM
FLARM has an on-board DF-13 6 Pin connector that has an identical pinout to the [mRo Pixhawk](../flight_controller/mro_pixhawk.md).
@@ -49,19 +57,19 @@ FLARM has an on-board DF-13 6 Pin connector that has an identical pinout to the
The TX and RX on the flight controller must be connected to the RX and TX on the FLARM, respectively.
:::
## 소프트웨어 설정
## PX4 설정
### Port Configuration
The receivers are configured in the same way as any other [MAVLink Peripheral](../peripherals/mavlink_peripherals.md).
The only _specific_ setup is that the port baud rate must be set to 57600 and the a low-bandwidth profile (`MAV_X_MODE`).
The recommended configuration for most devices (unless they have device-specific configuration like PingRX) is to connect to `TELEM 2` and [set the parameters](../advanced_config/parameters.md) as shown:
Assuming you have connected the device to the TELEM2 port, [set the parameters](../advanced_config/parameters.md) as shown:
- [MAV_1_CONFIG](../advanced_config/parameter_reference.md#MAV_1_CONFIG) = TELEM 2
- [MAV_1_MODE](../advanced_config/parameter_reference.md#MAV_1_MODE) = Normal
- [MAV_1_RATE](../advanced_config/parameter_reference.md#MAV_1_RATE) = 0 (default sending rate for port).
- [MAV_1_FORWARD](../advanced_config/parameter_reference.md#MAV_1_FORWARD) = Enabled
| 매개변수 | Recommended Value |
| ------------------------------------------------------------------------------------------------------------------ | ---------------------------------------------------- |
| [MAV_X_CONFIG](../advanced_config/parameter_reference.md#MAV_1_CONFIG) | `TELEM 2` |
| [MAV_X_MODE](../advanced_config/parameter_reference.md#MAV_1_MODE) | Normal |
| [MAV_X_RATE](../advanced_config/parameter_reference.md#MAV_1_RATE) | 0 (default sending rate for port) |
| [MAV_X_FORWARD](../advanced_config/parameter_reference.md#MAV_1_FORWARD) | Enabled |
Then reboot the vehicle.