diff --git a/docs/en/dronecan/ark_rtk_gps.md b/docs/en/dronecan/ark_rtk_gps.md
index e3114685fa8..76aeded7276 100644
--- a/docs/en/dronecan/ark_rtk_gps.md
+++ b/docs/en/dronecan/ark_rtk_gps.md
@@ -84,6 +84,7 @@ You need to set necessary [DroneCAN](index.md) parameters and define offsets if
 
 - Enable GPS yaw fusion by setting bit 3 of [EKF2_GPS_CTRL](../advanced_config/parameter_reference.md#EKF2_GPS_CTRL) to true.
 - Enable GPS blending to ensure the heading is always published by setting [SENS_GPS_MASK](../advanced_config/parameter_reference.md#SENS_GPS_MASK) to 7 (all three bits checked).
+- If using [Moving Baseline & GPS Heading](#setting-up-moving-baseline--gps-heading), set [SENS_GPS_PRIME](../advanced_config/parameter_reference.md#SENS_GPS_PRIME) to the CAN node ID of the _Moving Base_ module. The moving base is preferred because the rover receiver in a moving baseline configuration can experience degraded navigation rate and increased data latency when corrections are intermittent.
 - Enable [UAVCAN_SUB_GPS](../advanced_config/parameter_reference.md#UAVCAN_SUB_GPS), [UAVCAN_SUB_MAG](../advanced_config/parameter_reference.md#UAVCAN_SUB_MAG), and [UAVCAN_SUB_BARO](../advanced_config/parameter_reference.md#UAVCAN_SUB_BARO).
 - The parameters [EKF2_GPS_POS_X](../advanced_config/parameter_reference.md#EKF2_GPS_POS_X), [EKF2_GPS_POS_Y](../advanced_config/parameter_reference.md#EKF2_GPS_POS_Y) and [EKF2_GPS_POS_Z](../advanced_config/parameter_reference.md#EKF2_GPS_POS_Z) can be set to account for the offset of the ARK RTK GPS from the vehicles centre of gravity.
 
@@ -136,6 +137,7 @@ Setup via CAN:
 - On the _Moving Base_, set the following:
   - [GPS_UBX_MODE](../advanced_config/parameter_reference.md#GPS_UBX_MODE) to `4`.
   - [CANNODE_PUB_MBD](../advanced_config/parameter_reference.md#CANNODE_PUB_MBD) to `1`.
+- On the _Flight Controller_, set [SENS_GPS_PRIME](../advanced_config/parameter_reference.md#SENS_GPS_PRIME) to the CAN node ID of the _Moving Base_ (see [PX4 Configuration](#px4-configuration)).
 
 Setup via UART:
 
@@ -154,6 +156,7 @@ Setup via UART:
   - [GPS_YAW_OFFSET](../advanced_config/parameter_reference.md#GPS_YAW_OFFSET) to `0` if your _Rover_ is in front of your _Moving Base_, `90` if _Rover_ is right of _Moving Base_, `180` if _Rover_ is behind _Moving Base_, or `270` if _Rover_ is left of _Moving Base_.
 - On the _Moving Base_, set the following:
   - [GPS_UBX_MODE](../advanced_config/parameter_reference.md#GPS_UBX_MODE) to `2`.
+- On the _Flight Controller_, set [SENS_GPS_PRIME](../advanced_config/parameter_reference.md#SENS_GPS_PRIME) to the CAN node ID of the _Moving Base_ (see [PX4 Configuration](#px4-configuration)).
 
 For more information see [Rover and Moving Base](../dronecan/index.md#rover-and-moving-base) in the DroneCAN guide.